Panasonic Home Network_system_ Users Guide

Before you begin
In this procedure, the hub will enter “temporary access point mode”. In this mode, you can connect your
mobile device directly to the hub using Wi-Fi®, and then use your mobile device to change the hub’s
Wi-Fi settings so that the hub can connect to your wireless router.
Confirm the following before you begin.
– Make sure you have installed the  [Home Network] app on your mobile device
– Make sure your wireless router and the hub are turned on and the hub’s LED indicator is lit in...

8When prompted, set the password used to log in to the hub while away from home and then tap  [OK].
9 When prompted, enter a name for your mobile device and then tap  [OK].
R This setting allows you to change the name assigned to your device. It can help you identify your
mobile device when performing certain operations, such as deregistering or making intercom calls
using a cordless handset.
10 When prompted, select whether you want to customize device profiles, i.e., the device name,
location, and...

8When prompted, select whether you want to customize device profiles, i.e., the device name,
location, and other settings for your devices.
R If you choose not to customize the device profiles now, you can change them later if desired (see
“Setting device profiles (device names, locations, and other settings)”, Page 83).
R If you choose to customize the device profiles now, change each setting as desired. When
finished, press your device’s “back” button repeatedly until the “completed” message is...

This section describes commonly used system features, the devices required for each example, and
briefly explains the required settings.
While away from home, you can receive a notification on your mobile device if the alarm system is
triggered.
Required devices
R Mobile device (smartphone or tablet) with an Internet connection
R Wireless router
R Hub (KX-HNB600)
R Any device equipped with a sensor that can trigger the alarm system
– Indoor Camera (KX-HNC200, KX-HNC210)
– Outdoor Camera (KX-HNC600)
–...

– Outdoor Camera (KX-HNC600)
Required procedures
R Hub initial setup and mobile device registration
Refer to the System Setup Guide included with your hub.
R Camera registration (if you didn’t purchase the camera as part of a pre-configured bundle)
Refer to the Installation Guide included with your camera.
R Use the  [Home Network]  app to configure a smart control scenario. Select a sensor as the trigger and
your camera as the target device.
See  “Creating a scenario that uses a sensor as the trigger”,...

RHub (KX-HNB600)
R Indoor Camera (KX-HNC200, KX-HNC210)
Required procedures
R Hub initial setup and mobile device registration
Refer to the System Setup Guide included with your hub.
R Camera registration (if you didn’t purchase the camera as part of a pre-configured bundle)
Refer to the Installation Guide included with your camera.
R Use the  [Home Network]  app to configure the camera’s sound alert feature.
See  “Sound alert (indoor cameras only)”, Page 55.
While at home, you can use your mobile device...

App basics (overview)
To begin, simply start the  [Home Network] app on your mobile device by tapping its icon (shown below).
To prevent unauthorized access to the system, you may need to enter a system password. Whether or
not you need to enter the system password depends on how your mobile device is accessing the system,
as explained below.
Accessing while at home
If your mobile device is connected to the same wireless network as the hub, you do not need to enter the
system password when accessing the...

your mobile device. You can change this setting later if desired in the privacy section your mobile
device’s  [Settings]  app.
Using the home screen
The  [Home Network]  app home screen is displayed when you start the app.
Connection mode
The message displayed at the top of the app’s home screen indicates the current connection mode.
– [Home Wi-Fi Connected]  is displayed when your mobile device is connected to the hub while at
home (i.e., your mobile device is connected to the same wireless router as...

  
[Arm: At Home] mode selected
  
[Arm: Away] mode selected
  
[Disarm] mode selected
  
Mobile device is not connected to hub; arm mode is unknown
Note:
R If another user changes the arm mode, the arm mode icons displayed at the top of the home screen of
your mobile device will not change immediately. The icons will be updated and display the current arm
mode the next time the app refreshes the home screen, such as when you start the app or return to
the home screen from another screen.
Feature icons...

Displays the system configuration screen.
Returning to the previous screen
iPhone, iPad
Tap 
.
Android devices
Press your device’s “back” button.
Returning to the [Home Network] app home screen
Press your mobile device’s home button and then start the  [Home Network] app again.
You can also use the shortcuts menu to return to the app’s home screen ( “Using the shortcuts menu”,
Page 30).
Displaying the options menu
The method used to display the options menu varies depending on your mobile device. Note...