Panasonic Kx Tg2970 Operating Instructions Manual

11
Installation
Preparation
For assistance, please call: 1-800-ADT-ASAP
Charger unit
•Charger unit: USE ONLY WITH Panasonic AC ADAPTOR KX-TCA1 (Order No. 
KX-TCA1-G).
•The AC adaptor must remain connected at all times. (It is normal for the adaptor to 
feel warm during use.)
•The AC adaptor should be connected to a vertically oriented or floor-mounted AC 
outlet. Do not connect the AC adaptor to a ceiling-mounted AC outlet, as the 
weight of the adaptor may cause it to become disconnected.
Installing the...

Installation
12
Battery Charge 
Place the cordless handset on the 
charger and charge for 6 hours before 
initial use.
•The unit beeps once, the CHARGE indicator 
lights and “Charging” is displayed. 
•When the battery is fully charged, “Charge 
completed” is displayed if there are no new 
calls in the Caller List.
Battery strength
You can confirm the battery strength on the cordless handset display.
Battery strength is indicated by the icons shown in the chart below.
Recharge
Recharge the battery when:
—...

13
Installation
Preparation
For assistance, please call: 1-800-ADT-ASAP A nickel metal hydride battery that is recyclable powers the product 
you have purchased. Please call 1-800-8-BATTERY for information 
on how to recycle this battery
.
Battery information
After your Panasonic battery is fully charged, you can expect the following 
performance:
•A fully charged battery will give you up to 6 hours of continuous talk time, or keep 
your cordless handset in Standby mode to receive incoming calls for up...

14
Programmable Settings
Programming Guidelines
The base unit and the cordless handset have programmable functions. They are 
selected from the function menu on the display (p. 16, 17).
How to select a function item from the menu
Make sure the base unit and the cordless handset are not being used. 
The cordless handset must be operated near the base unit and while off 
the charger.
1Base unit: Press [FUNCTION/EDIT].
Cordless handset: 
Press [CONF/FUNCTION].
2Press [] at “Telephone”.
•The main menu is...

15
Programmable Settings
Preparation
For assistance, please call: 1-800-ADT-ASAP Useful information
•“---------------” indicates the beginning or end of the function menu.
•You can go back to the previous display by pressing
 [] except when entering 
characters or numbers. To return to the main menu from the sub-menu, press
 [].
•After programming is complete, the display will return to the main menu or the 
sub-
menu depending on which menu the selected item is located. (See the menu 
tables on pages 16...

Programmable Settings
16
Function Menu Table
After pressing [FUNCTION/EDIT] on the base unit or [CONF/FUNCTION] on the 
cordless handset, select “Telephone” to customize your unit using the following 
functions. See the corresponding pages for function details.
Base unit
*The items with “ ” in the menu table can be programmed with either the base 
unit or the cordless handset. You do not need to program these items on both 
the base unit and the cordless handset.
Main menuSub-menu ISub-menu  II...

17
Programmable Settings
Preparation
For assistance, please call: 1-800-ADT-ASAP
Cordless handset
*The items with “ ” in the menu table can be programmed with either the base 
unit or the cordless handset. You do not need to program these items on both 
the base unit and the cordless handset.
Main menuSub-menu ISub-menu  II
Telephone
Security
*
*
*
Ringer volume
Ringer tone
Incoming call
Copy 1 item
Copy all items
LCD contrast
Auto talk
Caller ID edit
Set tel lineSet dial mode
Set flash time
Set line...

Programmable Settings
18
Date and Time 
We recommend you set the date and time so that the unit will announce the day 
and time each message was recorded when you play back messages.
•When entering the time, you cannot enter numbers greater than 12. Do not use 
military time. (To set 13:00 hours, enter “0100”, and select “PM”
.)
1Press [FUNCTION/EDIT].
2Press [] at “Telephone”.
3Scroll to “Date and time” by pressing [] 
or [], then press
 []. 
4(1) Enter 2 digits each for the month, day and 
year. (Ex....

19
Programmable Settings
Preparation
For assistance, please call: 1-800-ADT-ASAP
Dialing Mode (use either   or  )
If you have touch tone service, set the dialing mode to “Tone”. For rotary or pulse 
service, set to “Pulse”. The factory preset is “Tone”.
Press [CONF/FUNCTION], and follow steps 2 to 6 above, using the 
cordless handset. Press the soft key ( ), then press [OFF].
1Press [FUNCTION/EDIT].
2Press [] at “Telephone”.
3Scroll to “Initial setting” by pressing 
[] or [], then press
 [].
4Scroll to...

Programmable Settings
20
Line Mode (use either   or  )
The line mode is preset to “B” and generally should not be adjusted. If “  ” is 
not displayed properly, the line mode selection is incorrect. Set line mode to “A”.
 
Press [CONF/FUNCTION], and follow steps 2 to 6 above, using the 
cordless handset. Press the soft key ( ), then press [OFF].
1Press [FUNCTION/EDIT].
2Press [] at “Telephone”.
3Scroll to “Initial setting” by pressing 
[] or [], then press
 [].
4Scroll to “Set tel line” by pressing [] or...