Panasonic Kx Tg2386 Operating Instructions Manual

Useful Information
For assistance, please call: 1-800-211-PANA(7262)71
Wall Mounting
This unit can be mounted on a wall phone plate.
1Push the hook and turn it 
upward. Turn the hook until a 
click is heard.
2Press the tabs in the direction 
of the arrows (1), then remove 
the wall mounting adaptor (2). 
 3Connect the AC adaptor. Tuck 
the telephone line cord inside 
the wall mounting adaptor, then 
push the adaptor in the direction 
of the arrows (1 and 2).
• The word “UP WALL” should face 
upward.
•...

72
Belt Clip
You can hang the handset on your belt or pocket using the included belt clip.
To attach the belt clip To remove the belt clip 
Shoulder Rest Attachment
Use the shoulder rest attachment if you need to keep your hands free during a 
phone conversation.
To attach the shoulder rest 
attachment
Attach the included belt clip to the 
handset (see above), then attach the 
shoulder rest attachment to the belt clip 
as shown below. You will hear a click 
when the shoulder rest attachment is in...

Useful Information
For assistance, please call: 1-800-211-PANA(7262)73
Optional Headset
Connecting an optional headset to the handset allows hands-free phone 
conversation. Please use only a Panasonic KX-TCA60, KX-TCA86, KX-TCA88, 
KX-TCA88HA, KX-TCA91, KX-TCA92, or KX-TCA98 headset. To order, call the 
accessories telephone number on page 2.
Connecting an optional headset
Open the headset jack cover, and insert the headset plug into the headset jack as 
shown below. 
• Headset sold separately. Model...

74
Direct Commands
After pressing [MENU], you can also program menu items directly by pressing [0] 
to [9], [*] and [#] instead of using the soft keys.
Menu item Command Selection items Page
Ringer volume[1] [1]  [0] : Off  [1] : Low  [2] : Medium   
[3] : Highp. 17
Ringer tone 
(for handset)[1] [2] [1]–[3] : Tone pattern 1–3 
[4]–[7] : Melody pattern 1–4p. 18
Incoming call tone 
(for handset)[1] [3]  [1] : On  [2] : 2  [0] : Off p. 59
Message play[2]p. 64
Date and time [4]Go to Step 3 on page 14. —...

For assistance, please call: 1-800-211-PANA(7262)75
Direct Commands
Useful Information
During programming:
When “Save” is displayed, press the right soft key to save the new settings.
To exit programming, press [OFF].
• If you press the direct command incorrectly, press [OFF], then re-enter 
programming mode by pressing [MENU].
• For function details, see the corresponding pages.
Number of rings[0] [6] [1] [2]–[7] : 2–7 rings  
[0] :       Toll saverp. 26
Recording time[0] [6] [2] [1] : 1 minute  [2] : 2...

76
If the Following Appear on Your Display...
The following will be displayed when the unit needs your attention.
Display message Cause & Remedy
Recharge battery• The battery needs to be charged. Recharge the 
battery (p. 10).
 Charge for 6h• The battery has been discharged. The handset will 
not work. Fully charge the battery (p. 10).
No link to base. 
Move closer to 
base, try again.• The handset has lost communication with the base 
unit. Walk closer to the base unit and try again or re-
register the...

Useful Information
For assistance, please call: 1-800-211-PANA(7262)77
Troubleshooting
If the handset display shows error messages, see “If the Following Appear on 
Your Display...” (p. 76) for the Cause & Remedy.
Telephone System
Problem Cause & Remedy
“No link to base. Move 
closer to base, try 
again.” is displayed and an 
alarm tone sounds.• You are too far from the base unit. Walk 
closer to the base unit.
• Confirm the base unit’s AC adaptor is 
plugged in.
• Raise the base unit antenna.
• If the...

Troubleshooting
78
You cannot make an intercom/
outside call.• Your handset is in remote operation mode 
(p. 64). Exit by pressing [OFF].
• The handset you called is too far from the 
base unit.
• If the handset or base unit is in use, you may 
not be able to make a call. Try again later.
• If you are entering a phone number, or the 
handset enters the Caller List, phone book, 
redial list or one-touch dialer while the Talking 
Keypad or Announcement is turned on, you 
will not be able to make an outside...

For assistance, please call: 1-800-211-PANA(7262)79
Troubleshooting
Useful Information
The handset and/or base unit  
does not announce the 
displayed caller’s name.• The handset and/or base unit ringer volumes 
are turned off. Set to high, medium, or low 
(p. 17, 18).
• The Talking Caller ID feature is turned off. 
Turn it on (p. 36, 37).
The handset and/or base unit  
does not announce the 
displayed caller’s name 
properly.• Name pronunciation may vary. Name 
pronunciation quality is based on names...

Troubleshooting
80
The handset does not 
announce the entered number 
when pre-dialing (p. 30).• Handset Talking Keypad is turned off. Turn it 
on (p. 20).
The base unit does not 
announce the dialed number.• Base Unit Talking Keypad is turned off. Turn it 
on (p. 21).
When Talking Keypad and/or 
Name Announcement is 
turned on, the handset and/or 
base unit does not make 
announcements.• The Answering System is in use, such 
answering a call or playing back messages. 
Try again later.
• The handset has...