Panasonic Indoor Pan Tilt Head Aw Ph360n Operating Instructions

0ºs8F
	{
†Ì	{
AW-PH360N
-	Â	{xz
žc®S
M	Í[Ô~
b
3ʯswGÖ›S¬
TŠwOQzS	!Z	“Xi^M{

a
jøxz
¼íg	Í	OAs‹wpb{S
M	Í[wMxz

a
¼Š.q-	Â	{w
a
jø›S¬TŠXi^M{
-	Â	{4
Ç
]–;
²t\w	{
†Ì	{›‘XS¡ˆwOQz
Y`XS–MXi^M{
fwKqG
~t-`z˜T’sMqVx6¡`oXi^M{
:
@
725#
Indoor Pan/Tilt Head
AW-PH360N
Before attempting to connect, operate or adjust this product, 
please read these instructions...

2
O
	ÍQ
ÇZw	–s8Fpb{
O
§Ýåqèï¶ù˜doz
ï	O”µ‡p
eLpV‡b{
O
¯ïÄé”å”831z831z
831z831z831z
831zÍ”¹Æç¯ïÐá”»”
p¯ïÄé”çpV‡b{O

›zÓæ·¿ÄÝÞæ”q`oJåpV‡
b{


- 3 -
1indicates safety information.
FCC Note:
This device complies with Part 15 of the FCC Rules. To assure continued
compliance follow the attached installation instructions and do not make any
unauthorized modifications.
This equipment has been tested and found to comply with the limits for a class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment....

- 4 -
OThis is a compact stand-alone type of
pan/tilt head which is capable of rotating
95 degrees upward and downward and
300 degrees on the horizontal.
OThis pan/tilt head can bear a total weight
of up to 8.8 lb (4 kg) for the camera and
lens combined.OThe pan/tilt head can be controlled using
the controllers AW-RP301, AW-RP305,
AW-RP501, AW-RP505, AW-RP605A,
AW-RP400 or a personal computer.
OThe positions and settings for shooting
up to 50 points can be entered as data
into the preset memory.
Camera...

- 5 -
ODo not install the pan/tilt head on any of its sides.
OAvoid using the pan/tilt head in kitchens or other places where there is excessive steam
and oil fumes.
OMake sure that the installation of the pan/tilt head has been completed before mounting
the camera onto it.
OThis pan/tilt head has a maximum load capacity of 8.8 lb (4 kg).
Do not use it for loads over 8.8 lb (4 kg).
ODo not use a lens that will cause the camera to be poorly balanced. Such a lens should
not be used even if the load...

- 6 -
Precautions for use
OIn order to protect the environment when the pan/tilt head is to be discarded at the end
of its service life, ask a specialized contractor to dispose of it properly.
OThis pan/tilt head uses a manganese dioxide-lithium battery (CR2032).
Be absolutely sure to remove this battery when disposing of the pan/tilt head or printed
circuit boards.
Be sure to dispose of any batteries removed according to the applicable regulations of
the country concerned.
Do not dispose of this type of...

- 7 -
Parts and their functions 

- 8 -
Parts and their functions
1Tilting arm
This tilts in the vertical direction.
2Tilting arm fixing screws
M4!12 mm (4 screws supplied)
3Camera mounting plate
This is used to mount the convertible
camera.
4Guide screws
These are used to maintain the
camera’s balance and anchor the
camera mounting plate.
5Guide pin
This determines the mounting direction
of the camera.
6Guide roller
This serves as the fulcrum for
maintaining the camera’s balance.
7Camera mounting screws
(U1/4˝-20 UNC)
These are used to...

- 9 -
Installation (The installation work must be performed by your dealer without fail.)
Stand-alone installation Suspended installation
Tilting Arm
$Assembling the pan/tilt head
Be absolutely sure to hold the pan/tilt head by the base when handling it.
OAttaching the tilting arm
Use the tilting arm fixing screws to attach the tilting arm. The way in which the arm is
mounted differs depending on the direction in which it is installed. (See the figure below.)

Tighten up the screws securely to ensure...

$Controller selection switch / installation direction switch /
landing characteristics settings
The following switches are set when determining controller selections, stand alone
settings and landing characteristics settings.
(RP501 / suspended installation / soft landing are the default settings.)
1. Remove the four head cover screws, and remove the cover slowly. (Take care not to
disturb the tally LED lamp wiring connections when removing the cover.)
2. Set the SW1, SW2 and SW4 switches on the front...