Panasonic Kx Flb756 Operating Instruction Manual

							71
Operations
For fax advantage assistance, call 1-800-435-7329.
Copying
The unit does not make a copy.
 You cannot make a copy during
programming. Make the copy after
programming or stop programming.
A black line, a white line or a dirty pattern
appears on the copied document.
 The white plate, scanner glass or lower
glass are dirty. Clean them (p. 77–79).
The printing quality is poor.
 Some paper has instructions
recommending which side to print on. Try
turning the paper over. 
 You may have used paper with a cotton
and/or fiber content that is over 20%, such
as letterhead or resume paper. 
 The remaining toner is low. Replace the
toner cartridge (p. 73).
 We recommend you replace the drum unit
every third time you replace the toner
cartridge 
(p. 73). To check the drum life
and quality, please print the printer test list
(p. 80).
 The toner save mode of feature #79 is on
(p. 65).
 When you make a copy from
transparencies, be sure to use the scanner
glass. Place a blank sheet of paper on top
of the transparency, and leave the
document cover open during copying 
(p. 48).
Using an answering
machine
I cannot receive documents automatically.
 Your greeting message on the answering
machine is too long. Shorten the message
(to less than 10 seconds).
 The answering machine rings too many
times. Set to 1 or 2 rings.
I cannot receive voice messages.
 Check if the answering machine is turned
on and connected to the fax machine
properly (p. 44).
 Set the number of rings on the answering
machine to 1 or 2.
(continued)I cannot retrieve recorded voice messages
on the answering machine from a remote
location.
 You did not program your remote access
code into your fax machine correctly.
Program the same code that is
programmed on the answering machine
on the fax machine with feature #12 
(p. 62).
I pressed the remote access code to
access the answering machine remotely,
but the line was disconnected.
 The code may include “#” which is used
for certain features provided by telephone
companies. Change the code on the
answering machine to another code which
does not include “#”. Also change the code
of the fax machine with feature #12 (p.
62).
Callers complain that they cannot send a
document.
 Your answering machine has run out of
recording tape. Rewind the tape to record
messages.
 You set the answering machine to only
give a greeting message.
Multi-Function Station
I cannot open a TIFF file.
 You must change the compression format
of the file. 
Example: To convert an image using
Imaging for Windows.
1. Click[Start], point to [Programs]—
[Accessories], then click [Imaging].
2. Open the TIFF file that you cannot open
in [Multi-Function Viewer].
3. Select [Properties]from the [Page]
menu.
— The [Page Properties] dialog box
will appear.
4. Click the [Compression]tab, then
select [CCITT Group 3 (1d) Modified
Huffman] from the drop-down list.
5. Click[OK].
— The compression format of the file is
now changed.
[Launcher] disappears.
 Look in the tool bar. If you do not find the
[Launcher]icon, it is closed. If you do find
the icon, it is just minimized. Click the icon
in the tool bar.
ABC
OriginalCopy
(continued)
KX-FLB756 (066-072)  03.4.14  9:17 PM  Page 71 
						

							72
Operations
For fax advantage assistance, call 1-800-435-7329.
Multi-Function Station
(cont.)
I cannot recognize the last part of an entry
in the list of the [One Touch], [Directory],
[Journal] or [Caller ID].
 Put the cursor on the line between the
buttons. The cursor changes shape and
you can expand the area by dragging or
double-clicking.
When I exit Multi-Function Station, the
[Multi-Function Viewer] window does not
close.
 The[Multi-Function Viewer]window can
be operated separately. Click the [X]
button to close the window.
I cannot scan.
 When scanning at a high resolution, a
large amount of available memory is
required. If your PC warns of insufficient
memory, close all other applications and
try again.
 The fax machine is in use. Try later on.
 There is not enough space on the hard
disk. Delete unnecessary files and try
again.
 Restart the PC, and try again.
 Check the connection of the PC and the
fax machine (p. 50).
 You attempted to scan a document longer
than the paper size which you set in the
[Panasonic FLM551/FLB751 Series]
dialog box. Change the setting or divide
the document into the appropriate paper
size, and try again.
The document does not feed into the fax
machine.
 Remove the document and reinsert it.
Even after clicking [Cancel], scanning
continues.
 Please wait. It may take a while for the
cancel request to be accepted.
Multi-Function Station does not work
properly.
 Click the [X]button to exit Multi-Function
Station, and restart. If Multi-Function
Station still does not close, restart the PC.
 If you connect the USB cable to USB hub,
connect it to the USB port of your
computer directly.
 Confirm the BIOS setting of your
computer. For parallel connection, select
ECP, Bi-directional or an equivalent
parallel port mode. For USB connection,
select USB port mode. Please refer to
your PC operating instructions or consult
the manufacturer.
 If you have any other multifunction
software installed on your computer,
uninstall them.
I want to replace the parallel cable with a
USB cable and vice versa.
 You must change the printer properties.
1. Replace the cables.
2. Set the connection type (parallel or
USB) by using the fax machine
according to the cable type you use
(feature #15 on page 62).
3. Click [Start], point to [Settings], then
click [Printers].
4. Right-click [Panasonic FLM551/
FLB751 Series]and click [Properties].
— The [Panasonic FLM551/FLB751
Series Properties]dialog box will
appear.
5. Click the [Details](Windows 98/Me) /
[Ports](Windows 2000/XP) tab, select
the connection type, then click [OK].
— If Multi-Function Station does not
work correctly, uninstall the software,
then re-install it.
(continued)
If a power failure occurs!
 The unit will not function.
The unit is not designed for making emergency telephone calls when the power fails.
Alternative arrangements should be made for access to emergency services.
 Fax transmission and reception will be interrupted.
 If any fax documents are stored in the memory, they will be lost. When power is restored, a
power down report will be printed out stating which contents in the memory have been erased.
KX-FLB756 (066-072)  03.4.14  9:17 PM  Page 72 
						

							73
Replacement
For fax advantage assistance, call 1-800-435-7329.
When the display shows the following, replace the toner cartridge.
Display: or  
We recommend you replace the drum unit every third time you replace the toner cartridge.
To check the drum life and quality, please print the printer test list (p. 80).
To ensure that the unit operates properly, we recommend the use ofPanasonic toner cartridge
(Model No. KX-FA76) and drum unit (Model No. KX-FA77D). See page 8 for accessory
information.
 We cannot be responsible for any damage to the unit or degradation of print quality
which may occur from the use of non-Panasonic toner cartridge and drum unit.
Caution:
The drum unit contains a photosensitive drum. Exposing it to light may damage the drum.
Once you have opened the protection bag:
— Do not expose the drum unit to light for more than 5 minutes.
— Do not touch or scratch the green drum surface.
— Do not place the drum unit near dust or dirt, or in a high humidity area.
— Do not expose the drum unit to direct sunlight.
Do not unplug the fax machine to prevent loss of fax documents in memory.
 Do not leave the toner cartridge out of the protection bag for a long time. It will decrease
the toner life.
Do not pour any toner into the toner cartridge.TONER EMPTY
TONER LOW
Replacing the toner cartridge and the drum unit!
Printer 
cover
Printer cover 
open button
3
Press down the printer cover open button
then open the printer cover.
4
Tap on the used toner cartridge several
times to allow the remaining toner to fall
into the drum unit. Remove the drum and
toner unit by holding the two tabs.
 If you replace the toner cartridge and the
drum unit at the same time, skip to step 7.
Drum and 
toner unit
2
Remove the new toner cartridge from the
protection bag. Peel off the seal from the
toner cartridge.
New toner cartridge
Seal
1
Before opening the protection bag of the
new toner cartridge, shake it vertically 
at least 5 times.
(continued)
KX-FLB756 (073-079)  03.4.21  6:45 PM  Page 73 
						

							74
Replacement
For fax advantage assistance, call 1-800-435-7329.
7
If you replace the drum unit at the same
time, remove the new drum unit from the
protection bag. Remove the protection 
bar from the drum unit.
With “Panasonic” face up on the toner
cartridge, match the red arrows on the
cartridge and the drum unit.
Used toner cartridge12
Drum unit
Green drum surface
6
Pull up the right edge of the used toner
cartridge (
#). Remove the cartridge from
the drum unit (
$).
 The toner may stick to the cartridge and
the drum unit. Be careful when handling.
See page 5 for details.
 Do not drop the toner on the green drum
surface.
 Put the used toner cartridge into the
protection bag.
8
Slide the tab on the toner cartridge into
the slot of the drum unit.Tab
Slot
9a
Firmly press down on the right side of the
toner cartridge to snap into position and...
9b
turn the two levers on the toner cartridge
with firm pressure.
Levers
Protection bar
New drum unit
New toner 
cartridge 
Drum unit Hold here.
Red 
arrows
5
Turn the two levers on the used toner
cartridge firmly.
Levers
Used toner cartridge
Levers
KX-FLB756 (073-079)  03.4.21  6:45 PM  Page 74 
						

							75
Replacement / Jams
For fax advantage assistance, call 1-800-435-7329.
Recording paper jam!
1
Press down the printer cover open button
then open the printer cover. The display will show the following.
Display:PAPER JAMMED
Printer 
cover
Printer cover 
open button
When the recording paper has jammed in the unit
11
Install the drum and toner unit by holding
the tabs.
Drum and 
toner unit
12
Close the printer cover by pushing down
on both sides until locked.
Waste disposal method
 Waste material may be dumped or incinerated under
conditions which meet all country and local
environmental regulations.Printer 
cover
Lower glass
Caution:
Do not touch the bottom of this 
cover when cleaning the lower 
glass. It is very hot.
If the lower glass is dirty, clean it with
a soft and dry cloth.
10
The toner cartridge is installed when the
triangles match.
Triangles
(continued)
KX-FLB756 (073-079)  03.4.21  6:45 PM  Page 75 
						

							76
Jams
For fax advantage assistance, call 1-800-435-7329.
When the recording paper has jammed
near the recording paper exit (Fuser unit):
Remove the recording paper (#), then
remove the drum and toner unit to allow the
jammed paper to pull free from the rear
cabinet ($).
Remove the jammed paper from the fuser
unit by pulling it upwards carefully.
Drum and 
toner unit
#
$
Jammed paper
Caution:
Do not touch the bottom of this 
cover. It is very hot.
The display will show the following.
Display:
Remove the recording paper. Straighten and
reinsert it into the recording paper entrance.FAILED PICK UPRecording paper 
entrance
When the recording paper is not fed into the unit
properly
3
Close the printer cover by pushing
down on both sides until locked (#). 
Straighten and reinsert the recording
paper into the recording paper entrance
($).
Printer 
cover
#
Recording paper 
entrance
$
2
When the recording paper has jammed
near the drum and toner unit:
Remove the jammed paper carefully by
pulling it toward you.
Jammed paper
KX-FLB756 (073-079)  03.4.21  6:45 PM  Page 76 
						

							77
Jams / Cleaning
For fax advantage assistance, call 1-800-435-7329.
Document jams - sending!
1
Lift, and hold open the ADF cover.
 Do not pull out the jammed document
forcibly before lifting the ADF cover.
2
Remove the jammed document carefully.
 If you cannot remove the jammed
document, open the document cover,
remove the document, then close the
document cover.
Jammed 
document
ADF cover
3
Close the ADF cover.
White plate and glasses!
If a black line, a white line or a dirty pattern appears on your recording paper, on your original, or
on the fax document received by the other party, clean the white plate, scanner glass and lower
glass.
White plateDocument 
cover
Scanner
glass
1
Open the document cover.
2
Clean the white plate and scanner glass
with a soft and dry cloth.
White plate and scanner glass
3
Close the document cover.
Jammed 
document
Document
cover
ADF cover
KX-FLB756 (073-079)  03.4.21  6:45 PM  Page 77 
						

							78
Cleaning
For fax advantage assistance, call 1-800-435-7329.
1
Disconnect the power cord and the
telephone line cord.
2
Press down the printer cover open button
then open the printer cover.
3
Remove the drum and toner unit by holding
the two tabs.
4
Clean the lower glass with a soft and dry
cloth.
Printer 
cover
Printer cover 
open button
Caution:
 Be careful when handling the drum and toner unit. See the caution for the drum unit on
page 73 for details.
 Do not use paper products, such as paper towels or tissues, to clean the inside of the
unit.
The area near the lower glass is hot. We recommend to clean the lower glass after
the unit cools.
5
Reinstall the drum and toner unit by
holding the tabs.
Drum and toner unit
Lower glass
Power cordTelephone line cord
Drum and 
toner unit
Lower glass
Caution:
Do not touch the bottom of this cover 
when cleaning the lower glass. It is 
very hot.
KX-FLB756 (073-079)  03.4.21  6:45 PM  Page 78 
						

							79
Cleaning
For fax advantage assistance, call 1-800-435-7329.
6
Close the printer cover by pushing down
on both sides until locked.
7
Reconnect the power cord and the
telephone line cord.
Printer 
cover
Power cord
Telephone line cord
ADF cover
ADF cover
3
Close the ADF cover.
2
Clean the document feeder rollers with a soft
and dry cloth.
Document 
feeder rollers
1
Lift, and hold open the ADF cover.
Document feeder rollers!
If misfeeding of your original occurs frequently, clean the document feeder rollers.
KX-FLB756 (073-079)  03.4.14  9:18 PM  Page 79 
						

							80
Printed Reports
Reference lists and reports!
STOP
SET
MENU
1
Press prepeatedly until the following
is displayed.
Display:
2
Press (or )until the desired item is
displayed.
3
Press wto start printing.
 To stop printing, press {.
After printing, the printed item will be
displayed.
4
Press p.PRINTING
CALLER ID LIST
PRESS SET
PRINTER TEST
PRESS SET
BROADCAST LIST
PRESS SET
JOURNAL REPORT
PRESS SET
TEL NO. LIST
PRESS SET
SETUP LIST
PRESS SET
PRINT REPORT
PRESS NAVI.[
IH]
You can print out the following lists and reports for your reference.
Setup list:provides you with the current settings of the basic and advanced programming
features (p. 61–65).
Telephone number list:provides you with names and telephone numbers which are stored in
one-touch dial and navigator directory. 
Journal report:keeps records of fax transmission and reception. This report will be printed
automatically after every 30 fax communications (feature #22 on page 63).
Broadcast programming list:provides you with entries which are stored in the broadcast
feature (p. 36).
Printer test list:allows you to check the print quality of your unit. If the test print has a dirty
pattern, or blurred points or lines, clean the lower glass (p. 78). If printing quality is still poor,
replace the toner cartridge and drum unit.
Caller ID list:keeps records of the last 30 callers after subscribing to a Caller ID service. This
report will be printed automatically after every 30 callers (feature #26 on page 64).
KX-FLB756 (080-085)  03.4.14  9:19 PM  Page 80