Panasonic Hdc Sd600p Operating Instructions

							121VQT2U72
Others
Indications
1
Indications
∫Recording indications
Motion Picture Recording Mode
Still Picture Recording Mode
Remaining battery power 
(l 21)
1h30m Remaining battery time 
(l 21)
R 1h20m Remaining time for motion 
picture recording ( l30)
0h00m00s Elapsed recording time 
(l 30)
NOV 15 2010
12:34PM Date indication (
l27)
Time indication ( l27)
World time setting ( l40)
///
Motion picture recording mode ( l60)
1080/60p recording ( l52)
 (White)
 (Green) Card recording possible 
status
Recognizing the card
0h00m00s
99 99%
â
99% â1/100OPEN
0dB
MFR 1h20m1h30mAHG1920
NOV  15 2010 12:34PMF
1/100OPEN
0dB
MNLMEGAMFR 30001h30mA
99 99%
â
99% â
F
14.2M
¥/; (Red) Recording
; (Green) Recording pause
PRE-REC (l54)
Interval Recording ( l61)
Manual Mode (l 76)
////////
Intelligent Auto Mode ( l33)
/ Operation icon is displayed/
not displayed. ( l53)
MF Manual Focus ( l79)
// / / /
White Balance ( l77)
1/100 Shutter Speed ( l78)
OPEN/F2.0 Iris value (l78)
0dB Gain value (l78)
5//////// //
Scene Mode ( l59)
///
Power LCD ( l43)
//// /
Image Stabilizer (l 50)
/ AF/AE tracking ( l51)
Zebra ( l69)
Picture adjustment ( l69)
Digital Cinema ( l62)
Hi-Speed Burst Shooting 
( l 74)
Digital cinema color ( l66)
AF assist lamp ( l75)
Zoom Microphone ( l67)
Wind Noise Canceler ( l67)
PRE-REC
MNL
FF
AW B
+2+1-1A
HDC-SD600-P-VQT2U72_mst.book  121 ページ  ２０１０年４月１４日　水曜日　午後３時２８分 
						

							122VQT2U72
∫Playback indications/ Smile Shot (l 55)
Microphone Level ( l68)
Backlight Compensation 
( l 57)
Soft Skin Mode ( l57)
Tele Macro ( l58)
/ Fade (White), Fade (Black) 
(l 54)
Color Night Rec function 
( l 58)
Intelligent Contrast Control 
( l 54)
Intelligent Exposure ( l57)
99% Luminance Level ( l70)
±  (White)/ ¥ (Green)/ / / / /
Focus indication ( l31)
Ø10/ Ø2 Self-Timer Recording (l 57)
ß /ß A/ Flash (l56)
ß i /ß j Flash Level ( l56)
Red-Eye Reduction ( l56)
/ Picture Quality ( l73)
//// / / / / / /
Number of recording pixels for still pictures 
( l 32, 72, 74, 81)
In Playback Mode, the picture size is not 
displayed for still pictures recorded with 
other products that have different picture 
sizes from the sizes shown above.
R3000 Remaining number of still 
pictures (l32)
 (White)
 (Red) Still picture recording 
possible status
Recording still picture
MEGA OIS (
l31)
12 .2M7.7M4.9M0.3M14.2M8.6M5.5M13.3M8.3M5.3M2.1M
MEGA
1/;/ 5 // 6// 7/8/9 /: /
D /E /;1 /2;
Display during playback ( l35, 80)
/ Operation icon is displayed/
not displayed. ( l35)
0h00m00s Playback Time ( l35)
No.10 Scene Number
Repeat Playback ( l82)
Resume Playback ( l83)
100-0001 Still picture folder/file name
1 DPOF already set
(to more than 1) ( l93)
Protected motion pictures/
still pictures ( l92)
1080/60p recorded scene 
( l 36)
Interval-recorded scene 
( l 61)
Still picture recorded using 
Smile Shot ( l55)
FF
HDC-SD600-P-VQT2U72_mst.book  122 ページ  ２０１０年４月１４日　水曜日　午後３時２８分 
						

							123VQT2U72
∫Indication of connection to 
other devices
∫ Confirmatory indications
∫ Confirmatory indications when 
a DVD burner is connected
Accessing the card ( l11 7 )
–– (Time 
display) The built-in battery is low. 
(
l 27)
Warning recording yourself 
( l 26)
Disc Playback ( l105)
Scene copied in [Standard]([XP])
Scene copied in [Standard]([SP])
//////
Disc type ( l100)
Unusable disc
XP
SP
HDC-SD600-P-VQT2U72_mst.book  123 ページ  ２０１０年４月１４日　水曜日　午後３時２８分 
						

							124VQT2U72
Others
Indications
2
Messages
Major confirmation/error messages to be indicated on the screen in text.
CHECK CARD.
This card is not compatible or it cannot be recognized by the unit.
If this message appears even though motion pictures and still pictures are recorded on 
an SD card, the card may be unstable. Reinse rt the SD card, then turn the unit off and 
then on again.
THIS BATTERY CANNOT BE USED.
≥ Use a battery that is compatible with this unit. ( l18)
If using a Panasonic battery compatible with this unit, remove the battery and then 
insert it again. If the message appears even after repeating this several times, this unit 
needs repair. Detach the power and contact consumer support. ( l150) Do not attempt 
to repair it by yourself.
≥ You are attempting to connect an AC adaptor not compatible with this unit. Use the 
supplied AC adaptor. ( l21)
PLEASE CHECK EXTERNAL DRIVE OR DISC.
A disc that cannot be used when connecting the unit to the DVD burner has been 
inserted, or the DVD burner is not recognized properly. Connect the Mini AB USB 
Connection Cable again and insert a disc to copy the data. ( l100)
HDC-SD600-P-VQT2U72_mst.book  124 ページ  ２０１０年４月１４日　水曜日　午後３時２８分 
						

							125VQT2U72
If faulty management information is found, the messages may appear and a repair is 
performed. (Repairing may take time depending on the error.)
≥The above message is displayed when abnormal management information is detected 
when the scenes are displayed in thumbnail. To perform the repair, touch the scene with 
 in the thumbnail, and start the playback. Please be aware that if the repair fails, 
scenes with   will be deleted.
≥ Use a sufficiently charged battery or the AC adaptor.
≥ Depending on the condition of the data, it may not be possible to completely repair the 
data.
≥ When data recorded on another device is recovered, it may not be possible to play back 
the data on this unit or the other device.
≥ If recovery fails, turn the unit off and on again after waiting a while. If recovery fails 
repeatedly, format a media on the unit. Please be aware that if a media is formatted, then 
all the data recorded on the media will be erased.
≥ If the thumbnail information is recovered, displaying the thumbnails may become slower.
About recovery
SOME SCENES NEED REPAIRING. PLAY SCENES TO BE REPAIRED. 
(IRREPARABLE SCENES WILL BE DELETED.)
HDC-SD600-P-VQT2U72_mst.book  125 ページ  ２０１０年４月１４日　水曜日　午後３時２８分 
						

							126VQT2U72
Others
Troubleshooting
ProblemCheck points
This unit cannot be 
turned on.
This unit does not stay 
on long enough.
Battery runs down 
quickly. ≥
Charge the battery again to ensure it is sufficiently 
charged. ( l18)
≥ In cold places, the battery using time becomes 
shorter.
≥ The battery has a limited life. If the operating time is 
still too short even after the  battery is fully charged, 
the battery has worn out and needs to be replaced.
This unit is turned off 
automatically. ≥
If the unit turns off when you turn off the power to the 
TV using the TV remote control, the VIERA Link is at 
work. If you are not using the VIERA Link, set 
[VIERA Link] to [OFF]. ( l98)
≥ When this unit is connected to a DVD burner to copy 
or play back images (a disc is being accessed), the 
unit turns off automatically if the Mini AB USB 
Connection Cable is removed.
A clicking sound is 
heard when the unit is 
shaken. ≥
This is the sound of the lens moving and is not a 
defect.
This sound will no longer be heard when the unit is 
turned on and change the mode to   or  .
Remaining battery 
indication is not 
displayed properly. ≥
The remaining battery capacity indication is an 
approximation.
If the remaining battery capacity indication is not 
displayed correctly, fully charge the battery, 
discharge it and then charge it again.
This unit cannot be 
operated though it is 
turned on.
This unit does not 
operate normally. ≥
Remove the battery or AC adaptor, wait about 
1 minute and then reconnect the battery or AC 
adaptor. Then about 1 minute later, turn on the unit 
again. (Conducting the above operation while the 
media is being accessed may damage the data on 
the media.)
≥ If normal operation is still not restored, detach the 
power connected, and contact consumer support. 
(l 150)
HDC-SD600-P-VQT2U72_mst.book  126 ページ  ２０１０年４月１４日　水曜日　午後３時２８分 
						

							127VQT2U72
ProblemCheck points
Item other than the 
touched one is 
selected. ≥
Calibrate the touch screen. ( l45)
The remote control 
does not function. ≥
[REMOTE CONTROL] of the [SETUP] is [OFF]. 
(l 47)
≥ The button-type battery of the remote control may 
have run out. Replace it with a new button-type 
battery. ( l47)
The remaining time 
indication or the 
elapsed time 
indication is not 
shown. ≥
[DISPLAY] of the [SETUP] is [OFF]. ( l40)
The unit arbitrarily 
stops recording. ≥
Use an SD card that can be used for motion picture 
recording. ( l22)
≥ The recordable time may have shortened due to the 
deterioration of the data writing speed or repeated 
recording and deletion. Using the unit, format the SD 
card. ( l45)
≥ If [AGS] is [ON], record in the normal horizontal 
position or set [AGS] to [OFF]. ( l66)
Auto focus function 
does not work. ≥
Switch to Intelligent Auto Mode.
≥ If you are trying to record a scene which is hard to 
bring into focus in Auto Focus Mode, use the Manual 
Focus Mode to adjust the focus. ( l34, 79)
Color balance of 
images is strange 
when recording in a 
place such as a 
gymnasium. ≥
In a place with multiple light sources, such as a 
gymnasium or a hall, set the white balance setting to 
 (Indoor mode 2). If you cannot record clearly 
with the   (Indoor mode 2), set it to   (Manual 
adjustment mode). ( l77)
Any scenes/still 
pictures cannot be 
played back. ≥
Any scenes/still pictures where the thumbnails are 
displayed as   cannot be played back.
HDC-SD600-P-VQT2U72_mst.book  127 ページ  ２０１０年４月１４日　水曜日　午後３時２８分 
						

							128VQT2U72
Although this unit is 
correctly connected to 
a TV, images cannot 
be seen.
The images are 
squeezed horizontally.≥
Please read the operating instructions of your TV 
and select the channel that matches the input used 
for the connection.
≥ Change the [TV ASPECT] setting to match the 
aspect ratio of the TV. ( l96)
≥ Change the setting of the unit depending on the 
cable connecting to the TV. ( l97)
Scenes cannot be 
deleted. ≥
Release the protect setting. ( l92)
≥ Any scenes/still pictures where the thumbnails are 
displayed as   cannot be deleted. If the scenes/
still pictures are unnecessary, format the media to 
erase the data. ( l45) Please be aware that if a 
media is formatted then all the data recorded on the 
media is erased and cannot be recovered. Back up 
important data on a PC, disc etc.
If the SD card is 
inserted in this unit, it 
is not recognized. ≥
If the SD card is formatted on a PC, it may not be 
recognized by this unit. Use this unit to format SD 
cards. ( l45)
If the SD card is 
inserted in another 
device, it is not 
recognized. ≥
Check that the device is compatible with the capacity 
or type of SD card (SD Memory Card/SDHC Memory 
Card/SDXC Memory Card) that you inserted. Refer 
to the operating instructions of the device for details.
Color or brightness of 
the image changes, or 
you may see 
horizontal bars in the 
image.
The LCD monitor 
flickers indoors. ≥
Color or brightness of the image may change, or you 
may see horizontal bars in the image when the 
object is recorded under fluorescent light, mercury 
light or sodium light, etc., but this is not a 
malfunction.
≥ In Motion Picture Recording Mode, record in 
Intelligent Auto Mode or set the shutter speed to 
1/60 in areas where the power supply frequency is 
60 Hz, or 1/100 in areas of 50 Hz.
≥ In Still Picture Recording Mode, this will not affect the 
recorded image.
ProblemCheck points
HDC-SD600-P-VQT2U72_mst.book  128 ページ  ２０１０年４月１４日　水曜日　午後３時２８分 
						

							129VQT2U72
Object seems to be 
warped.≥
Object seems to be warped slightly when the object 
moves across the image very fast, but this is 
because the unit is using MOS for the image sensor. 
This is not a malfunction.
White round spots like 
soap bubbles appear 
on the recorded 
picture. ≥
If you take a picture 
with the flash in a dark 
place or indoors, white 
round spots may 
appear on the picture 
caused by the flash 
reflecting of particles of dust in the air. This is not a 
malfunction.
A characteristic of this is that the number of round 
spots and their position differ in every picture.
“ERROR OCCURRED. 
PLEASE TURN UNIT 
OFF, THEN TURN ON 
AGAIN.” is displayed. ≥
The unit has automatically detected an error. Restart 
the unit by turning the unit off and on.
≥ The unit will be turned off in about 1 minute if the unit 
is not turned off and on.
≥ Repair is needed if it is repeatedly displayed even if 
it is restarted. Detach the power connected, contact 
consumer support. ( l150) Do not attempt to repair 
the unit by yourself.
VIERA Link does not 
work. [Setting on this unit]
≥
Connect with a HDMI mini cable (optional). ( l98)
≥ Press the MENU button, then touch [SETUP]  # 
[VIERA Link]  # [ON]. ( l98)
≥ Turn the unit off and then back on again.
[Setting on other devices]
≥ If the TV input does not switch automatically, switch 
the input using the TV remote control.
≥ Check the VIERA Link setting on the connected 
device.
≥ Please refer to the operating instructions of the 
connected device.
ProblemCheck points
HDC-SD600-P-VQT2U72_mst.book  129 ページ  ２０１０年４月１４日　水曜日　午後３時２８分 
						

							130VQT2U72
When connected by 
the USB cable, this 
unit is not detected by 
the PC.≥
After re-inserting the SD card into the unit, reconnect 
the supplied USB cable.
≥ Select another USB terminal on the PC.
≥ Check the operating environment. ( l111 )
≥ Connect the supplied USB cable again after 
restarting the PC and turning on this unit again.
When the USB cable is 
disconnected, an error 
message will appear 
on the PC. ≥
To disconnect the USB cable safely, double-click the 
 icon in the task tray and follow the instructions 
on the screen.
The power of the DVD 
burner cannot be 
turned on. ≥
When the unit is connected to the DVD burner, use 
the respective AC adaptors for both this unit and the 
DVD burner.
Cannot see the PDF 
operating instructions 
for HD Writer AE 2.1. ≥
You will need Adobe Acrobat Reader 5.0 or later or 
Adobe Reader 7.0 or later to read the PDF operating 
instructions for HD Writer AE 2.1.
Cannot copy scenes 
on the SD card by 
connecting to other 
equipment with the 
USB cable. ≥
Other equipment might have not recognized the SD 
card. Unplug the USB cable once, and reconnect it.
ProblemCheck points
HDC-SD600-P-VQT2U72_mst.book  130 ページ  ２０１０年４月１４日　水曜日　午後３時２８分