Panasonic Home Network System Hd Camera Kx Hnc800 Installation Guide

Initial setup (for Android device
us
e
rs)
R Do not perform this procedure
i f

 you want to integrate the
camera with your Home
Network System. Use the
procedure on page 24.
R If your mobile device is
already registered to a hub
and you want to use your
camera by itself, see
“Information for current hub
users”, page 22. 1
P
lug in the camera and wait
a b

out 1 minute for the
camera’s LED to light in green.
R If the LED does not light in
green, or if you experience
trouble during this
procedure, reset...

to your device. It can help
you
 identify your mobile
device when performing
certain operations, such as
deregistering a mobile
device.
R A list of all cameras
registered to the app is
displayed when initial setup
is complete. Information for current hub
u
se

rs
If your mobile device is already
registered to a hub and you want
to use your camera by itself (i.e.,
you do not want to integrate the
camera with your Panasonic
Home Network System), perform
the following.
1 Plug in the camera and wait
about 1...

Registering
ad
d
itional mobile
devices to the
camera
Do not perform this procedure if
th e

 camera is integrated with
your Home Network System.
Use the procedure found in the
System Setup Guide included
with your hub and register the
additional mobile device to your
hub. After you set up the camera, you
ca
n

 register additional mobile
devices. You can register up to 8
mobile devices to a camera. Each
mobile device can be registered to
up to 32 cameras.
Confirm the following before you
begin.
– Make...

Registering the
ca
m
era to your hub
Do not perform this procedure if
yo u

 are using the camera by
itself (i.e., you do not have a
KX-HNB600 hub). Use the initial
setup procedure (page 19). If you want to integrate your HD
ca
m

era with a Panasonic Home
Network System, you must
register the camera to the hub. Registering the camera
Co
n

firm the following before you
begin.
– Make sure you can use your mobile device to access the hub
– Make sure the hub’s firmware is up to date and that you are
using...

Resetting the
ca
m
era
Use this procedure if you have
trouble setting up the camera.
1 Plug in the camera.
2 Using an object with a thin tip,
press and hold the reset
button on the back of the
camera for about 10 seconds,
then release the button when
the camera beeps. R
The camera’s settings are
re

set.
3 Wait for the camera’s LED to
light in green.
Note:
R After resetting the camera, you
cannot use the camera again
until it is set up. Refer to the
relevant page in this section to
set up the camera.
For...

Information about
wi
r
eless
communication
The camera uses wireless
technology to communicate with
your wireless router. Refer to the
following information when
planning where to place the
camera.
R Do not use the camera in the
following areas or locations, as
they may cause malfunction or
interference to radio
communication.
– Indoor areas that have
certain types of radio or
mobile communications
equipment
– Locations near microwave ovens or Bluetooth devices
– Indoor areas where antitheft devices or...

Information about
se
n
sor features
The camera has 3 sensor
features: a visual sensor used for
motion detection, a temperature
sensor, and a sound sensor.
Please read the following
information about each sensor
before deciding where to install
the camera.
Note:
R The camera’s sensor features
are not designed to be used in
situations that require high
reliability. We do not
recommend use of the sensor
features in these situations.
R Panasonic takes no
responsibility for any injury or
damage caused by the...

Direction of motion
It
 
is easier to detect objects that
move sideways in front of the
camera, and more difficult to
detect objects that move directly
toward the front of the camera. It is difficult to detect
mo
v

ement directly towards
the front of the camera. It is easy to detect movement
si
d

eways in front of the
camera. Detection range
Horizontal detection range:
ap
p

rox. 121° Camera Temperature sensor
Th
e

 sensor is triggered when the
set temperature range is
exceeded.
Note:
R The...

Information about
ni
g
ht vision mode
The camera features an array of
infrared LEDs that light
automatically in low-light
conditions, allowing camera
images to be viewable even when
the surrounding area is dark.
Note:
R When night vision mode is
active, the colors in camera
images may appear different
from normal.
R When night vision mode is
active, the array of infrared
LEDs that surround the
camera’s lens light up in a faint
red color that can be seen in
the dark.
R If the camera is installed in front...

Removing the
st
a
nd
1 Hold the camera upside down
and adjust the angle of the
stand as shown. 2
Insert a thin, non-metallic
ob

ject into the groove on the
bottom of the camera body,
and then remove the stand by
rotating its base as shown. Attaching the stand
In
s

ert a thin, non-metallic object
into the groove on the bottom of
the camera body, and then attach
the stand by rotating its base as
shown. 30
For assistance, please visit http://shop.panasonic.com/support Appendix...