Panasonic Kx Tg2750 Operating Instructions Manual

							51For assistance, please call: 1-800-211-PANA(7262)
Useful Information
Belt ClipHandset
You can hang the cordless handset on your belt or pocket using the belt clip.
To attach the belt clip To remove the belt clip
Optional Headset
Plugging the optional headset into the cordless handset allows for hands-free 
phone conversation. Please use only a Panasonic KX-TCA60, KX-TCA86, 
KX-TCA88, KX-TCA91, KX-TCA92 or KX-TCA98 headset. To order, call the 
accessories telephone number on page 2.
Connecting an optional headset
Open the headset jack cover, and connect the optional headset to the headset jack 
as shown below.
•Headset sold separately. Model shown here is KX-TCA88.
To switch to the speakerphone while using the headset:
Press []. To return to the headset, press []. 
AB While pressing the top of the clip 
(A), pull the right edge in the 
direction of the arrow (B). 
Handset
Headset Jack 
						

							52
Wall Mounting
This unit can be mounted on a wall phone plate.
1Pull down the handset hook until it locks, so 
the tab holds the handset. 
2Press the tabs in the direction of the arrows ( ), then remove 
the wall mounting adaptor ( ).
3Connect the AC adaptor. Tuck the telephone line cord inside 
the wall mounting adaptor, then push it in the direction of the 
arrows ( ) and ( ). 
•The word “UP WALL” should face upward.
Wall Template for the Charger unit
1
2
2
11
12
To  P ower 
Outlet
11
22
2.45 cm(15⁄16) 
						

							53
Wall Mounting
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
4Connect the telephone line cord. 
Mount the base unit, then slide 
down. 
•Raise the antennas.
Charger unit
The charger can be wall mounted. Connect the AC adaptor. Install screws 
using the wall template (p. 52). Mount the charger ( ). Slide it down ( ), 
then slide down to the right ( ) until it is secured.
To temporarily set the handset down 
during a conversation, place it as shown 
here.
12
3
$
#
%
To  P ower 
OutletScrews2.45 cm
 (
15⁄16) 
						

							54
Canceling Registration/Re-registration
Canceling the Handset Registration
If you no longer need to use the cordless handset or if you want to use the cordless 
handset with a different base unit of the same model, it is necessary to cancel the 
registration from the current base unit.
Only one cordless handset can be canceled at a time near the base unit.
Make sure the cordless handset and the base unit are not being used.
•“[-]” is shown on the top right of the display. 
•After canceling registration, the cordless handset will not work. To use it again, 
registration will be required (p. 20, 55). 
1Press [CONF/FUNCTION].
2Scroll to “Initial setting” by pressing 
[] or [], then press
 [].
3Scroll to “Registration” by pressing [] 
or [], then press
 [].
4Scroll to “Deregistration”, by pressing 
[] or [], then press
 []. 
5Press [3][3][5] to delete the registration 
memory.
•If you make a mistake, press [HOLD/CLEAR], 
and enter “335”.
6Press the soft key ( ).
•The registration memory will be erased on both 
the cordless handset and the base unit.
•If 3 beeps sound, you entered a wrong code. 
Enter “335”, then press the soft key ( ). 
•To register the cordless handset to another base 
unit of the same model, start from step 5 on 
page 55 or see page 20.
Handset
▼Initial setting

Registration

Deregistration
Deregistration
Enter code:335
            :335
OK
OK
            
Handset [2]
  Deregistered
[-]
Ex. Extension number 2 
						

							55
Canceling Registration/Re-registration
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
Re-registering the Handset
If you want to re-register the cordless handset to the base unit or a different base 
unit of the same model, you need to register it to that base unit. The cordless 
handset will be given a new extension number of that base unit. Only one cordless 
handset can be registered at a time near the base unit. 
Make sure the base unit and the other cordless handsets are not being used. 
Registration must be completed within 1 minute.
•You can stop registration by pressing [OFF] on the cordless handset and pressing 
[MUTE] on the base unit. If you have canceled handset registration at a previous base unit (p. 54), start 
from step 5. 
1Cordless handset:
Press [CONF/FUNCTION].
2Cordless handset:
Scroll to “Initial setting” by pressing 
[] or [], then press
 [].
3Cordless handset:
Scroll to “Registration” by pressing [] 
or [], then press
 [].
4Cordless handset: 
Press [] at “HS registration”.
5Base unit: Press [MUTE].
•The MUTE indicator flashes.
6Cordless handset:
(1) Press the soft key ( ).
(2) Wait until a long beep sounds and the 
display shows the number. 
•Registration is complete.
If you have not canceled the cordless handset registration at the previous base 
unit (p. 54), the handset number still remains on that base unit memory. To erase 
the handset number from the previous base unit, see the base unit Operating 
Instructions. For KX-TG2750S base unit: (1) Press [FUNCTION/EDIT], (2) Press 
[MUTE], (3) Enter “335#”, and (4) Enter that handset number (1 to 8).
Base Unit & Handset
▼
Initial setting


Registration

HS registration
OKPress MUTE on
base unit, then
OK on handset to
register handset
            
Handset [2]
   Registered
[2]
Ex. Extension number 2 
						

							56
If the Following Appear on Your Display...
If the unit detects a problem, one of the following messages will be displayed on the 
base unit or the cordless handset. Error beeps or a busy tone will sound.
Display messageCause & Remedy
Recharge battery(cordless handset only)•The battery needs to be charged. Recharge the 
battery (p. 12).
Charge for 15HRS(cordless handset only)•The battery has been discharged. The cordless 
handset will not work. Charge the battery fully (p. 12).
No link to base.
Walk closer to 
base and try 
again.
(cordless handset only)•The cordless handset has lost communication with 
the base unit. Walk closer to the base unit, and try 
again.
•Plug in the base unit’s AC adaptor.
•Raise the base unit antennas.
Busy•The called unit is in use.
•The Privacy mode is on for the call you tried to join 
(p. 41).
•The unit you tried to send directory items to is in use.
•The cordless handset you are calling is too far from 
the base unit.
Invalid•The called cordless handset has not been registered 
to the base unit. 
•You selected your own extension number.
•You pressed [9] instead of entering an extension 
number. Enter the extension number (0 to 8) to call.
     Error!!
•When you tried to register or deregister the cordless 
handset, the cordless handset and the base unit 
could not link for some reason, such as interference 
from other electrical appliances. Move the cordless 
handset and the base unit away from electrical 
appliances and try again.
•If more than one cordless handset is in use, you may 
not be able to register/deregister. Try again later.
•Another unit tried to send directory items to you but 
the transfer has been stopped (p. 34, 35).
Directory 
      Full•When you tried to store an item in the directory, the 
directory memory is full. Press [EXIT] on the base 
unit or [OFF] on the cordless handset to exit the 
programming mode. To erase other items from the 
directory, see page 33. 
						

							57
If the Following Appear on Your Display...
Useful Information
For assistance, please call: 1-800-211-PANA(7262) System is busy.
Please try again
later.•If radio communication between the cordless 
handset and the base unit is partially impaired, this 
display will be shown.
---Incomplete---
Tom Jones
098-765-4321
 Directory full
(The name/number is 
an example.)•When the displayed item is being sent to the 
destination unit, the directory memory is full and the 
transfer is stopped. If you tried to send all of the 
items, the item displayed with “Incomplete” and 
items after it have not been transferred to the 
destination unit. You can press [OFF] on the cordless 
handset or [EXIT] on the base unit to exit 
(p. 34, 35). To erase other stored items from the 
destination unit directory, see page 33. You can send 
all of the items again or send the items which have 
not been transferred one by one (p. 34, 35).
•If the transfer is stopped and “Directory full” is 
not displayed, it may indicate:
– the destination cordless handset is out of area, or
– the destination unit user may have pressed [] or 
[] on the cordless handset, or lifted the base unit 
handset or press [DIGITAL SP-PHONE]. 
Directory
No items stored•Although you tried to send your directory items to 
another extension, your directory is empty.
Denied•When you call another unit to monitor, the Room 
Monitor mode of the destination unit is set to OFF 
(p. 41).
Not found
2Way radio mode
(cordless handset only)•When you tried to call another cordless handset in 
2-Way Radio mode;
– the cordless handset is too far from your cordless 
handset. Walk closer to the cordless handset.
– 2-Way Radio mode on the cordless handset is off 
(p. 43).
– The cordless handset you called is talking with 
another cordless handset in 2-Way Radio mode.
Invalid.
Please register 
to the base unit
(cordless handset only)•The cordless handset you tried to make a call has not 
been registered to the base unit. Register the 
cordless handset (p. 20, 55).
Store VM access#•You have not stored the voice mail access number.
Store the number (p. 45).
Display messageCause & Remedy 
						

							If the Following Appear on Your Display...
58
     Error!!
8 handsets have
already been
registered.
(cordless handset only)•8 cordless handsets have already been registered to 
the base unit. To cancel another handset registration, 
see page 54. 
•This base unit has the memory of the cordless 
handset currently registered to another base unit. 
Erase the handset memory from the base unit. 
For KX-TG2750S base unit: 
(1) Press [FUNCTION/EDIT], (2) Press [MUTE], 
(3) Enter “335#” and (4) Enter that handset number 
(1 to 8).
Display messageCause & Remedy 
						

							59For assistance, please call: 1-800-211-PANA(7262)
Useful Information
Troubleshooting
If the display shows error messages, see “If the Following Appear on Your 
Display...” (p. 56–58) for the Cause & Remedy.
Problem Cause & Remedy
The unit does not work. • Check the settings (p. 10–12).
•Check whether the dialing mode setting is 
correct (p. 17).
•Charge the battery fully (p. 11).
•Clean the charge contacts and charge again 
(p. 12).
•Install the battery properly (p. 11).
•Unplug the base unit’s AC adaptor to reset it. 
Plug in, and try again.
•The cordless handset has not been 
registered to the base unit. Register the 
cordless handset (p. 20, 55).
•Re-install the battery (p. 11) and charge it 
fully.
Static, sound cuts in/out, 
fades. Interference from other 
electrical units.•Move the cordless handset and the base unit 
away from other electrical appliances (p. 3).
•Walk closer to the base unit.
•Raise the base unit antennas.
•Press
 [] on the cordless handset to turn on 
the Reception Booster feature (p. 24).
The base unit and/or cordless 
handset does not ring.•The ringer volume is OFF. Set to HIGH, 
MEDIUM or LOW (p. 18).
•If more than one other unit is in use, the 
cordless handset/base unit may not ring. 
Users will hear incoming call tones (p. 49).
The display of the base unit or 
cordless handset is blank.•If only the cordless handset display is blank, 
charge the battery fully (p. 11).
•If you are having a conversation using the 
base unit handset during a power failure and 
power returns to the base unit, the display will 
be blank until you hang up the call. After 
hanging up, the display will function.
While programming or 
searching, the unit starts to 
ring and stops the program/
search.•A call is coming in. To answer the call, lift the 
base unit handset, or press [DIGITAL 
SP-PHONE], [] or []. Start again from 
the beginning after hanging up.
▼ 
						

							Troubleshooting
60
You cannot program function 
items.•Programming is not possible while the unit is 
being used.
•Do not pause for over 60 seconds while 
programming.
•Walk closer to the base unit if you are using 
the cordless handset.
•If more than three other units are in use, you 
may not be able to program with the base unit 
or cordless handset. Try again later.
•If 2-Way Radio mode is on on your cordless 
handset, turn it off (p. 43).
You cannot make an intercom/
external call.•If more than one other unit is in use, you may 
not be able to make a call. Try again later.
•The cordless handset you called is too far 
from the base unit.
•If 2-Way Radio mode is on on your cordless 
handset, turn it off (p. 43).
•If you are having a conversation using the 
base unit handset during a power failure and 
power returns to the base unit, you cannot 
use the speakerphone nor the cordless 
handset until you hang up the call. After 
hanging up, you can resume all functions.
The unit does not display the 
caller’s name and/or phone 
number.•You need to subscribe to a Caller ID service.
•Other telephone equipment may be 
interfering with your phone. Disconnect it and 
try again.
•Other electrical appliances connected to the 
same outlet may be interfering with the Caller 
ID information.
•Telephone line noise may be affecting the 
Caller ID information.
•The caller requested not to send his/her 
information. See page 25.
•If a call is being transferred to you, the Caller 
ID information will not be displayed.
•If a (separate) Caller ID box is connected 
between the unit and the telephone wall jack, 
disconnect the Caller ID box or plug the unit 
directly into the wall jack.
The display exits the Caller 
List or directory.•Do not pause for over 60 seconds while 
searching.
Problem Cause & Remedy