Panasonic Indoor Pan Tilt Head Aw Ph360n Operating Instructions

- 41 -
Connections
?When the unit is to be connected by a network, and the camera and pan/tilt head are to
be controlled by a personal computer
• Use the pan/tilt head cable (AW-CA50F29) to connect the unit with the convertible
camera containing the plugged-in WEB card.
• Set controller selection switch SW1 to the right side (RP501), and select the
transmission signal selection setting that supports the WEB card.
• Use a 10BASE-T straight cable (UTP category 5) to connect the unit connector with
the...

- 42 -
Connections
@When the unit is to be connected to a personal computer using the IEEE1394 cable, and
the camera and pan/tilt head are to be controlled by the personal computer
• Use the pan/tilt head cable (AW-CA50E29) to connect the unit with the convertible
camera containing the plugged-in IEEE1394 card.
• Set controller selection switch SW1 to the right side (RP501), and select the
transmission signal selection setting that supports the analog/IEEE1394 card.
• Use the IEEE1394 cable to connect...

- 43 -
Be absolutely sure to set the limiters (travel range) of the pan/tilt head before use.
Depending on where the pan/tilt head system has been installed, obstacles may be
present within the travel range with which the camera may come into contact. Contact with
any such obstacle by the camera may cause malfunctioning or accidents.
In this case, contact can be prevented by setting the limiters directly before any such
obstacle.
The controller is used to set the limiters.
The positions of four limiters...

- 44 -
$Setting/releasing the limiters
OFor the controller AW-RP301/AW-RP305/AW-RP501/AW-RP505
1.To set the upper limit position of the
travel range:
Using the controller, tilt the camera to
the position which is to serve as the
upper limit.
While holding down the MEMORY button
on the controller, press PRESET button
2 and PRESET button 3 simultaneously
for at least 5 seconds.
The setting is completed as soon as the
lamp of the PRESET button 5 comes on.
To release the setting:
While holding down the...

- 45 -
Limiters
OFor the controller AW-RP605A
1.To set the upper limit position of the
travel range:
Using the controller, tilt the camera to
the position which is to serve as the
upper limit.
While holding down the OK button on
the controller, press TRACING/PRESET
MEMORY button 47 .
The setting is completed as soon as the
lamp of the TRACING/PRESET
MEMORY button 41 [LIMIT ON] comes
on.
To release the setting:
While holding down the OK button on
the controller, press TRACING/PRESET
MEMORY button 47 .
The...

- 46 -
1.To set the upper limit position of the
travel range:
Using the controller, tilt the camera to
the position which is to serve as the
upper limit.
While holding down the MENU/LIMIT
button on the controller, press PRESET
MEMORY button 15 .
The setting is completed as soon as the
lamp of the PRESET MEMORY button
45 comes on.
To release the setting:
While holding down the MENU/LIMIT
button on the controller, press PRESET
MEMORY button 15 .
The setting is released when the lamp of
the PRESET MEMORY...

- 47 -
Replacement of consumable parts
$ Replacing the battery
The battery lasts for about 5 years.
The pan/tilt head stores the preset
positions, limiter positions and other data in
its memory. Although this data is retained
even after the power has been turned off, it
will be lost when the power is turned off
once the battery has reached the end of its
service life.
Replace the battery once it has lost its
effectiveness. (The pan/tilt head uses a
CR2032 manganese dioxide-lithium
battery.)
Removing the...

- 48 -
Specifications
Power supply:DC +12 V (connector)
Power consumption:DC +12 V 3 A (camera power included),
DC +12 V 1.3 A (pan/tilt head only)
1indicates safety information.
Genlock input:Black burst or composite video (BNC connector)
Camera video output:Video: 75 Ω(BNC connector)
Y: 75 Ω(BNC connector)
Pr: 75 Ω(BNC connector) (Switchable to SDI)
Pb: 75 Ω(BNC connector)
SDI: BNC connector (Switchable to Pr)
Camera / pan/tilt head control:
• Controller (AW-RP301/AW-RP305)
Pan/tilt head control:...

- 49 -
Specifications
Allowable operating humidity:
Max. 90%
Dimensions (W!H!D):5 1
/8˝!9 5
/8˝!7 9
/16˝ (130!244!192 mm)
Weight:Approx. 7.7 lb (3.5 kg)
Finish:AV ivory paint (color resembling Munsell 7.9Y 6.8/0.8)
$Functions/performance
Tilt range:190 degrees (approx. ±95 degrees)
Tilt range may be subject to restrictions depending on the
mounted camera cable, lens, etc.
Panning range:300 degrees (approx. ±150 degrees)
Maximum operating speed:30 degrees/sec. for panning, 25 degrees/sec. for tilting...