Panasonic Indoor Pan Tilt Head Aw Ph400 Operating Instructions

Before attempting to connect, operate or adjust this product, 
please read these instructions completely.
AW-PH400
AW-RC400AW-RP400
AW-RL400
Before attempting to connect, operate or adjust this product, 
please read these instructions completely.
Indoor Pan/Tilt HeadAW-PH400
Pan/Tilt Head ControllerAW-RP400E
Cable CompensatorAW-RC400E
Roll UnitAW-RL400G
ESPAÑOL
ENGLISH
DEUTSCH
FRANÇAIS
ITALIANO 

1(E)
Safety precautions
1indicates safety information.
$DO NOT REMOVE PANEL COVER BY
UNSCREWING.
To reduce the risk of electric shock, do not remove
cover. No user serviceable parts inside.
Refer servicing to qualified service personnel.
WARNING:
TO REDUCE THE RISK OF FIRE OR SHOCK
HAZARD, KEEP THIS EQUIPMENT AWAY
FROM ALL LIQUIDS-USE AND STORE ONLY
IN LOCATIONS WHICH ARE NOT EXPOSED
TO THE RISK OF DRIPPING OR SPLASHING
LIQUIDS, AND DO NOT PLACE ANY LIQUID
CONTAINERS ON TOP OF THE EQUIPMENT.
CAUTION:
TO...

2(E)
ENGLISH
Contents
Safety precautions  ........................................................... 1
Precautions for use  .......................................................... 3
Introduction ...................................................................... 4
Accessories ...................................................................... 4
Precautions for use  .......................................................... 4
Installation precautions...

3(E)
Precautions for use
≥Handle the ROP carefully.
Dropping the ROP or subjecting it to strong impact may give rise to malfunctioning or accidents.
≥Use the ROP in an ambient temperature of –10°C to +45°C.
Using the ROP in cold places below –10°C or hot places above 45°C may adversely affect its internal parts.
≥Turn off the power before connecting or disconnecting the cables.
Be absolutely sure to turn off the power before connecting or disconnecting the cables.
≥Avoid using the units outdoors....

Indoor Pan/Tilt Head  AW-PH400
4(E)
ENGLISH
Introduction
Accessories
Precautions for use
≥The stand-alone compact pan/tilt head can be rotated
through 190 degrees in the vertical direction and 400
degrees in the horizontal direction.
≥Operations can be performed at high speeds of up to 90
degrees per second.
≥Equipment such as a camera and lens with a total weight
of 8 kg can be mounted on the unit.
≥The camera can also be rotated using the AW-RL400 roll
unit available as an option.
≥The shooting...

Indoor Pan/Tilt Head  AW-PH400
5(E)
Installation precautions
≥Do not install the unit on any of its sides.
≥Avoid using the unit in the kitchen and other locations with lots of steam and oily vapors.
≥Mount the camera on the pan/tilt head only when you have finished installing it.
≥The maximum load-bearing capacity of this unit is 8 kg.
It cannot be used if the load to be borne exceeds 8 kg.
≥Do not use a lens which will impair or upset the unit’s balance. 
Even if the load borne by the unit is less than...

Indoor Pan/Tilt Head  AW-PH400
6(E)
ENGLISH
Parts and their function
16
7
8
9
5 2
3
4
:;<
=
>
? 

1Rotary head
This rotates in the horizontal direction.
2Pedestal
3POWER ON/OFF switch
When this is set to ON, the unit’s power is turned on;
when it is set to OFF, it is turned off.
4AC 100 inlet [AC IN] (AC 3-point inlet)
Connect the accessory AC power cable to this inlet.
5Camera mounting base mounting screws
M5!20 mm hexagon socket head screws, M5 flat
washers (3 of each provided as accessories)
These parts are used to secure the camera mounting
base to the rotary arm.
6Tally lamp (accessory)
This is...

=Guide pin
Use this to determine the direction in which the camera is
to be mounted.
>Camera mounting screws (U1/4” 20UNC)
These are used to secure the camera firmly after it has
been mounted.
?Side blank panel
This is used when the mounting direction of the pedestal
connector panel is to be changed.
@SDI IN connector [SDI IN]
Use a coaxial cable to connect this to the SDI OUT
connector on the AW-PB504 SDI card or other card
installed in the convertible camera.
AENG LENS CONTROL connector 
[ENG LENS...

Indoor Pan/Tilt Head  AW-PH400
9(E)
Parts and their function
JY connector [Y]
This is the output connector for the camera’s video
signals.
It is connected to the Y/VIDEO connector on the 
AW-RC400 cable compensator or monitor, etc.
Use a BNC coaxial cable for the connecting cable.
The AW-PB302 RGB card must be installed if the 
AW-E300, AW-E300A, AW-E600, AW-E800 or 
AW-E800A convertible camera is to be used.
K1394 connector [1394]
This is used for the control of the convertible camera and
pan/tilt head...