Panasonic Indoor Pan Tilt Head Aw Ph360n Operating Instructions

- 11 -
Installation (The installation work must be performed by your dealer without fail.)
$Transmission signal selection setting
The switches on the COMP and CONNECTOR printed circuit boards must be set to
correspond to the signals to be transmitted and components to be connected to the
pan/tilt head.
(When shipped, the analog settings are supported.)

OBefore setting the switches, make absolutely sure that the power of the AC adapter
which is to be connected to the pan/tilt head is set to...

- 12 -
$Setting the cable compensation circuit of video signals
(COMP switch of the COMP printed circuit board is set to “OFF” in the default setting.)
1When using the AW-RP501 controller or the AW-HB505 multiport hub (for
transmissions using composite signals)
When this controller (or multiport hub) has been connected to the pan/tilt head, it is
permissible for the connecting cables to be up to 1640 ft. (500 m) long when a
10BASE-T straight cable (UTP category 5) and coaxial cable (BELDEN 8281) are...

- 13 -
Installation (The installation work must be performed by your dealer without fail.)
Safety wire
$Installing the pan/tilt head
Be absolutely sure to follow the instructions below when installing the pan/tilt head. Failure
to do so may cause the pan/tilt head to slip out of position or fall.
OFor wall
Do not install the pan/tilt head on any of its sides.
The wall should be capable of supporting a weight of at least four times the pan/tilt head
with camera etc. weight 59.5 lb (27 kg).
OMake sure that...

- 14 -
Installation (The installation work must be performed by your dealer without fail.)
$Mounting the camera
The pan/tilt head’s camera mounting section has a mechanism for maintaining the
camera’s balance that moves the camera mounting plate using a guide roller as a fulcrum.
Use the described recommended lenses corresponding to the camera to be used.
(Before mounting a lens other than recommended lenses, consult with your dealer.)
1. Change the position of guide pin Aand/or the camera mounting...

- 15 -
Installation (The installation work must be performed by your dealer without fail.)

Adjust the balance by
moving the camera
mounting plate.
• Stand-alone installation
Adjust the balance by
moving the camera
mounting plate.

Camera Lens
AW-E350AW-LZ16MD55P
AW-LZ10MD6
AW-E650 AW-LZ16MD73P
AW-E655 AW-LZ16AF7G
AW-E750
AW-LZ17MD9AG
AW-E860

or
or
When the pan/tilt head is set at
suspended installation, change
the position of guide screws and
guide pin Bto adjust the balance
as well as the stand-alone...

- 16 -
Installation (The installation work must be performed by your dealer without fail.)
Chain
Chain
Chain attachment screw
M4!8 mm: with flat
washer/spring washer Chain attachment screw
M4!8 mm: with flat
washer/spring washer Chain attachment screw
M4!6 mm or M2.6!6 mm:
with flat washer/spring washer
Chain
With the AW-E655/AW-E750/AW-E860 With the AW-E350/AW-E650
Chain attachment screw
M4!8 mm: with flat
washer/spring washerChain attachment screw
M4!6 mm: with 
flat washer/spring 
washer
Mounting...

- 17 -
Installation (The installation work must be performed by your dealer without fail.)
OMounting a camera
When mounting a camera to the pan/tilt
head, take appropriate measures to
prevent the camera from falling or being
stolen.
1. Place the camera on the camera
mounting base and insert the guide pin
into the guide hole on the camera. 
2. Tighten the 2 camera mounting screws
to fix the camera firmly in place.
3. After mounting the camera, check that it
is firmly attached and that there is no
play....

- 18 -
Connections
$Connecting the connector panel(with the controller AW-RP501)
Zoom lens
Base connector front panelConvertible camera
AC adapter: AW-PS300A
MonitorCamera cable
(supplied)
DC cable
(UL Type SPT-2 2!16
AWG or UL Type NISPT-2
2!16 AWG, to be locally
purchased)10BASE-T (equivalent
to UTP category 5)
straight cable
Coaxial cable 
(BELDEN 8281) Coaxial cable
Base connector rear panel
AC adapter: AW-PS505A
Head connector panel
Control panel:
AW-RP501 

- 19 -
Connections
$Connecting the connector panel(with the controller AW-RP505)
Zoom lens
Base connector
front panel
AC adapter: AW-PS505A
AC adapter: AW-PS505AMultiport hub:
AW-HB505 Convertible camera
AC adapter: AW-PS300A
Preview
monitorMonitorCamera cable
(supplied)
10BASE-T
(equivalent to UTP
category 5)
straight cable 10BASE-T
(equivalent to UTP
category 5)
straight cable
Coaxial cable 
(BELDEN 8281)
Coaxial cable
(BELDEN 8281)
DC cable
(UL Type SPT-2 2!16
AWG or UL Type NISPT-2
2!16 AWG, to be...

- 20 -
Connections
Zoom lens
Base connector front panel
MonitorConvertible camera
Camera
cable
(supplied)
10BASE-T (equivalent to UTP
category 5) straight cable
Coaxial cable 
(BELDEN 8281)AC adapter: AW-PS300A
Multi-Function Controller: AW-RP605A
$Connecting the connector panel(with the controller AW-RP605A)
Coaxial
cableAC adapter: AW-PS505A
DC cable
(UL Type SPT-2 2!16
AWG or UL Type NISPT-2
2!16 AWG, to be locally
purchased)