Panasonic Hd Plasma Display Th 50pf10 Operating Instructions

41
SET UP for PORTRAIT
Press to select VIEWING AREA or LOCATION.
Press to select each function.
Notes:
•  When the input signal is FULL, VIEWING AREA is fi xed to “16:9”.
•  When “VIEWING AREA”is “16:9”, the aspect mode is set to “FULL”.
Press twice to exit from SET UP.7
6
Press to select AI-SYNCHRONIZATION.
Press to select “OFF” , “ON”. Adjust to equalize the brightness of the 3 displays when using PORTRAIT setting. 
The brightness depends on 
each display’s setting.Equalize the brightness of 
all the...

42
SET UP for Input Signals
3D Y/C FILTER – For NTSC AV images
COMPONENT / RGB IN SELECT
Select to match the signals from the source connected to the COMPONENT / RGB input terminals.
Y,  P
B, PR signals   “COMPONENT”
R, G, B, HD, VD signals   “RGB”
Press to display the SET UP menu.
Press to select the “COMPONENT / RGB-IN 
SELECT”.
Press to select the desired mode.
COMPONENT  RGB
Press to exit from adjust mode.
Select “SIGNAL” from the “SET UP” menu during VIDEO (S VIDEO) input signal mode.
(“SIGNAL...

43
3D Y/C FILTER (NTSC) 
COLOR SYSTEM 
SIGNAL 
AUTO 3 : 2 PULLDOWN 
Panasonic AUTO (4 : 3) OFF 
NORMAL 
[ 
VIDEO ] 
VIDEO NR 
OFF 
REFRESH RATE
100 Hz
Block NR
Mosquito NROFF
OFF
SYNC 
VIDEO NR
SIGNAL 
AUTO 
H-FREQ.
V-FREQ.kHz
Hz33.8
60.0
[ 
RGB ] 
3 : 2 PULLDOWNOFF
OFF
REFRESH RATE
100 Hz
Block NR
Mosquito NROFF
OFF
3 : 2 PULLDOWN 
VIDEO NR 
SIGNAL 
OFF 
REFRESH RATE
100 HzOFF 
Block NR
Mosquito NROFF
OFF
 [ 
COMPONENT ] 
3 : 2 PULLDOWN 
VIDEO NR 
SIGNAL 
OFF 
OFF 
H-FREQ.
V-FREQ.kHz
Hz33.8
60.0
[...

44
3:2 PULLDOWN COLOR SYSTEM / Panasonic AUTO
Select SIGNAL from the “SET UP” menu during VIDEO (S VIDEO) input
signal mode.(“SIGNAL [VIDEO]” menu is displayed.)
SET UP for Input Signals
Press to select the “COLOR SYSTEM” or “Panasonic 
AUTO”.
Press to select each function.
If the image becomes unstable:
With the system set on Auto, under conditions of low 
level or noisy input signals the image may in rare 
cases become unstable. Should this occur, set the 
system to match the format of the input...

45
SET UP for Input Signals
Select SIGNAL from the “SET UP” menu during RGB input signal.
Press to adjust.
Press to exit from adjust mode.
SYNC
Setting RGB sync signal
Confi rm that the input is set to RGB INPUT (this setting is valid only for RGB INPUT 
signal).
AUTO:  The H and V sync or synchronized signal are automatically selected. 
If both input, it is selected the H and V sync.
ON G:  Uses a synchronized signal on the Video G signal, which is input from 
the G connector.
VBS:  Uses a synchronized...

46
1
2
3
5Press to display the Setup menu.
4
6
Item Effect Adjustments
Weekly 
Command 
TimerSets Weekly Command Timer. (see page 50)
Onscreen 
display
On Off
On:  Displays all the following on screen.
• Power on display
• Input signal switch display
• No signal display
• Mute and the remaining time of off-timer after 
 was pressed.
Off:  Hides all the items above from view.
Initial INPUTOff  PC  INPUT1  INPUT2  INPUT3 
Adjusts the input signal when the unit is turned on.
Notes:
• Only the adjusted...

47
Item Effect Adjustments
Initial VOL 
level
Off On
Press  button to adjust the volume when the unit is turned on.
Off  On
Off:  Sets normal volume.
On:  Sets your preferred volume.
Notes:
• 
When “Maximum VOL level” is “On”, the volume can only be adjusted between 0 and your maximum range.•  You can hear the changed volume regardless of your volume setting before opening the options menu 
if you adjust the volume when “Initial VOL level” is “On” and cursor is on the menu.
Maximum VOL 
level
Off On...

48
Item Effect Adjustments
Off-timer 
function
EnableDisable
Enable:  Enables the “Off-timer function”.
Disable:  Disables the “Off-timer function”.
Note:    When “Disable” is set, the Off-timer is cancelled.
Initial Power 
ModeNormal  Standby  On
Sets the power mode of the unit for when the power recovers from failure or after plugging off and in again.Normal:  Power returns in as the same state as before the power interruption.
Standby:  Power returns in standby mode. (Power Indicator : red/orange)
On:...

49
Item Effect Adjustments
Slot PowerOff  Auto  On 
Off:  Power is not transmitted to the slot power.
Auto:  Power is transmitted to the slot power only when main power is on.
On:  Power is transmitted to the slot power when main power is on or in the standby state.
Note:  In some cases, power is transmitted to the slot power when main power is on or in the standby 
state regardless of the slot power setting.
Power On 
Screen DelayOff   1   2   3....   30 
You can set the power-on delay time of the...

50
Options 
On Weekly Command TimerOnscreen display 
1/3 
 
Weekly Command Timer 
On Program1Function Monday 
Program3Tuesday --- Wednesday Program3Thursday --- Friday Program6Saturday Program4Sunday Program Edit 
Weekly Command Timer 
Program1On Monday Function 
Program3Tuesday 
--- Wednesday Program3Thursday --- Friday Program6Saturday Program4Sunday Program Edit 
Program3Thursday --- Friday Program6Saturday Program4Sunday Program Edit 
Weekly Command Timer 
8:00 
10:30 01
02
1/8
--:-- 03--:-- 04--:--...