Panasonic Kx Tg4771 Operating Instructions Manual

Main menu:   “
Ringer volume ”Operation Settings Code
Adjusting the ringer volume. (Base unit)
Off–6 #16014Main menu:   “
I
nitial settings ”Sub-menu 1 Sub-menu 2 Settings Code
Contrast
(

Display contrast) –
Level 1–6  #145–
Caller ID edit
(
 Caller ID number auto edit) –

Off #214
29
Change language
(
 Display) (Base unit) –

Español #110
12Main menu:   “
C
ustomer support ”Operation Code
Displaying customer support Web address.
#680–n
 
Handset
Main menu:   “
C
aller list ”Operation Code
Viewing the...

Sub-menu 1 Sub-menu 2 Settings Code
Answer on
* 1
––#32731
Answer off *
 1
––#32831Main menu:   “
V
.M. access ” (V.M.: Voice mail)Operation Code
Listening to voice mail messages.
#33036Main menu:   “
I
ntercom ”Operation Code
Paging the desired unit.
#27438Main menu:   “
S
et date & time ”Sub-menu 1 Sub-menu 2 Settings Code
Date and time
*
 1
– –#10112
Alarm –1: O
nce
2:  Daily
0:   #720
25
Time adjustment *
 1, *3
–1: < Caller ID auto >
0:  Manual #226
–Main menu:   “
I
nitial setting ”Sub-menu 1...

Sub-menu 1 Sub-menu 2 Settings Code
Call block
* 1
– –#21726
Block w/o num *
 1, *2
(Block calls without phone
number) 1:
 On  0:   #24026
Voice mail Store VM access#*
 1
( VM : Voice mail) –
#33136
VM tone detect *
 1
1: < On> 0:  Off #33236
Message alert –1: 
< On> 0:  Off #34035
LCD contrast
(
 Display contrast) –
1–6: Level 1–6  #145–
Key tone *
 7
–1: < On> 0:  Off #165–
Caller ID edit
(
 Caller ID number auto edit) Handset
1: < On> 0:  Off #21429
Base unit *
 1
1: < On> 0:  Off #G 214
Auto talk *...

*3 This feature allows the unit to automatically adjust the date and time each time caller information
i ncluding date and time is received.
To turn this feature on, select  “Caller ID auto ”. To turn this feature off, select  “Manual ”. (Caller
ID subscribers only)
To use this feature, set the date and time first (page 12).
*4 If you subscribe to a distinctive ring service (such as IDENTA-RING), select a tone (tone 1 to 5). If you select a melody, you cannot distinguish lines by their ringers.
*5 If you...

Special programming
Alarm
A n alarm sounds at the set time for 3 minutes
once or daily. Alarm can be set for each handset.
Important:
R Set the date and time beforehand (page 12). Handset
1 MM

ENUN#720
2 Mb N: Select the desired alarm option.  a
M SELECT N
Off Turns alarm off. Go to step 7.
Once An alarm sounds once at the set
t

ime.
Daily An alarm sounds daily at the set
t

ime. Go to step 4. 3
E
nter the desired month and date.  a M OK N
4 Set the desired time.
5 MAM/PM N: Select  “AM ” or  “PM ”.  a...

Call block (Caller ID subscribers only)
T his feature allows the unit to reject calls when:
– the unit receives a call from a phone number stored in the call block list as unwanted (“Storing
unwanted callers”, page 26).
– the unit receives a call without phone number (“Blocking incoming calls without phone
number”, page 26).
When a call is received, the unit rings for a short
time while the caller is being identified. If the
phone number matches an entry in the call block
list, the unit sends out a busy...

Registering a h
andset to the base unit
The supplied handset and base unit are
pre-registered. If for some reason the handset is
not registered to the base unit, re-register the
handset.
1 Handset:
MMENU N#130
2 Base unit:
Press and hold  MLOCATOR N for about 5
seconds until the registration tone sounds.
R If all registered handsets start ringing, press
MLOCATOR N again to stop, then repeat this
step.
R The next step must be completed within 90
seconds.
3 Handset:
Press  MOK N, then wait until a long...

Using Caller ID service
I mportant:
R This unit is Caller ID compatible. To use Caller
ID features, you must subscribe to a Caller ID
service. Contact your service provider/telephone
company for details. Caller ID features
Base unit / Handset
W
 hen an outside call is being received, the caller’s
name and phone number are displayed.
Caller information for the last 50 callers is logged
in the caller list from the most recent call to the
oldest.
R If the unit cannot receive caller information, the...

Handset
1 M N
 a  M MENU N
2 Mb N:  “Group ” a  M SELECT N
3 Mb N: Select the desired group.  a M SELECT N
4 Mb N: Select the current setting of the ringer ID.
a  M SELECT N
5 Mb N: Select the desired ringer tone.  a M SAVE N
6 MOFF N Caller list
I
 mportant:
R Only 1 person can access the caller list at a
time.
R Make sure the unit’s date and time setting is
correct (page 12). Viewing t
he caller list and calling back
Base unit / Handset
1 P

roceed with the operation for your unit.
Base unit:  M CID N...

Note:
R
P
hone numbers from the 4 most recently edited
area codes are automatically edited. Erasing selected caller information
Base unit / Handset
1 P

roceed with the operation for your unit.
Base unit:  M CID N
Handset:  M F N CID
2 Mb N: Select the desired entry.
3 MERASE N a  M b N:  “Yes ” a  M SELECT N
4 Proceed with the operation for your unit.
Base unit:  M EXIT N
Handset:  MOFF N Erasing all caller information
Base unit / Handset
1 P

roceed with the operation for your unit.
Base unit:  M CID...