Panasonic Kx Nt321 Information Manual

Stand Usage
11 Document Version 2008-05
Stand Usa geAttaching the Stand
Place the catches (A) of the stand into hooks located in the unit. 
Gently push the stand in the direction indicated until it locks into 
place. The stand will be mounted in the high position.
Removing the Stand
Hold the stand with both hands.
Gently rotate the stand in the direction indicated until it is released.
Cabling
When using the stand, ensure that the cables are clamped as 
shown.
A
NT321M_QRG.fm  Page 11  Tuesday, January...

Stand Usage
12Document Version 2008-05
Adjusting from High to Low Position
Hold the stand with both hands as shown and gently push the stand 
in the direction indicated until it locks into the low position (B).
Adjusting from Low to High Position
Hold the stand with both hands as shown and gently pull the stand 
in the direction indicated until it locks into the high position (A).
A
NT321M_QRG.fm  Page 12  Tuesday, January 15, 2008  4:51 PM 

Wall Mounting
13 Document Version 2008-05
Wall Moun ting1.Remove the stand if it is attached. For information on removing the 
stand, refer to page 11.
2.Attach the wall mounting adaptor 
as shown.
•Make sure the cables are not 
pinched by the wall mounting 
adaptor. When running the cables 
from the top of the unit, look 
through the opening in the wall 
mounting adaptor to confirm that 
the cables are not being pinched.
•Slide the wall mounting adaptor in 
the direction indicated until it locks 
into...

Important Information
14Document Version 2008-05
Im p ort an t In fo rm at i onWhen using a KX-NT321 IP-PT, keep the following conditions in 
mind.
•If the unit does not operate properly, disconnect the unit from the 
Ethernet cable and then connect again.
•If you are having problems making calls, disconnect the Ethernet cable 
and connect a known working IP-PT. If the known working IP-PT operates 
properly, have the defective IP-PT repaired by an authorized Panasonic 
factory service center. If the...

Important Information
15 Document Version 2008-05
Placement 
1) Do not place heavy objects on top of this unit.
2) Care should be taken so that objects do not fall onto, and liquids are not 
spilled into, the unit. Do not subject this unit to excessive smoke, dust, 
moisture, mechanical vibration, shock or direct sunlight. 
3) Place the unit on a flat surface.
WARNING:TO PREVENT POSSIBLE FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE 
THIS UNIT TO RAIN OR MOISTURE.
THIS HANDSET EARPIECE IS MAGNETIZED AND MAY...

Important Information
16Document Version 2008-05
Important Safety Instructions
When using this unit, basic safety precautions, including those below, should 
always be followed to reduce the risk of fire, electric shock and injury to 
persons.
1.Read and understand all instructions.
2.Follow all warnings and instructions marked on this unit.3.Unplug this unit from the AC outlet before cleaning. Do not use liquid or 
aerosol cleaners. Clean with a damp cloth.
4.Do not use the unit near water, for example,...

Important Information
17 Document Version 2008-05
FCC Information
F.C.C. REQUIREMENTS AND RELEVANT INFORMATIONThis equipment has been tested and found to comply with the limits for a 
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are 
designed to provide reasonable protection against harmful interference in a 
residential installation.
This equipment generates, uses, and can radiate radio frequency energy 
and, if not installed and used in accordance with the instructions,...

Important Information
18Document Version 2008-05
Customer Information
This equipment complies with Part 68 of the FCC rules and the requirements 
adopted by the ACTA. On the bottom of the cabinet of this equipment is a 
label that contains, among other information, the following product identifier:  
US: ACJKXNANKX-NT321
 If requested, this number must be provided to the telephone company.
If trouble is experienced with this equipment KX-NT321, for repair or warranty 
information, please contact:...

Wall Mounting Template
19 Document Version 2008-05
Wall Mountin g Te mpla te
83 mm (3-1/4 in)  100 mm (3-15/16 in)
for base unit
One screw here
One screw at either point
WALL MOUNTING TEMPLATE
1. Drive the screws into the wall as indicated.
2. Hook the unit onto the screw heads.
Note:
Make sure to set the print size to correspond with 
the size of this page. If the dimensions of the paper 
output still deviate slightly from the measurements 
indicated here, use the measurements indicated 
here....

PSQX4664ZA-UU     KK0508YH0 (M) (Ver 0.02) Panasonic Consumer Electronics Company,
Division of Panasonic Corporation of North America
One Panasonic Way Secaucus, New Jersey 07094
Panasonic Puerto Rico, Inc.San Gabriel Industrial Park Ave. 65 de Infantería, Km. 9.5
Carolina, Puerto Rico 00985
http://www.panasonic.com/csd
Copyright:This material is copyrighted by Panasonic Communications Co., Ltd., and 
may be reproduced for internal use only. All other reproduction, in whole or in 
part, is prohibited...