Panasonic KX FLB758RU User Manual

4.3. PRINTING (PAPER PICK UP)
During printing 
     · 
  
  W hen the SOLENOID is turned ON, the HOOK GEAR FIX is hooked on the RING of GEAR CLUTC H. It causes the GEAR
PICKUP PAPER to rotate.
 
     · 
  
  Atthesametime,CAM ´s rotation lifts up the PLATE LIFT PAPER . The recording paper is pressed by the PICKUP ROLLER
and the top paper is separated and fed. Then the PLATE LIFT PAPER is pressed down.
 
  
  · 
  
  Even the SOLENOID is turned OFF, it can not stop on the way of a turn because the tip of...

4.4. SCANNING (ADF)
 
     · 
  
  DOCUMENT TRANS MISSIO N (ADF)
The tip of the document is sent to a point of contact between the separation roller and the separation pad through the
document feed roller, then the document is fed there separately. The document transference roller carries the document
and the CIS reads it through the glass. The document U-turns along the guide and is exited through the paper exit roller.
 
     · 
  
  DOCUMENT TRANS MISSIO N (SCANNER GLASS )
The CIS held in the CIS...

4.5. MAINTENANCE
If a black line, a white line or a dirty pattern appears on your recording paper, on your original, or on the fax document received
by the other party, clean the white plate, scanner glass and lower glass.
4.5.1. WHITE PLATE AND SCANNE R GLASS
1.
2.
3.Open the document cover.
Clean the white plate and scanner glass with a soft and dry cloth.
Close the document cover.
4.5.2. LOWER GLASS
Caution: 
     · 
  
  Be careful when handlin g the drum and toner unit.
 
  
  · 
  
  Do not use...

4.Clean the lower glass with a soft and dry cloth.
5.Reinstall the drum and toner unit by holding the tabs.
6.Close the printer cover, until locked, by pushing down on both sides.
7.Reconnect the power cord and the telephone line cord.
34
KX-FLB75 8RU
Downloaded From ManualsPrinter.com Manuals 

4.5.3. DOCUMENT FEEDER ROLLERS
If misfeeding of your original occurs frequently, clean the document feeder rollers.
1.Lift, and hold open the ADF cover.
2.Clean the document feeder rollers with a soft and dry cloth.
3.Close the ADF cover.
35
KX-FLB75 8RU
Downloaded From ManualsPrinter.com Manuals 

4.6. DOCUMENT JAMS
If the unit does not release the document during feeding , remove the jammed document as follows.
1.Lift, and hold open the ADF cover. 
     · 
  
  Do not pull out the jammed document forcibly before
lifting the ADF cover.
2.Remove the jammed document carefully.
 
     · 
  
  If you cannot remove the jammed document, open the
document cover, remove the document, then close the
document cover.
3.Close the ADF cover.
36
KX-FLB75 8RU
Downloaded From ManualsPrinter.com Manuals 

4.7. RECORDING PAPER JAMS
If the unit does not eject any recording paper during reception or copying , the recording paper has jammed and the display will
show the followin g massage.
The display will show the followin g.
1.Push the front cover open button then open the front cover.
2.W hen the recording paper has jammed near the drum and toner
unit:
Remove the jammed paper by pulling it toward you.
W hen the recording paper has jammed near the recording paper
exit:
Remove the jammed paper by pulling it...

3.Close the front cover, until locked, by pushing down on both
ends.
4.Remove the recording paper. Straighten and reinsert it into the
recording paper entrance.
38
KX-FLB75 8RU
Downloaded From ManualsPrinter.com Manuals 

5 DISASSEMBLY INSTRUCTIONS
5.1. UPPER MAIN CABINET SECTION
CROSS REFER ENCE:A1: HOW TO REMOVE THE PAPER TRAY, DOCUMENT COVER AND PAPER GUIDE (P.43)
A2: HOW TO REMOVE THE PRINTER COVER (P.44)
A3: HOW TO REMOVE THE PICK UP ROLLER ASS’Y (P.45)
A4: HOW TO REMOVE THE DUCT UNIT AND FAN MOTOR (P.46)
A5: HOW TO REMOVE THE BOTTOM PLATE (P.46)
A6: HOW TO REMOVE THE ANALOG BOARD AND LSU (P.47)
A7: HOW TO REMOVE THE DIGITAL BOARD AND MOTOR DRIVER BOARD (P.47)
A9: HOW TO REMOVE THE HEAT ROLLER AND EXIT ROLLER (P.50)...

5.2. LOWER MAIN CABINET SECTION
CROSS REFER ENCE:A1: HOW TO REMOVE THE PAPER TRAY, DOCUMENT COVER AND PAPER GUIDE (P.43)
A5: HOW TO REMOVE THE BOTTOM PLATE (P.46)
A6: HOW TO REMOVE THE ANALOG BOARD AND LSU (P.47)
A7: HOW TO REMOVE THE DIGITAL BOARD AND MOTOR DRIVER BOARD (P.47)
B1: HOW TO REMOVE THE POWE R BOARD, AND VARISTOR BOARD AND AC INLET (P.48)
B2: HOW TO REMOVE THE MAIN FRAME (P.48)
B3: HOW TO REMOVE THE REGISTRATION ROLLER (P.49)
B4: HOW TO REMOVE THE H.V.P.S (P.49)
B5: HOW TO REMOVE THE MOTOR...