Panasonic Kx Taw848 PC Cprogramming Manual

2.14 [8] ARS
PC Programming Manual 401
Programming Manual References
None
Feature Manual References
1.1.3 ARS (Automatic Route Selection)
2.14.2 [8-2] Leading Number
Specifies the area codes and/or telephone numbers as leading numbers that will be routed by the 
ARS feature. A maximum of 1000 different leading numbers can be programmed, and each leading 
number can select a Routing Plan Table number, which determines the ARS procedure.
 
The additional (remaining) number of digits can also be specified...

2.14 [8] ARS
402 PC Programming Manual
Maintenance Console Location
2.14.2 [8-2] Leading Number
Programming Manual References
None
Feature Manual References
1.1.3 ARS (Automatic Route Selection)
Routing Plan Number
Specifies the Routing Plan Table number used for each leading number.
Default
1
Value Range
1–16
Maintenance Console Location
2.14.2 [8-2] Leading Number
Programming Manual References
None
Feature Manual References
1.1.3 ARS (Automatic Route Selection)
2.14.3 [8-3] Routing Plan Time
The start...

2.14 [8] ARS
PC Programming Manual 403
Default
Time-A–Time-C: Enable
Time-D: Disable
Value Range
Disable, Enable
Maintenance Console Location
2.14.4 [8-3] Routing Plan Time—Time Setting
Programming Manual References
None
Feature Manual References
1.1.3 ARS (Automatic Route Selection)
Time-A–D—Hour, Minute
Specifies the start time for each time block.
Default
Time-A: 8:00, Time-B: 17:00, Time-C: 21:00, Time-D: Not applicable.
Value Range
00:00–23:59
Maintenance Console Location
2.14.4 [8-3] Routing Plan...

2.14 [8] ARS
404 PC Programming Manual
Default
Priority 1: 1 
Priority 2–6: None
Value Range
None, 1–10
Maintenance Console Location
2.14.5 [8-4] Routing Plan Priority
Programming Manual References
None
Feature Manual References
1.1.3 ARS (Automatic Route Selection)
2.14.6 [8-5] Carrier
Carrier
It is possible to specify how user-dialed numbers are modified for connecting to the appropriate 
carrier. A maximum of 10 different carriers can be programmed to be used with the ARS feature.
Carrier Name...

2.14 [8] ARS
PC Programming Manual 405
Default
0
Value Range
0–15
Maintenance Console Location
2.14.6 [8-5] Carrier
Programming Manual References
None
Feature Manual References
1.1.3 ARS (Automatic Route Selection)
Modify Command
Specifies the commands to modify the user-dialed number to access the carrier. For details of each 
command, see the Feature Manual.
Default
CH
Value Range
Max. 16 characters (consisting of 0–9, *, #, C, P, A, G, I and H)
Maintenance Console Location
2.14.6 [8-5] Carrier...

2.14 [8] ARS
406 PC Programming Manual
Programming Manual References
None
Feature Manual References
1.1.3 ARS (Automatic Route Selection)
TRG 01–TRG 64
Selects the trunk groups that connect to the carrier.
TRG 01–TRG 64
Enables each trunk group for each carrier. If a cell is highlighted in blue, that trunk group is enabled 
for use with that carrier.
Default
Trunk groups 01–04: ON 
All other trunk groups: OFF
Value Range
OFF (white), ON (blue)
Maintenance Console Location
2.14.6 [8-5] Carrier
Programming...

2.14 [8] ARS
PC Programming Manual 407
Programming Manual References
None
Feature Manual References
1.1.3 ARS (Automatic Route Selection)
1.17.2 Tenant Service
2.14.7 [8-6] Leading Number Exception
Specifies telephone numbers that will not be connected using the ARS feature. When the user-dialed 
number includes a leading number exception, the PBX sends the number to a CO line by the Idle Line 
Access method if 
ARS Mode in 2.14.1 [8-1] System Settings is on. 
A maximum of 200 different leading number...

2.14 [8] ARS
408 PC Programming Manual
Value Range
Max. 10 digits (consisting of 0–9, *, and #)
Maintenance Console Location
2.14.8 [8-7] Authorization Code for TRG
Programming Manual References
2.14.6 [8-5] Carrier—Carrier—Modify Command
Feature Manual References
1.1.3 ARS (Automatic Route Selection) 

2.15 [9] CO & Incoming Call
PC Programming Manual 409
2.15 [9] CO & Incoming Call
2.15.1 [9-1] CO Line Settings
CO lines can be assigned a name, and grouped into a maximum of 64 trunk groups.
Physical—Slot
Indicates the slot position of each CO line card (reference only).
Default
Current slot number
Value Range
Slot number
Maintenance Console Location
2.15.1 [9-1] CO Line Settings
Programming Manual References
None
Feature Manual References
None
Physical—Port
Indicates the por t number (reference only)....

2.15 [9] CO & Incoming Call
410 PC Programming Manual
CO Name
Specifies the CO line name which is shown on the extensions display when receiving a call from the 
CO line.
Default
Not stored.
Value Range
Max. 20 characters
Maintenance Console Location
2.15.1 [9-1] CO Line Settings
Programming Manual References
None
Feature Manual References
1.4.7 Display Information
Trunk Group Number
Specifies the trunk group number to which the CO line belongs.
Default
1
Value Range
1–64
Maintenance Console Location...