Panasonic Hdc Z10000 Owners Manual
Have a look at the manual Panasonic Hdc Z10000 Owners Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
141VQT3U98 ≥When using a chemical dust cloth, follow the instructions that came with the cloth. Do not use the unit for surveillance purposes or other business uses. ≥ This unit was designed for consumer intermittent use. It was not intended for continuous use, or for any industrial or commercial application resulting in prolonged use. ≥ In certain situations, continuous use could cause the unit to overheat and cause a malfunction. Such use is strongly discouraged. When you are not going to use the unit for an extended time ≥ When storing the unit in a cupboard or cabinet, it is recommended that you place a desiccant (silica gel) in with it. Do not lift up this unit by the handle with the tripod still attached ≥ When the tripod is attached, its weight will also affect the unit’s handle, possibly causing the handle to break and hurting the user. ≥ To carry the unit while the tripod is attached, take hold of the tripod. Do not swing the unit around, shake it by, or allow it hang from the handle ≥ Do not jar, swing, or shake the unit by its handle. Any strong jolt to the handle may damage the unit or result in personal injury. Do not allow the cord to drag on the ground or pull a connected cord along the passage ≥ The cord will be damaged, causing fire or electrical shock, when the cord gets caught by the feet, excite will also cause personal injury. The battery used in this unit is a rechargeable lithium-ion battery. It is susceptible to humidity and temperature and the effect increases the more the temperature rises or falls. In cold areas, the full charge indication may not appear or the low battery indication may appear about 5 minutes after starting use. At high temperatures, the protection function may be triggered, making it impossible to use the unit. Be sure to detach the battery after use. ≥ If the battery is left attached, a minute amount of current continues to flow even if the unit is off. Keeping the unit in this state may result in over discharge of the battery. This may result in you not being able to use the battery even after it is charged. ≥ The battery should be stored in the vinyl bag so metal does not come into contact with the terminals. ≥ The battery should be stored in a cool place free from humidity, with as constant temperature as possible. (Recommended temperature: 15 oC to 25 oC (59 °F to 77 °F), Recommended humidity: 40%RH to 60%RH) ≥ Extremely high temperatures or low temperatures will shorten the life of the battery. ≥ If the battery is kept in high-temperature, high-humidity, or oily-smoky places, the terminals may rust and cause malfunctions. ≥ To store the battery for a long period of time, we recommend you charge it once every year and store it again after you have completely used up the charged capacity. ≥ Dust and other matter attached to the battery terminals should be removed. Prepare spare batteries when going out for recording. ≥ Prepare batteries enough to last for 3 to 4 times the period you are planning to record for. Cold places such as a ski resort can shorten recording time. If you drop the battery accidentally, check to see if the terminals are damaged. About the battery HDC-Z10000P-VQT3U98_mst.book 141 ページ 2011年10月17日 月曜日 午後2時24分
142VQT3U98 ≥When this unit or battery charger is attached with the terminal part in a deformed state, this unit or battery charger may be damaged. Do not throw old battery into fire. ≥ Heating a battery or throwing it into a fire may result in an explosion. If the operating time is very short even after the battery has been recharged, the battery has worn out. Please purchase a new battery. ≥ If the temperature of the battery is extremely high or extremely low, charging may take time or the battery may not be charged. ≥ If the charging lamp keeps flashing, make sure that the terminals of the battery or the battery charger are not exposed to dirt, foreign objects or dust, then reconnect them properly. Disconnect the AC cable from the AC outlet when you remove dirt, foreign objects or dust on the terminals of the battery or the battery charger. If the charging lamp is still flashing, the temperature of the battery may be extremely high or extremely low or something may be wrong with the battery or battery charger. Contact your dealer. ≥ If you use the AC adaptor or battery charger near a radio, radio reception may be disturbed. Keep the AC adaptor or battery charger 1 m (3.3 feet) or more away from the radio. ≥ When using the AC adaptor or battery charger, it may generate whirring sounds. However, this is normal. ≥ After use, be sure to disconnect the AC cable from the AC outlet. (If you leave this unit connected, the AC adaptor will consume approximately 0.3 W and the battery charger approximately 0.3 W of current.) ≥ Always keep the electrodes of the AC adaptor, battery charger and battery clean.About the AC adaptor/battery charger HDC-Z10000P-VQT3U98_mst.book 142 ページ 2011年10月17日 月曜日 午後2時24分
143VQT3U98 About 3D recording After adjusting the convergence dial, check that you can view images in 3D. ≥It may not be possible to correctly record 3D image in following cases: jWhen operating the zoom after adjustment or changing the subject j When recording with the convergence point in an extreme forward or rearward position ≥ Use the 3D guide display as guidance. (l 41) Do not record a subject at less than the minimum focus distance. ≥ The 3D effects may be more pronounced, and therefore cause tiredness or discomfort. ≥ The minimum recording distance for this unit changes depending on the zoom and convergence point settings. Use the 3D guide display as guidance. ( l41) When recording, be careful not to shake the unit. ≥ Tiredness or discomfort may result if the shake is pronounced, due to riding in a vehicle or walking etc. ≥ When moving the unit as you record, move it slowly. ≥ We recommend using a tripod. About 3D viewing Anyone who is hyper sensitive to light, suffers from heart disease or is otherwise unwell should avoid viewing 3D video. ≥Doing may have an adverse affect on such medical conditions. If you feel tired, uncomfortable or otherwise strange when viewing 3D video, stop viewing at once. ≥ Continuing to view may cause illness. ≥ Please rest appropriately after stopping the viewing. When viewing 3D video, we recommend taking a break every 30 to 60 minutes. ≥ Viewing for extended periods may cause eye-fatigue. Short-sighted or far-sighted persons, those with differences in the sight of their right and left eyes, and those with astigmatism are advised to correct their vision by wearing glasses etc. Stop viewing if you can clearly see a double image while viewing 3D video. ≥ There are differences in the way that different people experience 3D video images. Please correct your sight appropriately before viewing 3D video. ≥ You can change the 3D setting of your television or 3D output setting of the unit to 2D. About 3D HDC-Z10000P-VQT3U98_mst.book 143 ページ 2011年10月17日 月曜日 午後2時24分
144VQT3U98 When disposing of or giving away the SD card, note that: ≥Formatting and deletion of this unit or computer only changes the file management information and does not completely delete the data in the SD card. ≥ It is recommended that the main SD card is either physically destroyed or the SD card is physically formatted using this unit when disposing of or giving away the SD card. ≥ To physically format, connect this unit to the AC adaptor, select [OTHER FUNCTION] # [FORMAT CARD] # [SD CARD 1] or [SD CARD 2] from the menu, and touch [YES]. Press and hold recording start/stop button in the following screen for three seconds. Screen to delete the SD card data is displayed, so select [YES] and follow the instruction on the screen. ≥ The customer is responsible for the management of the data in the SD card. ≥ When the LCD monitor gets dirty, wipe it with a soft cloth, such as eye glass cleaner. ≥ Do not touch the LCD monitor with your finger nails, or rub or press with strong force. ≥ It may become hard to see or hard to recognize the touch when the LCD protection sheet is affixed. ≥ In a place with drastic temperature changes, condensation may form on the LCD monitor. Wipe it with a soft cloth, such as eye glass cleaner. ≥ When the unit has become very cold, for example due to storage in a cold area, its LCD monitor will be slightly darker than usual immediately after the unit is turned on. The normal brightness will be restored when the unit’s internal temperature rises. About the SD cardLCD monitor/viewfinder Extremely high precision technology is employed to produce the LCD Monitor screen featuring a total of approximately 1,152,000 dots. The result is more than 99.99% effective dots with a mere 0.01% of the dots inactive or always lit. However, this is not a malfunction and does not affect the recorded picture. Extremely high precision technology is employed to produce the viewfinder screen featuring a total of approximately 1,226,000 dots. The result is more than 99.99% effective dots with a mere 0.01% of the dots inactive or always lit. However, this is not a malfunction and does not affect the recorded picture. HDC-Z10000P-VQT3U98_mst.book 144 ページ 2011年10月17日 月曜日 午後2時24分
145VQT3U98 When condensation forms on the unit, the lens will cloud up and the unit may not work properly. Make every effort to ensure that condensation does not form. If it does form, take the actions described below. Causes of condensationCondensation takes place when the ambient temperature or humidity is changed as follows. ≥When this unit is brought inside from the cold (e.g. a ski slope) to a warm room. ≥ When this unit is moved from an air-conditioned car to outside. ≥ When a cold room has been warmed up quickly. ≥ When cool wind from an air conditioner is directly blown onto this unit. ≥ After rain showers. ≥ When this unit is in a very humid place where the air is thick with steam. (e.g. a heated swimming pool) Helpful hint If, for example, you have used this unit for recording on a ski slope and are taking it into a heated room, place the unit inside a plastic bag, remove as much of the air from inside the bag as possible, then seal the bag. Leave the unit for about an hour in the room so the temperature of the unit is close to the ambient temperature of the room, then use it. About condensation HDC-Z10000P-VQT3U98_mst.book 145 ページ 2011年10月17日 月曜日 午後2時24分
146VQT3U98 ∫Carefully observe copyright laws Whatever you have recorded and created can be used for your personal entertainment only. Under copyright laws, other materials cannot be used without obtaining permission from the holders of the copyrights. ∫Licenses ≥SDXC Logo is a trademark of SD-3C, LLC. ≥ “AVCHD”, “AVCHD 3D”, “AVCHD Progressive”, “AVCHD 3D/Progressive” and the “AVCHD 3D/Progressive” logo are trademarks of Panasonic Corporation and Sony Corporation. ≥ Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. ≥ HDMI, the HDMI Logo, and High- Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. ≥ x.v.Color ™ is a trademark. ≥ Microsoft®, Windows® and Windows Vista® are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. ≥ Microsoft product screen shot(s) reprinted with permission from Microsoft Corporation. ≥ IBM and PC/AT are registered trademarks of International Business Machines Corporation of the U.S. ≥ Intel ®, Pentium®, Celeron® and Intel®Core™ are trademarks of Intel Corporation in the U.S. and/or other countries. ≥ Mac and Mac OS are trademarks of Apple Inc. registered in the U.S. and other countries. ≥ Other names of systems and products mentioned in these instructions are usually the registered trademarks or trademarks of the manufacturers who developed the system or product concerned. This product is licensed under the AVC patent portfolio license for the personal and non-commercial use of a consumer to (i) encode video in compliance with the AVC Standard (“AVC Video”) and/or (ii) decode AVC Video that was encoded by a consumer engaged in a personal and non-commercial activity and/or was obtained from a video provider licensed to provide AVC Video. No license is granted or shall be implied for any other use. Additional information may be obtained from MPEG LA, LLC. See http://www.mpegla.com . Others About copyright HDC-Z10000P-VQT3U98_mst.book 146 ページ 2011年10月17日 月曜日 午後2時24分
147VQT3U98 ≥SD cards are only mentioned with their main memory size. The stated times are the approximate recordable times for continuous recording. ≥ If recording for long periods, prepare batteries for 3 or 4 times the period you wish to record for. ( l20) ≥ The default setting is [1080/60i] (3D Recording Mode)/[HA] (2D Recording Mode). ≥ Maximum continuously recordable time for one scene: 6 hours ≥ The recording is paused once when the recording time for one scene exceeds 6 hours, and the recording will automatically resume after a few seconds. ≥ The recordable time may be reduced if recording with a lot of action is recorded or recording of short scene is repeated. Others Recording modes/approximate recordable time 3D/2D Recording Mode3D Recording Mode Recording format[1080/60i][1080/30p][1080/24p] Recording methodAVCHD 3D Picture size1920k1080/60i1920k1080/60i1920k1080/24p SD card 4GB 18 min 16 GB 1h15min 64 GB 5h15min 3D/2D Recording Mode2D Recording Mode Recording format (Interlace)[PH][HA][HE] Recording methodAV C H D Picture size1920k1080/60i1920k1080/60i1920k1080/60i SD card 4GB 21min 30min 1h30min 16 GB 1h30min 2h 6h40min 64 GB 6h 8h30min 27h30min 3D/2D Recording Mode2D Recording Mode Recording format (Progressive)[1080/60p][1080/30p][1080/24p] Recording methodAVCHD ProgressiveAVCHD Picture size1920k1080/60p1920k1080/60i1920k1080/24p SD card 4GB 18 min 21 min 16 GB 1h15min 1h30min 64 GB 5h15min 6h HDC-Z10000P-VQT3U98_mst.book 147 ページ 2011年10月17日 月曜日 午後2時24分
148VQT3U98 ≥SD cards are only mentioned with their main memory size. The stated number is the approximate number of recordable pictures. When [3D/2D REC MODE] is set to [3D] When [3D/2D REC MODE] is set to [2D] ≥ Number of recordable pictures when set to [3D] will be less than when set to [2D] since it will record both 3D still pictures and 2D still pictures simultaneously. ≥ Number of recordable pictures that can be displayed is 9999. If the number of recordable pictures exceeds 9999, R 9999+ is displayed. The number will not change when the picture is taken until the number of recordable pictures gets less than 9999. ≥ The memory capacity indicated on the label of an SD card is the total of the capacity for copyright protection and management and the capacity which can be used on the unit, a PC etc. Others Approximate number of recordable pictures Picture size 1920k 1080 Recording format of the still pictureMPO and JPEG SD card 4GB 1000 16 GB 4400 64 GB 18000 Picture size 2304k 1296 Recording format of the still pictureJPEG SD card 4GB 2400 16 GB 10000 64 GB 40000 2.1M M3 HDC-Z10000P-VQT3U98_mst.book 148 ページ 2011年10月17日 月曜日 午後2時24分
149VQT3U98 High Definition Video Camera Information for your safety Others Specifications Power source:DC 12 V (When using AC adaptor) DC 7.2 V (When using battery) Power consumption: 16.7 W Recording format: AVCHD format version 2.0 compliant (AVCHD 3D/Progressive) Motion picture compression: 3D Recording Mode; MPEG-4 MVC/H.264 2D Recording Mode; MPEG-4 AVC/H.264 Audio compression: Dolby Digital (5.1 ch/2 ch), Linear PCM (2 ch) Recording mode and transfer rate: 3D Recording Mode [1080/60i], [1080/30p], [1080/24p]; Maximum 28 Mbps (VBR) 2D Recording Mode [1080/60p]; Maximum 28 Mbps (VBR) [PH], [1080/30p], [1080/24p]; Maximum 24 Mbps (VBR) [HA]; Average 17 Mbps (VBR) [HE]; Average 5 Mbps (VBR) Refer to page 147 for the recordable time and picture size. Still picture recording format: 3D still pictures; MPO corresponding 2D still pictures; JPEG corresponding (Desi gn rule for Camera File system, based on Exif 2.2 standard) Refer to page 148 for the picture size and number of recordable pictures. Recording media: SD Memory Card (FAT12 and FAT16 system compliant) SDHC Memory Card (FAT32 system compliant) SDXC Memory Card (exFAT system compliant) Refer to page 22 for details on SD cards usable in this unit. HDC-Z10000P-VQT3U98_mst.book 149 ページ 2011年10月17日 月曜日 午後2時24分
150VQT3U98 Image sensor: 1/4.1z 3MOS image sensor k2 Total; 9150 K (3050 K k3) k2 Effective pixels; 3D Recording Mode Motion picture/Still picture; 6210 K (2070 K k3) (16:9) k2 2D Recording Mode Motion picture/Still picture; 6570 K (2190 K k3) (16:9) Lens: Auto Iris optical zoom (Full range AF) F value (focal length) 3D Recording Mode; F1.5 to F2.7 (Focal length; 2.84 mm to 28.4 mm) 2D Recording Mode; F1.5 to F2.8 (Focal length; 2.84 mm to 34.1 mm) 35 mm equivalent; 3D Recording Mode Motion picture/Still picture; 32 mm to 320 mm (16:9) 2D Recording Mode Motion picture/Still picture; 29.8 mm to 368.8 mm (16:9)Minimum focus distance;3D Recording Mode Approx. 30 cm (0.98 feet) (Wide)/Approx. 1.2 m (3.9 feet) (Tele) 2D Recording Mode Approx. 3.5 cm (1.4 q) (Wide)/Approx. 1.2 m (3.9 feet) (Tele) Zoom: 3D Recording Mode; 10 k optical zoom 2D Recording Mode; 12 k optical zoom, 23 k i.Zoom, 2 k/5k/10 k digital zoom Image stabilizer function: 3D Recording Mode; Optical (Power O.I.S.) 2D Recording Mode; Optical (Hybrid Optical Image Stabilizer, Active Mode) Convergence point adjustment: Approx. 45 cm (1.5 feet) to Approx. 40 m (131.2 feet) Monitor: 3.5 z wide LCD monitor (Approx. 1152 K dots) Viewfinder: 0.45 z wide EVF (Approx. 1226 K dots) Microphone: 5.1 channel surround microphone (with a zoom microphone/focus microphone function)/ stereo microphone Speaker: 1 round speaker, dynamic type White balance adjustment: Auto tracking white balance system Standard illumination: 1,400 lx Minimum required illumination: Approx. 5 lx (1/30 with [AUTO SLOW SHTR] is set to [ON]) HDC-Z10000P-VQT3U98_mst.book 150 ページ 2011年10月17日 月曜日 午後2時24分