Panasonic Indoor Pan Tilt Head Aw Ph400 Operating Instructions

Pan/Tilt Head Controller  AW-RP400
30 (E)
ENGLISH
Example of rack mounting
$How to mount the AW-RP400 in a rack
AW-RP400
1Use the accessory mounting screws (M4!8 mm) to attach the rack-mounting adaptors.
Rack-mounting adaptor
Accessory mounting
screws (M4!8 mm)
4 pcs 

Pan/Tilt Head Controller  AW-RP400
31 (E)
Example of rack mounting
$How to change the direction of the connector panel
1Remove the five bottom panel screws, and remove the
blank panel.
2Remove the five rear panel screws, and remove the
connector panel.
3Secure the connector panel to the bottom panel using the
screws.
4Secure the blank panel to the rear panel using the
screws.
Screws!5 (bottom panel)
Screws!5
(rear panel)
Screws!5 (bottom panel)
Screws!5
(rear panel) Remove the blank
panel.
Remove the...

Pan/Tilt Head Controller  AW-RP400
32 (E)
ENGLISH
Example of rack mounting
$How to replace the zoom switch
1Remove the four screws that secure the zoom lever.
2Pull out the zoom lever, disconnect the two cables from
the circuit board inside, and remove the zoom lever.
3Plug the two cables extending from the zoom switch into
the connectors on the circuit board inside.
4Secure the zoom switch using the four screws.
Screws!4
Screws!4 

Pan/Tilt Head Controller  AW-RP400
33 (E)
Replacing the consumable parts
The joysticks and zoom switch are consumables.
Replace them if they are not working properly.
Ask your dealer to do the replacement work. 

Pan/Tilt Head Controller  AW-RP400
34 (E)
ENGLISH
Specifications
Input connectors
DC 12V IN: XLR, 4 pins
CONTROL IN FROM ROP: D-SUB 15-pin, cable supplied with AW-CB400 remote operation panel
CONTROL IN FROM RCB: 10-pin round connector, cable supplied with WV-CB700A
EXT CONT IN: RJ45, additional AW-RP400 control signal input; 10BASE-T straight cable (UTP category 5),
max. 500 meters
REMOTE: 50-pin D-SUB connector, external control input, AW-CA50T9
Output connectors
CONTROL OUT TO 
PAN/TILT HEAD: RJ45,...

Cable Compensator  AW-RC400
35 (E)
Introduction
Accessories
≥The AW-RC400 is capable of providing cable
compensation for analogue composite, analogue Y/C or
analogue component signals in five channels up to 500
meters (when the 5C-2V connecting cable or its
equivalent is used).
≥It features a 5us advance function for the sync signals in
order to provide easy support for a system (another cable
compensator is required) in which the coaxial cable
connected between this AW-RC400 cable compensator
and the...

Cable Compensator  AW-RC400
36 (E)
ENGLISH
Parts and their function
1Power LED
This lights up green when the (2) POWER switch is set
to ON while a DC 12V voltage is supplied to the (7) DC
12V IN socket.
2POWER switch
Set this to ON to turn on the cable compensator’s power.
Part of the power supply circuitry will still operate even
when the power switch is at the OFF position. To turn off
the power completely, disconnect the AC adaptor.
3Cable length setting switches [0 to 5]
Set these switches according...

Cable Compensator  AW-RC400
37 (E)
Parts and their function
;MONITOR1, 2 connectors
The video signals of the cameras selected by the 
AW-RP400 pan/tilt head controller or the AW-CB400
remote operation panel which is connected to the 
AW-RP400 are output from these connectors.
The output signals are cable-compensated signals of the
same type as the input signals. For instance, if a channel
to which composite signals have been input is selected,
these composite signals will be cable-compensated and...

Cable Compensator  AW-RC400
38 (E)
ENGLISH
Example of rack mounting
$How to mount the AW-RC400 in a rack
Use the accessory rack-mounting adaptors and accessory
mounting screws (M4!8 mm) to mount the unit in a rack.
1Press the POWER switch to turn off the power.
2Remove four feet on the bottom of the unit.
3Place the rack-mounting adaptors to the both ends of the
unit, and fix it using four mounting screws.POWER switch
Remove four feet.
Rack-mounting adaptor
Mounting
screws 

Cable Compensator  AW-RC400
39 (E)
Specifications
Input connectors
DC 12V IN: For connecting accessory AC adaptor (AW-PS301)
G/L IN: BNC!2, automatically terminated by 75-ohm resistance, loop-through output, black burst
VIDEO/Y, Pr/C, Pb: BNC!3 (5 sets), 75-ohm termination
Composite  1 Vp-p
Y/C
Y: 1 Vp-p (with sync)
C: 0.286V (burst)
Component
Y: 1 Vp-p (with sync)
Pr, Pb: 0.7Vp-p
MONI SEL IN: RJ45
Connecting cable: 10BASE-T straight cable (UTP category 5), max. 50 meters
Output connectors
G/L OUT:...