Panasonic Hdc Sd800 Owners Manual

							141VQT3K35
∫If scenes do not change smoothly when played back on another 
device (AVCHD, 1080/60p)
The images may be still for several seconds at  the joins between the scenes if the following 
operations are performed when multiple scenes have been continuously played back using 
another unit.
≥ Just how smoothly the scenes will be play ed back depends on the playback unit. 
Depending on the unit used, the images may stop moving and become still for a moment 
even when none of the following conditions are applicable.
≥ A continuous recording of motion picture data that exceeds 4 GB may momentarily stop at 
every 4 GB of data when played back with another device.
≥ It may not play back smoothly when the editing of scenes was done with the HD Writer AE 
3.0, but it will play back smoothly if you set the seamless settings in the HD Writer AE 3.0. 
Refer to the operating instructions for the HD Writer AE 3.0.
Principal reasons for not playing back smoothly
≥ When the scenes were recorded on different dates
≥ When scenes lasting under 3 seconds have been recorded
≥ When PRE-REC was used for recording
≥ When the Interval recording is used
≥ When deleting scenes
≥ When selected scenes are copied to a disc in a connected DVD burner
≥ When scenes recorded with more than 99 scenes on the same date
HDCSD800P-VQT3K35_mst.book  141 ページ  ２０１０年１２月２０日　月曜日　午前９時４分 
						

							142VQT3K35
Keep this unit as far away as possible 
from electromagnetic equipment (such 
as microwave ovens, TVs, video games 
etc.).
≥If you use this unit on top of or near a TV, 
the pictures and/or sound on this unit may 
be disrupted by electromagnetic wave 
radiation.
≥ Do not use this unit near cell phones 
because doing so may result in noise 
adversely affecting the pictures and/or 
sound.
≥ Recorded data may be damaged, or 
pictures may be distorted, by strong 
magnetic fields created by speakers or 
large motors.
≥ Electromagnetic wave radiation generated 
by microprocessors may adversely affect 
this unit, disturbing the pictures and/or 
sound.
≥ If this unit is adversely affected by 
electromagnetic equipment and stops 
functioning properly, turn this unit off and 
remove the battery or disconnect AC 
adaptor. Then reinsert the battery or 
reconnect AC adaptor and turn this unit 
on.
Do not use this unit near radio 
transmitters or high-voltage lines.
≥ If you record near radio transmitters or 
high-voltage lines, the recorded pictures 
and/or sound may be adversely affected.
Make sure to use the supplied cords and 
cables. If you use optional accessories, 
use the cords and the cables supplied 
with them.
Do not extend the cords and the cables. Do not spray insecticides or volatile 
chemicals onto the unit.
≥
If the unit is sprayed with such chemicals, 
its body may be marred and the surface 
finish may peel off.
≥ Do not leave rubber or plastic products in 
contact with the unit for a long time.
When you use the unit in a sandy or 
dusty place such as a beach, do not let 
sand or fine dust get into the body and 
terminals of the unit.
Also, keep the unit away from sea water.
≥ Sand or dust may damage the unit. (Care 
should be taken when inserting and 
removing a card.)
≥ If sea water splashes onto the unit, wipe 
off the water with a well wrung cloth. Then 
wipe the unit again with a dry cloth.
When carrying the unit, do not drop or 
bump it.
≥ A strong impact can break the unit’s 
casing, causing it to malfunction.
Cleaning
≥ Before cleaning, detach the battery or pull 
the AC cable from the AC outlet, and then 
wipe the unit with a soft, dry cloth.
≥ If the unit is very dirty, dip a cloth in water 
and squeeze firmly, and then wipe the unit 
with the damp cloth. Next, dry the unit with 
a dry cloth.
≥ Use of benzine, paint thinner, alcohol, or 
dishwashing liquid may alter the camera 
body or peel the surface finish. Do not use 
these solvents.
≥ When using a chemical dust cloth, follow 
the instructions that came with the cloth.
Others
Cautions for use
About this unit
The unit and the SD card become warm 
during use. This is not a malfunction.
HDCSD800P-VQT3K35_mst.book  142 ページ  ２０１０年１２月２０日　月曜日　午前９時４分 
						

							143VQT3K35
Do not use the unit for surveillance 
purposes or other business uses.
≥This unit was designed for consumer 
intermittent use. It was not intended for 
continuous use, or for any industrial or 
commercial application resulting in 
prolonged use.
≥ In certain situations, continuous use could 
cause the unit to overheat and cause a 
malfunction. Such use is strongly 
discouraged.
When you are not going to use the unit 
for an extended time
≥ When storing the unit in a cupboard or 
cabinet, it is recommended that you place 
a desiccant (silica gel) in with it.
The battery used in this unit is a 
rechargeable lithium-ion battery. It is 
susceptible to humidity and temperature and 
the effect increases the more the 
temperature rises or falls. In cold areas, the 
full charge indication may not appear or the 
low battery indication may appear about 
5 minutes after starting use. At high 
temperatures, the protection function may 
be triggered, making it impossible to use the 
unit.
Be sure to detach the battery after use.
≥ If the battery is left attached, a minute 
amount of current continues to flow even if 
the unit is off. Keeping the unit in this state 
may result in over discharge of the battery. 
This may result in yo u not being able to 
use the battery even after it is charged.
≥ The battery should be stored in the vinyl 
bag so metal does not come into contact 
with the terminals.
≥ The battery should be stored in a cool 
place free from humidity, with as constant 
temperature as possible. (Recommended 
temperature: 15 °C to 25 °C (59 °F to 
77 °F), Recommended humidity: 40%RH 
to 60%RH) ≥
Extremely high temperatures or low 
temperatures will shorten the life of the 
battery.
≥ If the battery is kept in high-temperature, 
high-humidity, or oily-smoky places, the 
terminals may rust and cause 
malfunctions.
≥ To store the battery for a long period of 
time, we recommend you charge it once 
every year and store it again after you 
have completely used up the charged 
capacity.
≥ Dust and other matter attached to the 
battery terminals should be removed.
Prepare spare batteries when going out 
for recording.
≥ Prepare batteries enough to last for 3 to 4 
times the period you are planning to 
record for. Cold places such as a ski resort 
can shorten recording time.
If you drop the battery accidentally, 
check to see if the terminals are 
damaged.
≥ Attaching a battery with damaged 
terminals can damage the unit.
Do not throw an old battery into fire.
≥ Heating a battery or throwing it into a fire 
may result in an explosion.
If the operating time is very short even 
after the battery has been recharged, the 
battery has worn out. Please purchase a 
new battery.
About the battery
HDCSD800P-VQT3K35_mst.book  143 ページ  ２０１０年１２月２０日　月曜日　午前９時４分 
						

							144VQT3K35
≥If the temperature of the battery is 
extremely high or extremely low, charging 
may take time or the battery may not be 
charged.
≥ If you use the AC adaptor near a radio, 
radio reception may be disturbed. Keep 
the AC adaptor 1 m (3.3 feet) or more 
away from the radio.
≥ When using the AC adaptor, it may 
generate whirring sounds. However, this is 
normal.
≥ After use, be sure to disconnect the AC 
adaptor. (If it is left connected, a minute 
amount of current is consumed.)
≥ Always keep the electrodes of the AC 
adaptor and battery clean. When the status indicator is flashing at a 
particularly fast or slow rate, the 
following should be considered.
Flashing with approx. 4 second period 
(off for approx. 2 seconds, on for approx. 
2 seconds):
≥
When the battery is over discharged or the 
temperature of the battery is too high or 
low. It can be charged, but it may take a 
few hours to complete the charging 
normally.
≥ It will flash in 2 second intervals when 
normal charging resumes. Even in such 
cases, it may start flashing in 4 second 
intervals until charging is completed 
depending on the conditions of use.
Flashing with approx. 0.5 second period 
(off for approx. 0.25 second, on for 
approx. 0.25 second):
≥ The battery is not charged. Remove the 
battery from the unit, and try charging 
again.
≥ Check that the terminals of the unit or 
battery are not dirty or covered with a 
foreign object, and connect the battery 
correctly once again. If a foreign object or 
dirt is present, turn off the unit before 
removing.
≥ The battery or environment is at an 
extremely high or low temperature. Wait 
until the temperature has returned to an 
appropriate level and try charging again. If 
you are still unable to charge, there may 
be a fault in the unit, battery or AC 
adaptor.
Off:
≥ Charging has finished.
≥ If the status indicator stays off despite the 
charging being unfinished, there may be a 
fault in the unit, battery or AC adaptor. 
Refer to page 143 for details on the 
battery.
About the AC adaptorAbout status indicator during 
charging
HDCSD800P-VQT3K35_mst.book  144 ページ  ２０１０年１２月２０日　月曜日　午前９時４分 
						

							145VQT3K35
About 3D recording
Attach the 3D Conversion Lens securely. 
It must not be used with an insecure 
attachment.
Do not use the 3D Conversion Lens 
without adjusting it first.
≥It will not be possible to record 3D video 
correctly, and this may lead to tiredness or 
discomfort.
≥ When you re-attach the 3D Conversion 
Lens after removing it, we recommend 
making the adjustments again.
With the 3D Conversion Lens attached, 
do not record a subject at less than the 
minimum focus distance.
≥ The 3D effects may be more pronounced, 
and therefore cause tiredness or 
discomfort.
≥ The minimum focus distance is approx. 
1.2 m (3.9 feet).
When recording with the 3D Conversion 
Lens attached, be careful not to shake 
the unit.
≥ Tiredness or discomfort may result if the 
shake is pronounced, due to riding in a 
vehicle or walking etc.
≥ When moving the unit as you record, 
move it slowly.
≥ We recommend using a tripod.
About 3D viewingAnyone who is hyper sensitive to light, 
suffers from heart disease or is otherwise 
unwell should avoid viewing 3D video.
≥Doing may have an adverse affect on 
such medical conditions.
If you feel tired, uncomfortable or 
otherwise strange when viewing 3D 
video, stop viewing at once.
≥ Continuing to view may cause illness.
≥ Please rest appropriately after stopping 
the viewing. When viewing 3D video, we recommend 
taking a break every 30 to 60 minutes.
≥
Viewing for extended periods may cause 
eye-fatigue.
Short-sighted or far-sighted persons, 
those with differences in the sight of their 
right and left eyes, and those with 
astigmatism are advised to correct their 
vision by wearing glasses etc.
Stop viewing if you can clearly see a 
double image while viewing 3D video.
≥ There are differences in the way that 
different people experience 3D video 
images. Please correct your sight 
appropriately before viewing 3D video.
≥ You can change the 3D setting of your 
television or 3D output setting of the unit 
to 2D.
When viewing 3D video on a 3D 
compatible television, position yourself a 
distance away that is at least 3 times the 
effective height of the television.
≥ (Recommended distance): 
For 42 z; approx. 1.6 m (5.2 feet), 
for 46 z; approx. 1.7 m (5.6 feet),
for 50 z; approx. 1.9 m (6.2 feet), 
for 54 z; approx. 2.0 m (6.6 feet).
≥ Viewing from a distance closer than the 
recommended distance may lead to eye-
fatigue.
Viewing of 3D video is not recommended 
for children under 5 to 6 years.
≥ It is difficult to know how children will react 
to tiredness or discomfort, and they may 
become ill suddenly.
≥ When children are viewing, have a 
responsible adult ensure that eye-fatigue 
does not occur.
About 3D
HDCSD800P-VQT3K35_mst.book  145 ページ  ２０１０年１２月２０日　月曜日　午前９時４分 
						

							146VQT3K35
When disposing of or giving away the SD 
card, note that:
≥Formatting and deletion of this unit or 
computer only changes the file 
management information and does not 
completely delete the data in the SD card.
≥ It is recommended that the SD card is 
physically destroyed or the SD card is 
physically formatted using this unit when 
disposing of or giving away the SD card.
To physically format the SD card, connect 
the unit via the AC adaptor, select 
[SETUP]  #[FORMAT CARD]  # [YES] 
from the menu, and then press and hold 
the recording start/stop button on the 
screen below for about 3 seconds. When 
the SD card data deletion screen appears, 
select [YES], and then follow the on-
screen instructions.
≥ The customer is responsible for the 
management of the data in the SD card. ≥
When the LCD monitor gets dirty, wipe it 
with a soft cloth such as eye glass cleaner.
≥ Do not touch the LCD monitor with your 
finger nails, or rub or press with strong 
force.
≥ It may become hard to see or hard to 
recognize the touch when the LCD 
protection sheet is affixed.
≥ In a place with drastic temperature 
changes, condensation may form on the 
LCD monitor. Wipe it with a soft cloth such 
as eye glass cleaner.
≥ When the unit has become very cold, for 
example due to storage in a cold area, its 
LCD monitor will be slightly darker than 
usual immediately after the unit is turned 
on. The normal brightness will be restored 
when the unit’s internal temperature rises.
About the SD cardLCD monitor
Extremely high precision technology is 
employed to produce the LCD Monitor 
screen featuring a total of approximately 
230,000 dots. The result is more than 
99.99% effective dots with a mere 0.01% 
of the dots inactive or always lit. 
However, this is not a malfunction and 
does not affect the recorded picture.
HDCSD800P-VQT3K35_mst.book  146 ページ  ２０１０年１２月２０日　月曜日　午前９時４分 
						

							147VQT3K35
After you have set up the face recognition 
function, personal information will be held in 
this unit and included in recorded images.
≥When the unit is serviced, or given away/
disposed of, the personal information 
should be deleted in the interests of 
protecting personal information. ( l94)
Indemnity
≥ Information, including personal 
information, may be changed or lost as a 
result of mistaken operation, static 
electricity effects, accident, breakage, 
repair or other handling.
It should be noted before use that 
Panasonic does not accept any 
responsibility for direct or indirect 
problems which occur as the result of the 
change to or loss of the information 
including personal information. When condensation forms on the unit, the 
lens will cloud up and the unit may not work 
properly. Make every effort to ensure that 
condensation does not form. If it does form, 
take the actions described below.
Causes of condensationCondensation takes place when the 
ambient temperature or humidity is 
changed as follows.
≥
When this unit is brought inside from the 
cold (e.g. a ski slope) to a warm room.
≥ When this unit is moved from an 
air-conditioned car to outside.
≥ When a cold room has been warmed up 
quickly.
≥ When cool wind from an air conditioner is 
directly blown onto this unit.
≥ After rain showers.
≥ When this unit is in a very humid place 
where the air is thick with steam. (e.g. a 
heated swimming pool)
Helpful hint
If, for example, you have used this unit for 
recording on a ski slope and are taking it into 
a heated room, place the unit inside a plastic 
bag, remove as much of the air from inside 
the bag as possible, then seal the bag. 
Leave the unit for about an hour in the room 
so the temperature of the unit is close to the 
ambient temperature of the room, then use 
it.
About personal informationAbout condensation
HDCSD800P-VQT3K35_mst.book  147 ページ  ２０１０年１２月２０日　月曜日　午前９時４分 
						

							148VQT3K35
∫Carefully observe copyright 
laws
Whatever you have recorded and created 
can be used for your personal 
entertainment only. Under copyright 
laws, other materials cannot be used 
without obtaining permission from the 
holders of the copyrights.
∫Licenses
≥SDXC Logo is a trademark of SD-3C, 
LLC.
≥ “AVCHD” and the “AVCHD” Logo are 
trademarks of Panasonic Corporation and 
Sony Corporation.
≥ Manufactured under license from Dolby 
Laboratories.
Dolby and the double-D symbol are 
trademarks of Dolby Laboratories.
≥ HDMI, the HDMI Logo, and High-
Definition Multimedia Interface are 
trademarks or registered trademarks of 
HDMI Licensing LLC in the United States 
and other countries.
≥ VIERA Link
™ is a trademark of Panasonic 
Corporation.
≥ EZ Sync
™ is a trademark of Panasonic 
Corporation.
≥ HDAVI Control
™ is a trademark of 
Panasonic Corporation.
≥ x.v.Color
™ is a trademark.
≥ LEICA is a registered trademark of Leica 
Microsystems IR GmbH and DICOMAR is 
a registered trademark of Leica Camera 
AG.
≥ Microsoft
®, Windows® and Windows 
Vista® are either registered trademarks or 
trademarks of Microsoft Corporation in the 
United States and/or other countries.
≥ Microsoft product screen shot(s) reprinted 
with permission from Microsoft 
Corporation. ≥
IBM and PC/AT are registered trademarks 
of International Business Machines 
Corporation of the U.S.
≥ Intel
®, Core™, Pentium® and Celeron® are 
the registered trademarks or trademarks 
of Intel Corporation in the United States 
and other countries.
≥ AMD Athlon
™ is a trademark of Advanced 
Micro Devices, Inc.
≥ iMovie and Mac are trademarks of 
Apple Inc., registered in the U.S. and 
other countries.
≥ Other names of systems and products 
mentioned in these instructions are 
usually the registered trademarks or 
trademarks of the manufacturers who 
developed the system or product 
concerned.
This product is licensed under the AVC 
patent portfolio license for the personal and 
non-commercial use of a consumer to (i) 
encode video in compliance with the AVC 
Standard (“AVC Video”) and/or (ii) decode 
AVC Video that was encoded by a consumer 
engaged in a personal and non-commercial 
activity and/or was obtained from a video 
provider licensed to provide AVC Video. No 
license is granted or shall be implied for any 
other use. Additional information may be 
obtained from MPEG LA, LLC. 
See http://www.mpegla.com
.
Others
About copyright
HDCSD800P-VQT3K35_mst.book  148 ページ  ２０１０年１２月２０日　月曜日　午前９時４分 
						

							149VQT3K35
≥SD cards are only mentioned with their main memory size. The stated times are the 
approximate recordable times for continuous recording.
A Favors image quality
B Favors recording time
≥ If recording for long periods, prepare batteries for 3 or 4 times the period you wish to record 
for. ( l21)
≥ The default setting is [HG] Mode.
≥ Recordable time of 3D recording mode is the same.
(During 3D recording mode, 1080/60p and iFrame recording mode cannot be used.)
≥ Maximum continuously recordable time for one scene: 12 hours
≥ The recording is paused once when the recording time for one scene exceeds 12 hours, 
and the recording will automatically resume after a few seconds.
≥ If a recording with a lot of action is recorded, the recording time is reduced.
≥ The recordable time may be reduced if recording of short scene is repeated.
≥ Use time in the row of 4 GB in above table as a guideline for the time that can be copied 
onto one DVD disc (4.7 GB).
Others
Recording modes/approximate 
recordable time
Recording mode[1080/60p][HA][HG][HX][HE]
Picture size1920k10801920k10801920k10801920k10801920k1080
SD card 4GB
19min 30min 40min 1h 1h30min
16 GB 1h20min 2h 2h40min 4h10min 6h40min
64 GB 5h20min 8h30min 11h
16 h 50 min 27 h 30 min
Recording mode[iFrame]
Picture size960k540
SD card 4GB
19 min
16 GB 1h20min
64 GB 5h20min


HDCSD800P-VQT3K35_mst.book  149 ページ  ２０１０年１２月２０日　月曜日　午前９時４分 
						

							150VQT3K35
≥SD cards are only mentioned with their main memory size. The stated number is the 
approximate number of recordable pictures.
(When [ASPECT RATIO] is set to [4:3] and [QUALITY] is set to  )
(When [ASPECT RATIO] is set to [3:2] and [QUALITY] is set to  )
(When [ASPECT RATIO] is set to [16:9] and [QUALITY] is set to  )
≥ When [QUALITY] is set to  , the numbers of recordable pictures are larger than the 
numbers shown in the table above.
≥ The number of recordable pictures depends on whether   and   are used 
together and on the subject being recorded.
≥ Maximum number of recordable pictures that can be displayed is 99999.
If the number of recordable pictures exceeds 99999, the number will not change when the 
picture is taken until the number of recordable pictures gets less than 99999.
≥ The memory capacity indicated on the label of an SD card is the total of the capacity for 
copyright protection and management and the capacity which can be used on the unit, a 
PC etc.
Others
Approximate number of recordable 
pictures
Picture size4032k 30243200k24002560k1920640 k480
SD card
4GB 610 940 1500 30000
16 GB25003900 6200 122000
64 GB 10000 15800 25000 492000
Picture size4608k30723600k24002880k1920
SD card
4GB 500 850 1300
16 GB21003400 5500
64 GB 8400 14000 22000
Picture size4864k27363840k21603072k17281920k 1080
SD card
4GB 550 850 1420 3600
16 GB22003400 5600 1400064 GB 9000 14000 23000 59000
12 .2M7.7M4.9M0.3M
14.2M8.6M5.5M
13.3M8.3M5.3M2.1M
HDCSD800P-VQT3K35_mst.book  150 ページ  ２０１０年１２月２０日　月曜日　午前９時４分