Panasonic Kx T2470 Operating Instructions Manual

Initial Programming
Selecting the CPC (Galling Party Control)
The initial setting of the CPC mode is A.
oA mode: Use this mode if your telephone line does not have call waiting service.
oB mode: Use this mode if your telephone line has call waiting service.
lf some Incoming Messages are cut off in mode A, set the mode to B.
!ryiu{l
1
Be sure that the handset is on the cradle, the SP-PHONE indicator is off and the
AC adaptor is connected.
Press the PROGRAM button.
The MUTE/STORE indicator lights.
I...

Initial Programmihg rcont.)
Be sure that the handset is on the cradle. the SP-PHONE indicator is off and the
AC adaptor is connected.
Press the PROGRAM button.
The MUTE/STORE indicator lights.
ilri.
ir,l
;:t
r,O.tl.r.!)::iilii!,
o5
t.
1
I ttl+ [* Zl
W^01... [r-r]r.7l
Auto mode 7 rings
Press  # , lhen press 7 lol
number of rings setting.
The MUTE/STORE indicator goes out.
Select the number of rings by
pressing 0, 1, 2 ...or 7 .
O...auto mode (The display shows A.)
See AUTO setting on page 15.1...one ring...

Initial Programmihg rcont.)
Selecting the callers recording time
The callers recording time can be programmed to VOX, 1 Minute orAnnounce only.
The initial setting of the recording time is VOX (unlimited).
.VOX (Unlimited) mode: The recording time is limited by the length of the
taoe.
o1 Minute (Limited) mode: lt allows the caller to record for 1 minute.oAnnounce only mode: The unit plays back the OGM only and will not
record any Incoming Messages.
-t7 -)_--18-
SC=pnocnnv
Be sure that the handset is on...

Initial Programming (cont.)
Setting the remote code
Before operation, choose a 1-3-digit remote code number (1 through gg9) andstore it in memory.
The initial setting of the remote code is 1 1 1.
ll, 
ilji lil.vut lrt{rlOgE&A$-r*n,XFI
$o&JsF]$&E;r,rillll,:rll,i,li irl:rl.il:i.l.i
the handset is on the cradle, the SP-PHONE indicator is off and the
is connected.
Be sure that
AC adaptor
1re
tN
2:
lL
L
3V,
F
4rc
1
Press the PROGRAM button.
The MUTE/STORE indicator lights.
l #-l +fTl
Enter your code number....

Recording an Outgoing Message (OGM)
The OGM tells the caller that you are out, and asks lo leavo a mesBage.
You can record two OGMs.
I OGM 1s recording time is limited to 30 seconds. So you mRy loave a short
message.
f OGM 2 is an extended OGM and ils recordinq lime may llo rrp lo llrr. end of the
tape. You may leave a long message, such as advorltsomont lor your business.
OGM PLAY
button
lN USE indicator
OGM indicators
OGM 1 is selected. OGM 2 is selected
6tiFn 1 finFclff,i
nIJ
6rim 2 EFFSrff,l
nL
OGM...

Recording an Outgoing Message (cont.)
.r-
II
I
Checking your recorded message (OGM)
Press the OGM SELECT button
(OGM 1 or OGM 2).
The unit announces One or Two.
The selected OGMs indication on the
display flashes at first, then it will switch to
a steady light after the OGM tape has been
reser.
Press the OGM PLAY button to
listen to your recorded OGM.
Press the OGM PLAY button again if you
want to stop the operation at any time.
The tape rewinds, and the unit will be ready
to answer incoming calls after...

Manual Dialing and Receiving
Making calls using the handset
1 Lift the handset.
2 Dialthe telephone number.
Making calls using the SP-PHONE button
(on-hook dialing)
Press the SP-PHONE button,
and dialthe telephone number
The SP-PHONE indicator lights.
When the other party answers,
speak to the other party through
the microphone.
You can also switch to the handset at any
time by just lifting it.
Press the SP-PHONE button
again when you finish.
The SP-PHONE indicator goes out.
Helpfulhints
oWhen the other...

Automatic Dialing (cont.)
Be sure that the handset is on the cradle, the SP-PHONE indicator is off and the
AC adaptor is connected.
When you store a telephone number into memory, pressing the #, *, PAUSE or
FLASH button count as 1 digit.
Storing telephone numbers for speed dialing
There are 20 memory stations, each memory station can be accessed by dialing 2
Press the PROGRAM button.
The MUTE/STORE indicator lights.
Press the station number
(01-20).
The MUTE/STORE indicator goes oul
Dial the telephone...

Automatic Dial ihg rcont.)
Storing telephone numbers with secret feature
This function is useful for keeping a telephone number secret.
Press the SECRET STORE button instead of pressing AUTO/STORE button during
programmrng.
The secret telephone number will not be seen on the display and will not be
announced by voice memo check. (See page 32.)
Example: To store the secret telephone number into the memory station 02.
Press the PROGRAM button.
The MUTE/STORE indicator liohts.1
Press the station number 02...

i
1
Automatic Dialing (cont.)
Erasing a stored number
Erasing a number stored for one-touch dialing
Press the PROGRAM button.
The MUTE/STORE indicator lights.
Press the direct call button where
the number that you want to
erase is stored.
The MUTE/STORE indicator goes out.
Press the AUTO/STORE button.
The MUTE/STORE indicator lights.
Press the PROGRAM button.
The MUTE/STORE indicator qoes out.
Erasing a number stored for speed dialing
When you want to erase the telephone number for speed dialing, change...