Panasonic Kx P8410 Operating Instructions Manual

141
Turn off the printer and
the computer, then turn
them on again. Print the
document again. SCSI Error!! Time Out
occurred.
Unable to Allocate Memory The computer’s
internal memory for
printing is insufficient. The printer is not
responding.
Error messagePossible causeRecovery
Care and Maintenance
BClose all applications
except for the one
which controls the
printer, then print
again.
BTurn off the
computer, then turn it
on again.
Printing aborted for
occurred SCSI error.An illegal error has...

142
Care and Maintenance
Error messagePossible causeRecovery
*.DLL not found *.DLL function ErrorThe necessary file for
printing is not found.Reinstall the KX-P8410
software.
File ID not match!!
nSome application settings may take priority over the printer driver settings. Table file open error!!
Table file read error!!Resource DLL file is not
found. Check sum error!! 

143
Correctly install the
SCSI board and its
driver. (Refer to the
manual of the SCSI
board.)
wnaspi32.dllwill be
installed or replaced
with a new version.
For any other trouble
related to SCSI, refer to
the SCSIsection of
Care and Maintenance
( +P. 134).
The ASPI manager
installed on this PC does
not support Windows.
Install ASPI for Windows.
[e.g. install wnaspi32.dll to
your windows (system
directory)]. The ASPI for Windows
installed on this PC does
not support expected
mode. Install newer version
of...

144
Follow the procedure
below to make the setting
active.
1. Click Start, select
Settings, then click
Printers.
2. Click the Panasonic 
KX-P8410 printericon.
3. Click the File menu,
then click Properties.
4. Click Details tab and
Spool settings....
5. Click Enable bi-
directional support for
this printer, then click
OK.
Error messagePossible causeRecovery
Care and Maintenance
There was an error
writing to LPT1: for the
printer (Panasonic 
KX-P8410):
There was a problem
sending your document
to the...

145
Care and Maintenance
Resource DLL file is not
found.Reinstall the KX-P8410
software. The necessary file for
printing is not found.
Can not load pclradj.dll
Table file open error!! Check sum error!!
File ID not match!!
Table file read error!!
Error MessageCorrective ActionPossible Cause
BClose all applications
except for the one which
controls the printer, then
print it again.
BTurn off the computer,
then turn it on again.
Print the document
again. Unable to Allocate
Memory!!The memory for
printing is...

146
Care and Maintenance
Error messagePossible causeRecovery
Increase the hard disk
space.
If it is difficult to increase the
hard disk space or printing
error occurs even after
increasing the hard disk
space, change the spool
data format from EMF to
RAW by performing the
following steps.
However, RTA (Return To
Application: the length of
time between the start of
printing and the return of
control to an application) of
RAWis longer than that of
EMF.
1. Click Start, select
Settings, then click
Printers....

147
Error writing to
KXP8410GDI: for : The printer command
is invalid. Do you wish to
retry or cancel the job?
Care and Maintenance
Error messagePossible causeRecovery
Can not initialize ASPI for
Windows. Install newer
version of ASPI for
Windows.SCSI Board and its
driver are not installed
correctly.Correctly install SCSI board
and its driver. (Refer to the
instructions manual of the
SCSI board.)
Wnaspi32.dll will be
installed or replaced with a
new version.
For any other trouble related
to SCSI, refer...

148
Care and Maintenance
System Process-Out of
Virtual Memory 
Your system is running
low on virtual memory.
Please close some
applications. You can
then start the System
option in the Control
Panel and choose the
Virtual Memory button to
create an additional
paging file or to increase
the size of your current
paging file.Your system is running
low on virtual memory.Increase the virtual memory
by following the procedure
below.
1. Click Start, Settings,
then click Control Panel.
2. Double click the...

149
BThe printer was
turned on after
turning on the
computer.
BThe terminator
setting is improper.
BSCSI setting or
cable connection is
improper. The necessary file is
not installed in the
computer.
Error messagePossible causeRecovery
Care and Maintenance
Not Detect. Turn off the printer and the
computer, then turn them
on again. If the trouble still
remains, confirm the
following points.
BThe terminator is
correctly set.
BThe SCSI board is
correctly installed in the
computer.
BThe system is correctly...

150
Confirm that the SCSI
board is correctly installed
in the computer and it is
set correctly. (Refer to the
manual of the SCSI
board.) 
For any other trouble
related to SCSI, refer to
the SCSIsection of Care
and Maintenance 
( +P. 134). SCSI board is not set
correctly.
Unavailable LPT port is
selected when using
Windows 3.1. There isn’t available
LPT Port.
Error messagePossible causeRecovery
Care and Maintenance
SCSI device can not be
used. Because ASPI dll
file is not exist or
doesn’t match.SCSI board...