Panasonic Iris Reader Bm Et200 Operating Instructions

							61
No.Procedure
Press [+] [0] [3] [enter].
The short electronic sound PiPi is heard.
Enter one of the following.
English:
Press [0] [1] [enter]
Japanese:
Press [0] [2] [enter]
German:
Press [0] [3] [enter]
French:
Press [0] [4] [enter]
Italian:
Press [0] [5] [enter]
Spanish:
Press [0] [6] [enter]
Russian:
Press [0] [7] [enter]
Chinese:
Press [0] [8] [enter]
Korean:
Press [0] [9] [enter]
Arabic:
Press [1] [0] [enter]
Portuguese:
Press [1] [1] [enter]
Turkish:
Press [1] [2] [enter]
Dutch:
Press [1] [3] [enter]
Swedish:
Press [1] [4] [enter]
The voice guidance will say, Registration has been completed. in the selected lan-
guage.
Note:When the voice guidance will say, Registration has been failed. , retry Step 2.
1
2
accept reject
accept reject
accept reject
Select a Guidance Language
The following is how to select a language of the voice guidance. 
						

							62
Select the Recognition Method
The following is how to select the recognition method.
No.Procedure
Press [+] [0] [8] [enter].
The short electronic sound PiPi is heard.
Select the recognition method.
•When performing iris recognition only, press [0] [enter].
•When performing iris recognition and PIN recognition, press [1] [enter].
The voice guidance will say, Registration has been completed.
Note:When the voice guidance says, Registration has been failed., retry Step 2.
1
2
accept reject
accept reject
accept reject 
						

							63
Setup (Network Mode)
This section describes the settings of network mode.
The administration software is used for setup.
Refer to BM-ES200 Operating Instructions (supplied to Administration Software BM-ES200) for details on network mode opera-
tion.
Connection and Setup Flow
Connection and setup are performed before the iris reader is used in the network mode.
Detach the front cover from the iris reader. (Refer to p. 28.)
Make sure that the power is not supplied to the iris reader.
Perform the setup switch setting.
Set the operation mode to the network mode.
Attach the front cover to the iris reader. (Refer to p. 31.)
Supply the power to the iris reader.
Perform the following settings using the web browser on the PC.
•Register administrators. (Refer to p. 64.)
•Set up the iris reader. (Refer to p. 65.)
1
2
3
4
5
No.Procedure
1 ON
2 4 56783
Set according to operations. 
						

							64
Registering Administrators
The following are descriptions of how to register administrators in the network mode. In the network mode, registration of at
least one administrator is required. In the factory default setting, there are no administrators. At the time of initial setup, surely
register an administrator. Up to three administrators can be registered.
Reader ID: 1
IP Address: 192.168.0.3
Server IP Address: 192.168.0.2
Subnet Mask: 255.255.255.0
Gateway IP Address: No setting
Refer to p. 43 for how to register administrators.
Notes:
•In the network mode, registration of users with the operator’s privilege is not required.
•When changing the reader ID from the factory default setting, refer to p. 65.
Setup from the Web Browser on the PC
In the network mode, iris reader setup is available from the web browser.
Notes:
•Web browser control is available by administrators only.
•Other settings are performed using the administration software. (Refer to BM-ES200 Operating Instructions.)
Displaying the Setup Menu
Operations are same as the stand-alone mode. Refer to p.
37.
After login, the following page will be displayed. 
						

							65
About the Operation Window
[Reader Setting] button
Click this button to display the Reader Setting page.
The reader ID settings and the network settings can be
configured on the Reader Setting page.
[Administrator] button
Click this button to display the Administrator List page.
It is possible to check or register the administrator informa-
tion on the Administrator List page.Main area
Pages of each setup menu will be displayed.
[Reader ID] [IP Address]
Refer to p. 52.
[Server IP Address]
Enter the IP address of iris server as nnn.nnn.nnn.nnn.
Available value for nnn: 0 to 255
Default:192.168.0.2
Note:“nnn.nnn.nnn.255” is unavailable.
[Subnet Mask] [*Gateway IP Address]
Refer to p. 52.
Configure the Settings Relating to System [Reader Setting]
Click the [Reader Setting] button to display the Reader Setting page.
Configure reader ID settings and the network settings on this page.
[Reader Setting] button
[Administrator] button
Main area 
						

							66
Register administrators [Administrator List]
Click the [Administrator List] tab button to display the
Administrator List page.
Up to three administrators can be registered.
Step 1
Click the [New] button.
→The Administrator screen is displayed.
Step 2
Complete each setting item displayed in the frame on the
right of the window.
Notes:
•Refer to p. 42 for details on setting items.
•In the network mode, iris registration by the web brows-
er control is unavailable.
Step 3
Click the [Register] button.
→The administrator data is registered.
Note:
Click the [Cancel] button to cancel registration.
Check the Administrator List [Administrator]
Click the [Administrator] button to display the Administrator List page.
It is possible to check the administrator information on this page.
[New] button [No.] [User ID] [Delete] button [Details]
button
Refer to p. 43. 
						

							67
Instructions for Proper Enrollment and Recognition
You (user) should follow the instructions mentioned in this page for proper enrollment and recognition.
• Open your eyes as wide as you can so as not to hide the irises with eyelids and eyelashes.
• For users wearing glasses/sunglasses (for enrollment)
Take off the glasses when enrolling the iris data.
• For users wearing glasses/sunglasses (for recognition)
With this iris reader, you can carry out iris recognition wearing glasses. However, in the following cases, you should take off
the glasses or move the front panel to adjust the eye position in the mirror.
•Take off the sunglasses whose lens color is dark.
•When smudges are on the lenses, it may cause invalid iris
image capturing. In this case, wipe the lenses with a cloth.
•When light is reflecting on the lenses, it may cause invalid
iris image capturing. In this case, move your face or the iris
readers front panel upward or downward to avoid reflec-
tion. If you still cannot recognize yourself, take off your
glasses/sunglasses.
• If you are wearing contact lenses:
With this iris reader, you can carry out iris enrollment/recognition wearing contact lenses. However, if a lens has slipped off
the eyes corneal surface, the contact edge may hide the iris images. That may cause invalid recognition. In this case,
move the contact lens back to the corneal surface by blinking, or carry out enrollment after removing the contact lenses.
• Follow the distance indicator and voice guidance by moving slowly.
If you move so fast that your iris image cannot be captured properly, it may cause invalid recognition. Move as slowly as
you can when following the distance indicator and voice guidance.
Not preferable Preferable
Not preferable 
						

							68
Operating Procedures (Instructions for Users)
How to Position Your Eyes in the Mirror
This iris reader captures the iris data of both eyes at one time. If the eyes are not positioned within the capturing range, enroll-
ment/recognition will be invalid. Before enrollment/recognition, you (the user) should stand in front of the iris reader as follows
and adjust your eye position. Even when you carry out enrollment/recognition while sitting, you should adjust your eye position
in the same way.
Note:If your eye position is higher than the upside limit, bend down. If your eye position is lower than the upside limit, get on a
pedestal, etc.
Stand where you can see the iris reader from the
front side.
Stand where you can hold the tilt handles with your
arms bent moderately. If you are standing within the
recognition range, the distance indicator will light up at
the center of the mirror.
Notes:
•The recognition range is within approx. 30 cm to
40 cm {0.98 ft. to 1.32 ft.} away from the iris reader.
•The recognition area differs depending on users.
However, the approximate recognition area is
where you can stand holding the tilt handles with
your arms bent moderately.
Make sure that you can see either eye in the mirror.
When the eyes are not positioned in the mirror, move to the point where you can see the eyes in the mirror or adjust
the angle of the front panel by holding the tilt handles. Hold the tilt handles at the sides of the front panel.
Keep bending your arms moderately while holding the
handles.
1
3
2
No.Procedure
45°
Mirror
Distance between 
the eyes and mirror:
approx. 30 cm to 40 cm
{0.98 ft. to 1.32 ft.}
Tilt handles
Front panel
(Avoid hiding with 
a hand or cloth, etc.) Eye image capturing cameras
(Avoid hiding with a hand 
or cloth, etc.) 
Caution:Take care not to pinch your hands or fingers
between the front panel and the body of this appliance. 
						

							69
Open your eyes widely and look at the mirror from
the front side.
Open your eyes as wide as you can so as not to hide
the irises with eyelids and eyelashes.
Adjust your eye position by following the
distance indicator or voice guidance from the
speaker.
The distance indicator consists of five lamps. When a
user comes to the position that is most suitable for
capturing, all the five lamps light up. The number of
lighting lamp decreases when the distance between
the iris reader and you is closer. When the distance
between the iris reader and you is too short, the right
end lamp lights up.
4
5
No.Procedure
Not preferable Preferable
reject accept
Distance between the
iris reader and you
Too close
Suitable
Far
Too farNumber of
lighting lamp
1
5
4
3
2
1
0Voice guidance
Please move
back a little.
–
Please move a
little closer.
If You Have Difficulty in Eye Positioning
When trying the procedure of How to Position Your Eyes in the
Mirror (p. 68), you may sometimes have difficulty in positioning
the eyes in the mirror. In this case, cover either eye and position
your opened eye over an eye image capturing camera.
Note:Even if you carry out one-eye adjusting, capture left and
right eye separately to enroll both eyes.
If You are Wearing an Eyepatch, etc.
Enrollment/recognition using one eye capturing is available when you cannot have both eyes captured, due to an eyepatch,
etc. In this case, the voice guidance or distance indicator will lead you to position your opened eye over an eye image captur-
ing camera. (Refer to the illustrations in If You Have Difficulty in Eye Positioning.) Position your eye on the eye image captur-
ing camera, according to the guidance.
Left eye image
Eye image capturing camera (Left)
reject accept
Right eye image
Eye image capturing camera (Right)
accept reject 
						

							70
Move your position slowly by following the distance indicator or voice
guidance.
•When the distance between the iris reader and you is too far, the voice guidance
will say, Please move a little closer.
•When the distance between the iris reader and you is too short, the voice guidance
will say, Please move back a little.
5
accept reject
accept reject
Cases of Enrollment/Recognition Failure
•You have closed your eyes or not opened your eyes widely enough during the capturing procedure.
•You were wearing sunglasses whose lens color is too deep to be captured
•There were smudges on the glasses.
•You were not looking at the mirror during capturing.
•Your position is too near or too far away to be captured.
When you come within approx. 50 cm {1.64 ft.} of the iris reader, the guidance will start. The recognition range between the
eyes and mirror is approx. 30 cm to 40 cm {0.98 ft. to 1.32 ft.}.
How to Carry Out Enrollment (Network Mode)
The following is how to control the iris reader when your (the users) iris data is enrolled in the iris server.
Notes:
•Follow the direction of system administrators or operators when you carry out enrollment.
•In some cases, you may need to retry capturing when enrolling your iris data.
Wait until you can confirm the capturing result.
•Depending on the settings by the system administrators, voice guidance may not be output.
•The iris reader transfers the data to the iris server. Then, the data is enrolled in the iris server. If there are no suitable
images, the iris server will display the message to the system administrators or operators that the user needs to retry the
capturing procedure.
System administrators or operators should configure the data in the iris server, which is required for enrollment, and direct a
user to carry out enrollment. Users (you) should control the iris reader as follows, directed by system administrators or opera-
tors.
Stand (Sit down) in front of the iris reader.
Follow the directions of system administrators or operators.
If you are wearing glasses/sunglasses, take them off.
Follow the directions of system administrators or operators to start iris
image capturing.
•The voice guidance will say, Please look into the mirror. Please open your eyes
wider.
•The distance indicator or voice guidance will start.
Position your eyes in the mirror by referring to How to Position Your
Eyes in the Mirror (p. 68).
1
2
3
4
No.Procedure
accept reject
accept reject