Panasonic Home Network System Hd Camera Kx Hnc800 Installation Guide

							Initial setup (for Android device
us
e
rs)
R Do not perform this procedure
i f

 you want to integrate the
camera with your Home
Network System. Use the
procedure on page 24.
R If your mobile device is
already registered to a hub
and you want to use your
camera by itself, see
“Information for current hub
users”, page 22. 1
P
lug in the camera and wait
a b

out 1 minute for the
camera’s LED to light in green.
R If the LED does not light in
green, or if you experience
trouble during this
procedure, reset the
camera (page 25) and
then repeat this procedure.
2 Start the  [Home Network]
app.
R If prompted, follow the
on-screen instructions and
select the appropriate
region/country.
3 Tap  [HD Camera] .
4 Tap  [Set up the HD Camera] . 5
When prompted, press the
M S E

TUPN button on the back
of the camera.
R The LED indicator blinks in
green.
R The app temporarily
changes your mobile
device’s Wi-Fi setting so
that it connects to the
camera directly.
6 If necessary, enter the
password required to connect
to your wireless router and
then tap  [Next].
R The camera and your
mobile device connect to
your wireless router.
R If you enter the wrong
password, an error is
displayed. Repeat the initial
setup procedure from the
beginning.
7 When prompted, press the
MSETUP N button on the back
of the camera.
R The camera registers your
mobile device.
8 When prompted, set the
password that will be used to
access the camera.
9 When prompted, enter a
name for your mobile device
and then tap  [OK].
R This setting allows you to
change the name assigned
For a ssistance, please visit http://shop.panasonic.com/support
21 Setup
HNC800_(en_en)_0902_ver.220.pdf   212016/09/05   17:54:31 
						

							to your device. It can help
you
 identify your mobile
device when performing
certain operations, such as
deregistering a mobile
device.
R A list of all cameras
registered to the app is
displayed when initial setup
is complete. Information for current hub
u
se

rs
If your mobile device is already
registered to a hub and you want
to use your camera by itself (i.e.,
you do not want to integrate the
camera with your Panasonic
Home Network System), perform
the following.
1 Plug in the camera and wait
about 1 minute for the
camera’s LED to light in green.
RIf the LED does not light in
green, or if you experience
trouble during this
procedure, reset the
camera (page 25) and
then repeat this procedure.
2 Start the  [Home Network]
app.
3 From the  [Home Network]
app home screen, tap
[Settings] . 4
Tap  [Device Registration]  ®
[
 Registration]  ®  [HD
Camera]  ®  [Method 2] .
5 iPhone, iPad users
Continue from step 4 of the
initial setup procedure on
page 19.
Android device users
Continue from step 4 of the
initial setup procedure on
page 21.
22 For assistance, please visit http://shop.panasonic.com/support Setup
HNC800_(en_en)_0902_ver.220.pdf   222016/09/05   17:54:31 
						

							Registering
ad
d
itional mobile
devices to the
camera
Do not perform this procedure if
th e

 camera is integrated with
your Home Network System.
Use the procedure found in the
System Setup Guide included
with your hub and register the
additional mobile device to your
hub. After you set up the camera, you
ca
n

 register additional mobile
devices. You can register up to 8
mobile devices to a camera. Each
mobile device can be registered to
up to 32 cameras.
Confirm the following before you
begin.
– Make sure you have completed the initial setup procedure
– Make sure your mobile device can connect to the Internet
– Make sure your wireless router and the camera are turned on
– Make sure your mobile device and the camera are connected
to the same wireless router
1 Using the mobile device that
you want to register,
download the  [Home Network]
 app and then start
t h

e app.
R If prompted, follow the
on-screen instructions and
select the appropriate
region/country.
2 Tap  [HD Camera] .
3 Tap  [Add This Mobile
Device] .
4 When prompted, press the
MSETUP N button on the back
of the camera.
R The camera registers your
mobile device.
5 When prompted, enter the
password required to access
the camera.
RThis password was set
during initial setup.
6 When prompted, enter a
name for your mobile device
and then tap  [OK].
R This setting allows you to
change the name assigned
to your device. It can help
you identify your mobile
device when performing
certain operations, such as
deregistering a mobile
device.
R A list of all cameras
registered to the app is
displayed when registration
is complete.
For a ssistance, please visit http://shop.panasonic.com/support
23 Setup
HNC800_(en_en)_0902_ver.220.pdf   232016/09/05   17:54:31 
						

							Registering the
ca
m
era to your hub
Do not perform this procedure if
yo u

 are using the camera by
itself (i.e., you do not have a
KX-HNB600 hub). Use the initial
setup procedure (page 19). If you want to integrate your HD
ca
m

era with a Panasonic Home
Network System, you must
register the camera to the hub. Registering the camera
Co
n

firm the following before you
begin.
– Make sure you can use your mobile device to access the hub
– Make sure the hub’s firmware is up to date and that you are
using the latest version of the
[Home Network]  app.
For more information, refer to
the System Setup Guide
included with your hub and the
User’s Guide (page 31).
1 Plug in the camera and wait
about 1 minute for the
camera’s LED to light in green.
RIf the LED does not light in
green, or if you experience
trouble during this
procedure, reset the camera (page 25) and
th
e

n repeat this procedure.
2 Start the  [Home Network]
app.
3 From the  [Home Network]
app home screen, tap
[Settings] .
4 Tap  [Device Registration]  ®
[Registration]  ®  [HD
Camera]  ®  [Method 1] .
5 When prompted, press the
MSETUP N button on the back
of the camera.
R The camera registers your
mobile device.
R The app’s home screen is
displayed when registration
is complete.
6 Follow the on-screen
instructions. When prompted,
set the password that will be
used to access the camera.
Note:
R When registration is complete,
the hub sounds one long beep.
R If registration fails, the hub
sounds several short beeps.
24 For a
ssistance, please visit http://shop.panasonic.com/support Setup
HNC800_(en_en)_0902_ver.220.pdf   242016/09/05   17:54:31 
						

							Resetting the
ca
m
era
Use this procedure if you have
trouble setting up the camera.
1 Plug in the camera.
2 Using an object with a thin tip,
press and hold the reset
button on the back of the
camera for about 10 seconds,
then release the button when
the camera beeps. R
The camera’s settings are
re

set.
3 Wait for the camera’s LED to
light in green.
Note:
R After resetting the camera, you
cannot use the camera again
until it is set up. Refer to the
relevant page in this section to
set up the camera.
For assistance, please visit http://shop.panasonic.com/support 25 Setup
HNC800_(en_en)_0902_ver.220.pdf   252016/09/05   17:54:31  
						

							Information about
wi
r
eless
communication
The camera uses wireless
technology to communicate with
your wireless router. Refer to the
following information when
planning where to place the
camera.
R Do not use the camera in the
following areas or locations, as
they may cause malfunction or
interference to radio
communication.
– Indoor areas that have
certain types of radio or
mobile communications
equipment
– Locations near microwave ovens or Bluetooth devices
– Indoor areas where antitheft devices or 2.4 GHz
frequency devices such as
POS systems are used
R Do not place the camera in
areas where the following
materials or objects are located
between the camera and the
wireless router. These materials
and objects may interfere with
wireless communication or
cause wireless transmission
speed to become slower. – Metallic doors or shutters
– Wa

lls containing
aluminum-sheet insulation
– Walls made of concrete, stone, brick, or tin
– Multiple walls
– Steel shelving
– Fireproof glass
26 For assistance, please visit http://shop.panasonic.com/support Appendix
HNC800_(en_en)_0902_ver.220.pdf   262016/09/05   17:54:31 
						

							Information about
se
n
sor features
The camera has 3 sensor
features: a visual sensor used for
motion detection, a temperature
sensor, and a sound sensor.
Please read the following
information about each sensor
before deciding where to install
the camera.
Note:
R The camera’s sensor features
are not designed to be used in
situations that require high
reliability. We do not
recommend use of the sensor
features in these situations.
R Panasonic takes no
responsibility for any injury or
damage caused by the use of
the camera’s sensor features. Using visible light to
de
t

ect motion
The camera can detect motion by
recognizing changes in the brightness of areas that are visible
to 

the camera. Vertical detection range:
ap
p

rox. 67°
Note:
R Movement may be incorrectly
detected when the moving
object and the background have
similar colors.
R Movement may be incorrectly
detected when there are
sudden changes to the overall
brightness level, such as when
lights are turned on.
R Detection becomes difficult
when the image is dark.
R You can adjust the sensitivity of
the camera’s motion detection
feature, and select which areas
of the camera image are
monitored for motion detection.
For more information, refer to
the User’s Guide (page 31).
For assistance, please visit http://shop.panasonic.com/support 27Appendix
HNC800_(en_en)_0902_ver.220.pdf   272016/09/05   17:54:31A   
						

							Direction of motion
It
 
is easier to detect objects that
move sideways in front of the
camera, and more difficult to
detect objects that move directly
toward the front of the camera. It is difficult to detect
mo
v

ement directly towards
the front of the camera. It is easy to detect movement
si
d

eways in front of the
camera. Detection range
Horizontal detection range:
ap
p

rox. 121° Camera Temperature sensor
Th
e

 sensor is triggered when the
set temperature range is
exceeded.
Note:
R The temperature sensor may
not detect temperature
accurately if the camera is
exposed to warm or cool
breezes from heating/cooling
systems.
R You can adjust the temperature
setting of the temperature
sensor. For more information,
refer to the User’s Guide
(page 31). Sound sensor
Th
e

 sensor is triggered when the
set sound level is exceeded.
Note:
R The sound sensor may not
function as desired when the
camera is placed in noisy
environments.
R You can adjust the sound level
setting of the sound sensor. For
more information, refer to the
User’s Guide (page 31).
28 For assistance, please visit http://shop.panasonic.com/support Appendix
HNC800_(en_en)_0902_ver.220.pdf   282016/09/05   17:54:31AB
D
E
C       
						

							Information about
ni
g
ht vision mode
The camera features an array of
infrared LEDs that light
automatically in low-light
conditions, allowing camera
images to be viewable even when
the surrounding area is dark.
Note:
R When night vision mode is
active, the colors in camera
images may appear different
from normal.
R When night vision mode is
active, the array of infrared
LEDs that surround the
camera’s lens light up in a faint
red color that can be seen in
the dark.
R If the camera is installed in front
of a window and points directly
at the window, images may be
poor when night vision mode is
active. Wall mounting
Dr
i
ve two screws (not supplied)
into the wall, and then mount the
unit as shown. 31 mm (1 7/32 inches)
Screws
No t

e:
R Make sure that the wall and the
fixing method are strong
enough to support the weight of
the unit. Adjusting the angle
A
dj

ust the angle as desired.
Note:
R When adjusting the angle,
make sure the unit does not tip
over.
For assistance, please visit http://shop.panasonic.com/support 29Appendix
HNC800_(en_en)_0902_ver.220.pdf   292016/09/05   17:54:31AA B
B    
						

							Removing the
st
a
nd
1 Hold the camera upside down
and adjust the angle of the
stand as shown. 2
Insert a thin, non-metallic
ob

ject into the groove on the
bottom of the camera body,
and then remove the stand by
rotating its base as shown. Attaching the stand
In
s

ert a thin, non-metallic object
into the groove on the bottom of
the camera body, and then attach
the stand by rotating its base as
shown. 30
For assistance, please visit http://shop.panasonic.com/support Appendix
HNC800_(en_en)_0902_ver.220.pdf   302016/09/05   17:54:31