Panasonic Home Network_system_ Users Guide

Accessing while away from home
If a mobile device is accessing the system while away from home (i.e., accessing from a different
network)
R The next mobile device that tries to access the system while away from home will be allowed to access
the system; the mobile device that was previously accessing the system will be disconnected.
R For mobile devices accessing at home, certain settings and features may be temporarily unavailable.
Camera features (while accessing at home)
If a mobile device is viewing...

RLandline calls can be received but not made.
R Other settings and features may be temporarily unavailable.
Exiting and logging out
Exiting the app
Use this procedure to exit the app.
iPhone, iPad
Use the standard iOS method for exiting an app.
Android devices
Use the standard Android method for exiting an app.
From the app’s home screen, you can also open the options menu ( “Displaying the options menu”,
Page 30) and then tap  [Exit].
Logging out while away from home
To log out of the system while away...

Status notifications for Android devices
The system provides information about system status by displaying status notifications, error messages,
and the following icons in your mobile device’s status bar and notifications panel.Window sensor was triggeredDoor sensor was triggeredMotion sensor was triggeredWater leak sensor was triggeredCamera motion sensor was triggeredCamera audio and video are being recordedIndoor camera sound sensor was triggeredIndoor camera temperature sensor was triggeredSmart plug...

Device was registered to the hubArm mode was changedEntry delay countdown in effectOutdoor camera is too cold
*1 You can disable these icons from being displayed in your mobile device’s status bar, if desired( “[Connection Status Icon] (Android devices only)”, Page 88).
Confirming status in the [Home Network] app home screen
The system can provide information about system status by displaying animations and messages in the
[Home Network]  app home screen. The icons shown below are animated in the...

Indicator blinking in two colors
Hub LED indicator
OffNo power, or LED indicator is turned off *1GreenNormal operation, connected to wireless router Registration mode Hub is searching for wireless routerGreen and yellowHub is starting upRedAlarm system is armed Alarm system was triggeredYellowInitial setup required Initial setup in progress, mobile device connected Initial setup is starting
*1 You can configure the hub so that its LED indicator does not light in most states. See  “General
settings”, Page...

GreenNo motion detectedRegistration mode (you pressed and held )RedMotion detectedSensor is out of range of the hub, or is not registered to a hub
Note:
R After pressing 
 and confirming the sensor’s status, press  again to turn off the LED
indicator and conserve battery power.
Window/door sensor LED indicator
The LED indicator on the window/door sensor does not light during normal operation. You can press
 and check the LED indicator to confirm the sensor’s status.
OffNo battery powerGreenWindow/door is...

Siren LED indicatorOffNo power, or LED indicator is turned off*1GreenNormal operationRegistration mode (you pressed and held )RedSensor is out of range of the hub, or is not registered to a hubAlarm system was triggered
*1 You can configure the siren so that its LED indicator does not light in most states. See  “Setting
device profiles (device names, locations, and other settings)”, Page 83.
Smart plug LED indicator
OffNo power, smart plug is off, or LED indicator is turned off *1GreenSmart plug is...

Sensors that can be used to trigger alarm system features
The following sensors can be used to trigger alarm system features.
– Window sensors and door sensors (KX-HNS101)
– Motion sensors (KX-HNS102)
– Water leak sensors (KX-HNS103)
– Built-in motion sensors in outdoor cameras (KX-HNC600)
– Built-in motion sensors in indoor cameras (KX-HNC200, KX-HNC210)
Note:
R The following sensors cannot be used to trigger alarm system features.
– Built-in sound and temperature sensors in indoor cameras (KX-HNC200,...

Canceling an alert
When the alarm system is triggered, you can confirm the triggered event in the  [Home Network] app
home screen or by using your mobile device’s notification features.
If the sensor alert screen is displayed, tap  [Stop] to cancel the alert. If the  [Dismiss] icon is displayed
while viewing live images from a camera, tap  [Dismiss] to cancel the alert.
Arming and disarming the alarm system
The alarm system features three modes. You can use the icons displayed at the top of the  [Home...

–[Arm Settings (Away)] : The settings you change will be applied when the arm mode is set to
[Arm: Away] .
– [Alert by Phone Call] : See  “Alert by phone call”, Page 41.
– [Change Arm PIN] : See  “Alarm system PIN”, Page 42.
4 Select the desired setting.
5 Change the settings as desired.
R Each setting is explained in this section.
6 Follow the on-screen instructions.
Enabling and disabling individual sensors
While configuring the settings for an arm mode, tap the name of the desired sensor and then...