Panasonic Kx Td500 User Manual

Appendix
User Manual541
Extrnl Page 1 RECH. EXT. 1Access to Paging — External (- to a specific 
external pager).
FWD(ALL) Ext1234 RNV(TOUS)PST1234Complete to set Call Forwarding — All 
Calls.
Confirm key programming on the FWD/DND 
button.
FWD(B/NA)Ext1000 RNV(O/SR)PST1000Complete to set Call Forwarding — Busy/
No Answer.
Confirm key programming on the FWD/DND 
button.
FWD(BSY) Ext2345 RNV(OCC) PST2345Complete to set Call Forwarding — Busy.
Confirm key programming on the FWD/DND 
button.
FWD(CO) 91201431...

Appendix
542User Manual
In a Meeting In a MeetingAbsent Message 6.
Locked NO. : 123 CODE VERR. : 123Complete to set Electronic Station Lockout.
Log Locked :123 REG FERME : 123Complete to set Call Log Lock, Incoming.
Message Cancel MESSAGE ANNULECancel Absent Message.
MODEM command 1 COMMANDE MODEM 1Complete to send an AT Command to the 
external modem.
— External Modem Control
MW at Ext 1234 MESS. PST 1234Complete to set Message Waiting.
MW Not Accepted MESS ATT. REFUSENot complete to set Message...

Appendix
User Manual543
Ringer : *** SONN. : ***Volume Control — ringer on idle status.
SP:************ HP:************Volume Control — speaker on hands-free 
mode.
Transfer to CO TRANSFERT A LRThe destination extension is set Call 
Forwarding — to Outside Line.
Try Again RESSAYERWhen the destination extension is in one of 
the following states.
 — Off-hook, incoming call
 — Call Hold
 — All buttons on PT are in use
Unlocked DEVERROUILLECancel Call Log Lock, Incoming.
Cancel Electronic Station Lockout....

Appendix
544User Manual
Examples – in Station Programming mode
English Display French Display Description
Account COMPTEAccount button is assigned.
C.W. Tone1 TON.APPEL1Select Call Waiting tone.
Clear Ready? ANNULER DONNEES?Available to clear Station Programming data.
CO-10101 LR-10101Single-CO (S-CO) button is assigned.
Conference CONFERENCEConference (CONF) button is assigned.
1400:CO Lock 1400:LR VERR.Complete to lock the outside calls of other 
extension.
— Remote Station Lock Control.
1400:ICM Lock...

Appendix
User Manual545
Conditions
If the displayed characters exceed 16 digits, & is shown at the right-hand edge.
The duration time display is only shown when you make or receive an outside call. Count 
start time for outgoing calls can be programmed as desired.
When you confirm key programming, be sure to press a button while on-hook. If the Full 
One-Touch Dialing feature is set, dialing mode will start when pressing PF (Programmable 
Feature), DSS (Direct Station Selection), SAVE or REDIAL...

Appendix
546User Manual
6.1.2 Feature Numbers List
Numbers listed below are the initial factory settings (default value). There are flexible feature 
numbers and fixed feature numbers. The flexible feature numbers can be changed by System 
Programming .
Flexible Feature Numbers
Feature Default Additional Digits
1st hundred block extension 10 00-99
2nd hundred block extension 11 00-99
3rd hundred block extension 12 00-99
4th hundred block extension 13 00-99
5th hundred block extension 14 00-99
6th hundred...

Appendix
User Manual547
Call Pickup, Group 40
Call Pickup Deny set/cancel 720 1 / 0
Call Waiting set/cancel 731 1, 2, 3 / 0
Calling Line Identification Presentation 
(CLIP)711 1 / 2
Calling Line Identification Restriction (CLIR)/
Calling Name Identification Restriction 
(CNIR)59 0 / 1 / 2
Data Line Security set/cancel 730 1 / 0
Dial Information (CTI)—code + # / 99
Do Not Disturb (DND) set/cancel 710 1 / 0
Doorphone Call calling 31 1-8
Doorphone Call door open 55 1-8
Electronic Station Lockout set 762...

Appendix
548User Manual
Paging — All 32 / 33
Paging — External 32 0 / 1-2
Paging — External Answer/TAFAS Answer  42 1 / 2
Paging — Group  33 01-16
Paging — Group Answer 43
Paging Deny set/cancel 721 1 / 0
Paralleled Telephone Connection set/cancel 39 1 / 0
Pickup Dialing (Hot Line) assign/set/cancel 74 2+phone no. +# / 1 / 0
Quick Dial 1-8—
Redial, Last Number #
Remote DND (Do Not Disturb) set/cancel 722 destination extension no.
Remote FWD (Call Forwarding) Cancel-Once 723 destination extension no....

Appendix
User Manual549
Conditions
Extension numbers can be three or four digits in length. Any number can be set as the 
leading first or second digit.
Flexible feature numbers can only be dialed while a dial tone is heard.
If   or # is included in a feature number, it will not be possible for users with dial pulse 
(DP) telephones to access the feature.
Feature Number Conflicts 
Examples: 1 and 11, 0 and 00, 2 and 21, 10 and 101, 32 and 321, etc.
Additional Digits
Some flexible feature numbers...

Appendix
550User Manual
example, to set Call Waiting, the feature number for Call Waiting must be followed by 1 
and to cancel it, the same feature number should be followed by 0.
Fixed Feature Numbers Type-1 or Type-2 can be selected by System Programming. 
(Default = Type-1)
Programming Guide References
1.4 Extension Port Assignment
– Attribute
– DN
2.3 Numbering Plan
2.8 System Option
– Fixed Feature Number
Features Guide References
1.3 System Features
Flexible Numbering
User Manual References
None