Panasonic Kx Tg2227 Operating Instructions Manual

Recharge
When the RECHARGE indicator flashes
or the unit beeps intermittently while it is
use, place the handset on the base unit to
recharge the battery for 15 hours.
•If you DO NOT recharge the handset battery
for more than 15 minutes, the RECHARGE
indicator will continue to flash.
11
Preparation
For assistance, please call: 1-800-211-PANA(7262)
Up to 11 days
OperationOperating time
While in use (TALK)Up to 5 hours
While not in use (Standby)
•The battery operating time may be shortened depending on usage...

12
Dialing Mode
You can program the dialing mode using the handset near the base unit.
If you have touch tone service, set to TONE. If rotary or pulse service is
used, set to PULSE. Your phone comes from the factory set to TONE.
Make sure the unit is not being used and the handset is lifted off the
base unit.
1
Press (PROGRAM).
•The TALK/MUTE indicator flashes.
2
Press á.
3
To select PULSE, press (#)twice.
OR
To select TONE, press 
(*)twice.
4
Press (PROGRAM).
•A beep sounds.
•You can exit the programming...

13
Preparation
For assistance, please call: 1-800-211-PANA(7262)
Line Mode
If the line is connected to a low voltage system such as a PBX, set to “B”. 
Your phone comes from the factory set to “A”.
Make sure the unit is not being used and the handset is lifted off the
base unit.
1
Press (PROGRAM).
•The TALK/MUTE indicator flashes.
2
Press 
(FLASH/CALL!WAIT/PLAYBACK).
•“P” is displayed on the base unit.
3
Press (3).
•The current setting is displayed on the 
base unit.
4
To select “A”, press (1).
OR
To...

14
Ringer Pattern
You can select the handset ringer pattern out of 6 patterns. When an
incoming call is being received, the unit rings in the selected pattern.  
Make sure the unit is not being used and the handset is lifted off the
base unit.
1
Press Üor á.
•The unit rings at the current setting.
•If you set the ringer volume to OFF, the unit will not ring.
2
Within 5 seconds, select the desired ringer pattern by pressing Üor
á.
•Each time you press the button, the ringer pattern will change and ring....

15
Preparation
For assistance, please call: 1-800-211-PANA(7262)
To record a greeting message
1
Press and hold (GREETING)until
“Record greeting after the beep” is
heard.
•A long beep sounds.
2
Talk clearly, about 8 inches
(20 cm) away from the MIC
(microphone).
•The base unit display shows the
elapsed recording time.
•If you record for over 2 minutes,
the unit will automatically stop
recording.
3
When finished, press (GREETING).
•The unit will automatically play back
the recorded greeting.
•You can also...

16To check the recorded greeting message
Press (GREETING).
To erase the recorded greeting message
Press (GREETING)\Press (ERASE)while the message is being played.
•The unit will answer a call with a pre-recorded greeting.
Pre-recorded greeting message
If you do not record a greeting message (p. 15), one of two messages will
be played when a call is received, depending on the caller’s recording
time (p. 19).
To check the pre-recorded greeting, press 
(GREETING).
•A pre-recorded greeting will be played as...

17
Preparation
For assistance, please call: 1-800-211-PANA(7262)
Programming Summary for Answering System
You can program the following functions using the handset near the
base unit.See the corresponding pages for function details.
Make sure the unit is not being used and the handset is lifted off the
base unit.
•You can exit the programming mode any time by pressing (OFF).
•If you do not press any buttons for 60 seconds, the unit will exit the programming
mode.
Press (PROGRAM).
Press...

Make sure the unit is not being used and the handset is lifted off the
base unit.
1
Press (PROGRAM).
•The TALK/MUTE indicator flashes.
2
Press (FLASH/CALL!WAIT/PLAYBACK).
•“P” is displayed on the base unit.
3
Press (0).
•“Set time” is announced from the
base unit. If previously adjusted, the
day/time will be heard.
4
Enter the current time (hour and
minute) using a 4-digit number.
(Ex. To set 9:30, enter “0930”.)
•The 2 digits of the entered number is
displayed.
5
Press (*)to select “AM” or “PM”.
Press...

Make sure the unit is not being used and the handset is lifted off the
base unit.
1
Press (PROGRAM).
•The TALK/MUTE indicator flashes.
2
Press (FLASH/CALL!WAIT/PLAYBACK).
•“P” is displayed on the base unit.
3
Press (5).
•The current setting is displayed on
the base unit.
1: 1 minute
2: 2 minutes 
3: 3 minutes
Blank: Greeting only
4
Press (1), (2), (3)or (0)to select the
recording time.
•The setting is displayed on the base
unit.
1: 1 minute
2: 2 minutes 
3: 3 minutes
0: Greeting only
5
Press (PROGRAM).
•A...

20
1
Press (PROGRAM).
•The TALK/MUTE indicator flashes.
2
Press (FLASH/CALL!WAIT/PLAYBACK).
•“P” is displayed on the base unit.
3
Press (2).
•The current setting is displayed on 
the base unit.
4
Press (0), or (2)to (7)to set the 
number of rings.
0: Selects “AUTO”. 
“A” is displayed.
2–7: The unit will answer after the
selected number of rings.
5
Press (PROGRAM).
•A beep sounds from the base unit.
Number of Rings
You can select the number of times the unit rings before the answering
system answers a...