Panasonic Indoor Pan Tilt Head Aw Ph360n Operating Instructions

- 31 -
Connections
5When the camera and pan/tilt head are to be controlled by the AW-RP505 control panel
for transmitting component signals
• Use the supplied camera cable to connect the unit with the convertible camera.
• Set controller selection switch SW1 to the right side (RP501), and select the transmission
signal selection setting that supports the analog/IEEE1394 card.
• Use a 10BASE-T straight cable (UTP category 5) to connect the unit’s CONTROL IN IP/RP
connector with the multiport hub’s...

- 32 -
Connections
6When the camera and pan/tilt head are to be controlled by the AW-RP505 control panel
for transmitting SDI signals
• Use the supplied camera cable to connect the unit with the convertible camera containing the
plugged-in SDI card (such as the AW-PB504N).
• Use a coaxial cable to connect the SDI card’s SDI OUT connector with the unit’s SDI IN
connector. Adjust the cable to a length at which the pan/tilt head will move smoothly.
• Set controller selection switch SW1 to the right side...

- 33 -
Connections
7When the camera and pan/tilt head are to be controlled by the AW-RP605A 
multi-function controller for transmitting composite or component signals
• Use the supplied camera cable to connect the unit with the convertible camera.
• Set controller selection switch SW1 to the left side (RP605), and select the transmission signal
selection setting that supports the analog/IEEE1394 card.
• Use a 10BASE-T straight cable (UTP category 5) to connect the unit’s CONTROL IN IP/RP
connector with...

- 34 -
Connections
8When the camera and pan/tilt head are to be controlled by the AW-RP605A 
multi-function controller for transmitting SDI signals
• Use the supplied camera cable to connect the unit with the convertible camera
containing the plugged-in SDI card (such as the AW-PB504N).
• Use a coaxial cable to connect the SDI card’s SDI OUT connector with the unit’s SDI
IN connector. Adjust the cable to a length at which the pan/tilt head will move
smoothly.
• Set controller selection switch SW1 to the...

- 35 -
Connections
9When the pan/tilt head is to be controlled by the AW-RP400 pan/tilt head control panel
for transmitting composite or component signals (and the AW-CB400 remote operation
panel is used to control the camera)
• Use the supplied camera cable to connect the unit with the convertible camera.
• Set controller selection switch SW1 to the right side (RP501), and select the transmission signal
selection setting that supports the analog/IEEE1394 card.
• Use a 10BASE-T straight cable (UTP...

- 36 -
Connections
:When the pan/tilt head is to be controlled by the AW-RP400 pan/tilt head control panel
for transmitting SDI signals (and the AW-CB400 remote operation panel is used to
control the camera)
• Use the supplied camera cable to connect the unit with the convertible camera
containing the plugged-in SDI card (such as the AW-PB504N).
• Use a coaxial cable to connect the SDI card’s SDI OUT connector with the unit’s SDI
IN connector. Adjust the cable to a length at which the pan/tilt head will...

- 37 -
Connections
;When the pan/tilt head is to be controlled by the AW-RP400 pan/tilt head control panel
for transmitting composite or component signals (and the WV-CB700A remote control
box is used to control the camera)
• Use the supplied camera cable to connect the unit with the convertible camera.
• Set controller selection switch SW1 to the right side (RP501), and select the transmission signal
selection setting that supports the analog/IEEE1394 card.
• Use a 10BASE-T straight cable (UTP category...

- 38 -
Connections

- 39 -
Connections
=When the camera and pan/tilt head are to be controlled by a personal computer or other
such unit
• Use the supplied camera cable to connect the unit with the convertible camera.
• Set controller selection switch SW1 to the right side (RP501), and select the
transmission signal selection setting that supports the analog/IEEE1394 card.
• Use the RS-232C cable (AW-CA28T9) to connect the personal computer or other such
unit with the unit’s CONTROL IN RS-232C connector.
• Use coaxial...

- 40 -
Connections
>When the camera and pan/tilt head are to be controlled by both the AW-RP501
controller and a personal computer
• Use the supplied camera cable to connect the unit with the convertible camera.
• Set controller selection switch SW1 to the right side (RP501), and select the transmission signal
selection setting that supports the analog/IEEE1394 card.
• Follow connection example 1to connect the unit and AW-RP501 controller. However, when
using a personal computer or other such unit to...