Panasonic Home Network System Hd Camera Kx Hnc800 Installation Guide

network conditions and wireless
sig
nal quality.
R This product may be used in
ways that violate the privacy or
publicity rights of others. You
are responsible for the ways in
which this product is used. For best
per

formance Product location/avoiding noise
Th
i

s product uses radio waves to
communicate with a wireless
router.
R For maximum coverage and
noise-free communications,
place this product:
– at a convenient, central
location with no obstructions
between this product and the
wireless router.
–...

R
The maximum communication
ra
nge may be shortened when
the product is used in the
following places: Near
obstacles such as hills, tunnels,
underground, near metal
objects such as wire fences, etc.
R Operating the product near
electrical appliances may cause
interference. Move away from
the electrical appliances. Other information
Routine care
R
Wi p

e the outer surface of the
product with a soft moist cloth.
R Do not use benzine, thinner, or
any abrasive powder. Camera image quality
R
Ca m

era images...

Notice
For assistance, please visit http://shop.panasonic.com/support
13Important InformationHNC800_(en_en)_0902_ver.220.pdf   132016/09/05   17:54:30  

Part names and functions
A
Brightness sensor
All
ows the camera to switch automatically
to night vision mode in low-light conditions.
B Lens
C Privacy shutter
Pr
e

vents others from monitoring live
camera images or sound when the shutter
is closed.
D Microphone
E LED indicator
F microSD card slot
G Stand
H MS ETUP
N
U s

ed when performing initial setup.
I Speaker
J micro-USB connector
Us
e

d to connect the AC adaptor to the
camera.
K Reset button
Use

d to reset the camera’s settings.
L Temperature...

LED indicator
Yo
u
 can use the LED indicator to confirm the camera’s status. Indicator Status
Off No power, or LED indicator is turned off *
1
B l

ue, lit Normal operation, connected to wireless
rou

ter*1
, privacy shutter is open
White, lit Normal operation, connected to wireless
rou

ter*1
, privacy shutter is closed
White, blinking quickly Camera is searching for wireless router
Green, lit Initial setup required
Green, blinking slowly Initial setup is in progress with mobile device con

nected...

Connections
1 Insert the AC adaptor plug
( A ) 
firmly into the camera’s
micro-USB connector.
2 Connect the AC adaptor ( B)
to the power outlet.
3 Insert a microSD card
(user-supplied;  C) into the
camera’s microSD card slot.
(This is not necessary if you do not want to record camera
images.) Note:
R
Use

 only the supplied AC adaptor S006AKU0500100.
R To remove the microSD card, push in the microSD card and then
remove it. Note about power connections
AC adaptor connection
R
Th e

 AC adaptor must...

Setup overview
Af
t
er you have connected your camera, here is what you will need to do
in order to access it from your mobile device. Each procedure is
explained in this chapter. Using the camera by itself
( n o

 integration with a Home
Network System) Integrating the camera with a
H
om
e Network System
(registering to a KX-HNB600 hub)
1 Download (page 18)
Do

wnload the  [Home
Network]  app to your mobile
device.
2 Set up the camera
(page 19) Use the  [Home Network]  app
to configure the camera to...

Downloading the
[H
o
me Network]
app
Download information is available
at the web page listed below.
www.panasonic.net/pcc/support/
tel/homenetwork/ Using your device’s app store
iP
h

one, iPad users
Search for “Panasonic Home
Network System”. iPad users
should search in the “iPhone only”
category.
Android™ device users
Search for “Panasonic Home
Network System”. Compatible mobile devices
iP
h

one 4 or later, iPad, or iPad
mini (iOS 6.0 or later) or an
Android device (Android 4.0 or
later)
Note:
R The...

Setting up the
ca
m
era (initial
setup)
Confirm the following before you
begin.
– Make sure you have installed the  [Home Network]  app on
your mobile device
– Make sure the camera is located within range of your
wireless router
– Make sure your mobile device is connected to your wireless
router
– Make sure your mobile device can connect to the Internet
– Make sure you know the network name (SSID) and
password assigned to your
wireless router Initial setup (for iPhone, iPad
us
e

rs)
R Do not perform...

of the camera, and then tap
[Ne
xt].
R The LED indicator blinks in
green.
6 Change your mobile device’s
Wi-Fi setting temporarily so
that it connects to the camera
directly.
ROpen your mobile device’s
[Settings]  app, tap [Wi-Fi],
select
“KX-HNC800_Panasonic”,
enter “00000000” as the
password, and then tap
[Join] .
R If more than 1 item named
“KX-HNC800_Panasonic” is
displayed, wait approx. 10
minutes and perform this
procedure from the
beginning.
7 Start the  [Home Network]
app again.
8 If necessary,...