Panasonic Hd Plasma Display Th 50pf10 Operating Instructions

							41
SET UP for PORTRAIT
Press to select VIEWING AREA or LOCATION.
Press to select each function.
Notes:
•  When the input signal is FULL, VIEWING AREA is fi xed to “16:9”.
•  When “VIEWING AREA”is “16:9”, the aspect mode is set to “FULL”.
Press twice to exit from SET UP.7
6
Press to select AI-SYNCHRONIZATION.
Press to select “OFF” , “ON”. Adjust to equalize the brightness of the 3 displays when using PORTRAIT setting. 
The brightness depends on 
each display’s setting.Equalize the brightness of 
all the displays.
OFF ON
Note:
If you set AI-SYNCHRONIZATION to ON, the following menus will be unavailable and these settings will be fi xed to the 
initial values.
PICTURE menu: COLOR, TINT
AI-SYNCHRONIZATION
OFF PORTRAIT SETUP
SEAM HIDES VIDEOOFF 
1
OFF
AI-SYNCHRONIZATION VIEWING AREA
LOCATION16:9
PORTRAIT SETUP
OFF PORTRAIT SETUP
SEAM HIDES VIDEOOFF 
1
OFF
AI-SYNCHRONIZATION VIEWING AREA
LOCATION16:9
PORTRAIT SETUP
5
VIEWING AREA: Set a mode of image division for PORTRAIT function.
LOCATION:    Set a location of image to be displayed for PORTRAIT function.
VIEWING AREA / LOCATION
When PORTRAIT SETUP “ON”:
Display the image of the selected LOCATION.When PORTRAIT SETUP is “OFF”:
Represent an area of the selected LOCATION at a normal 
brightness and darken the rest of it. LOCATION setting
VIEWING AREA and LOCATION
The mode of image division and the LOCATION by setting of VIEWING AREA is as follows. 
LOCATION 1 LOCATION 2 LOCATION 3
LOCATION 1 LOCATION 2 LOCATION 3 VIEWING AREA:  4:3Suitable to display FULL images. NORMAL 
(4:3) images extend transversely.
Both right and left sides of the image are 
cut by 48 dots. VIEWING AREA:  16:9
4:3 images are displayed without changing 
aspect ratio. 
Although the images of each LOCATION 
overlap, you can adjust POS. / SIZE to 
display the image normally. (see page 22) Undisplayed area (48 dots) 
						

							42
SET UP for Input Signals
3D Y/C FILTER – For NTSC AV images
COMPONENT / RGB IN SELECT
Select to match the signals from the source connected to the COMPONENT / RGB input terminals.
Y,  P
B, PR signals   “COMPONENT”
R, G, B, HD, VD signals   “RGB”
Press to display the SET UP menu.
Press to select the “COMPONENT / RGB-IN 
SELECT”.
Press to select the desired mode.
COMPONENT  RGB
Press to exit from adjust mode.
Select “SIGNAL” from the “SET UP” menu during VIDEO (S VIDEO) input signal mode.
(“SIGNAL [VIDEO]” menu is displayed.)
Note:
When ON, this setting only affects NTSC input signals. Note:
Selection may not be possible, depending on which optional board is installed.
1
2
1/2
PC
OFF
STANDBY SAVE
OFF
POWER MANAGEMENTOFF
AUTO POWER OFF
OFF
OSD LANGUAGEENGLISH (
US) COMPONENT/RGB-IN SELECT
RGB
INPUT LABELSIGNAL
POWER SAVE
SET UP
1/2
PC
OFF
STANDBY SAVE
OFF
POWER MANAGEMENTOFF
AUTO POWER OFF
OFF
OSD LANGUAGEENGLISH (
US) COMPONENT/RGB-IN SELECT
RGB
INPUT LABELSIGNAL
POWER SAVE
SET UP
3D Y/C FILTER (NTSC)
COLOR SYSTEM
SIGNAL
ON
AUTO
3 : 2 PULLDOWN
Panasonic AUTO (4 : 3)OFF
NORMAL
[ 
VIDEO ]
VIDEO NR
OFF
3
1
2
Press ACTION  (  ) button Press to select the “3D Y/C FILTER (NTSC)”.
Press to set ON / OFF.
Press to exit from adjust mode. 
						

							43
3D Y/C FILTER (NTSC) 
COLOR SYSTEM 
SIGNAL 
AUTO 3 : 2 PULLDOWN 
Panasonic AUTO (4 : 3) OFF 
NORMAL 
[ 
VIDEO ] 
VIDEO NR 
OFF 
REFRESH RATE
100 Hz
Block NR
Mosquito NROFF
OFF
SYNC 
VIDEO NR
SIGNAL 
AUTO 
H-FREQ.
V-FREQ.kHz
Hz33.8
60.0
[ 
RGB ] 
3 : 2 PULLDOWNOFF
OFF
REFRESH RATE
100 Hz
Block NR
Mosquito NROFF
OFF
3 : 2 PULLDOWN 
VIDEO NR 
SIGNAL 
OFF 
REFRESH RATE
100 HzOFF 
Block NR
Mosquito NROFF
OFF
 [ 
COMPONENT ] 
3 : 2 PULLDOWN 
VIDEO NR 
SIGNAL 
OFF 
OFF 
H-FREQ.
V-FREQ.kHz
Hz33.8
60.0
[ 
Digital ] 
REFRESH RATE
100 Hz
Block NR
Mosquito NROFF
OFF
REFRESH RATE
Press to select REFRESH RATE.
Press to adjust.
Press to exit from adjust mode. This function sets the refresh rate of the display.
This menu is displayed when the input signal is 50 Hz system (50i, 50p, 25p, 24p, 24sF) of vertical scan rate.
100 Hz: Reduce screen fl icker.
50 Hz: Enhance the resolution of moving images.
Note: 
It is recommended to set to 100 Hz normally.
1
2
Press to select VIDEO NR, Block NR or Mosquito NR.
Press to select “OFF”, “MIN” , “MID” , “MAX”.
Press to exit from adjust mode. VIDEO NR:    Automatically reduces unwanted picture noise.
Block NR:    Reduces block noise when playing MPEG videos.
Mosquito NR: Reduces mosquito noise around subtitles on MPEG videos.
Note: 
VIDEO NR cannot be adjusted while a PC signal is being applied.
1
2
SET UP for Input Signals
VIDEO NR / Block NR / Mosquito NR
1/2
PC
OFF
STANDBY SAVE
OFF
POWER MANAGEMENTOFF
AUTO POWER OFF
OFF
OSD LANGUAGEENGLISH (
US) COMPONENT/RGB-IN SELECT
RGB
INPUT LABELSIGNAL
POWER SAVE
SET UP
Press ACTION  (  ) button
3D Y/C FILTER (NTSC) 
COLOR SYSTEM 
SIGNAL 
ON 
AUTO 
3 : 2 PULLDOWN 
Panasonic AUTO (4 : 3) OFF
NORMAL 
[ 
VIDEO ] 
VIDEO NR 
OFF Block NR
Mosquito NROFFOFFREFRESH RATE
100 Hz
3 : 2 PULLDOWN 
VIDEO NR 
SIGNAL 
OFF 
OFF 
H-FREQ.
V-FREQ.kHz
Hz33.8
60.0
Block NR
Mosquito NROFFOFFREFRESH RATE
100 Hz
[ 
Digital ] 
3 : 2 PULLDOWN 
VIDEO NR 
SIGNAL 
OFF 
OFF 
 [ 
COMPONENT ] 
Block NR
Mosquito NROFFOFFREFRESH RATE
100 Hz
SYNC 
VIDEO NR 
SIGNAL 
H-FREQ.
V-FREQ.kHz
Hz33.8
60.0
[ 
RGB ] 
3 : 2 PULLDOWN 
OFF 
Block NR
Mosquito NROFFOFFREFRESH RATE
100 HzOFF  AUTO 
1/2
PC
OFF
STANDBY SAVE
OFF
POWER MANAGEMENTOFF
AUTO POWER OFF
OFF
OSD LANGUAGEENGLISH (
US) COMPONENT/RGB-IN SELECT
RGB
INPUT LABELSIGNAL
POWER SAVE
SET UP
Press ACTION  (  ) button 
						

							44
3:2 PULLDOWN COLOR SYSTEM / Panasonic AUTO
Select SIGNAL from the “SET UP” menu during VIDEO (S VIDEO) input
signal mode.(“SIGNAL [VIDEO]” menu is displayed.)
SET UP for Input Signals
Press to select the “COLOR SYSTEM” or “Panasonic 
AUTO”.
Press to select each function.
If the image becomes unstable:
With the system set on Auto, under conditions of low 
level or noisy input signals the image may in rare 
cases become unstable. Should this occur, set the 
system to match the format of the input signal.
Press to select 3:2 
PULLDOWN.
Press to set ON/OFF.
Press to exit from adjust mode. 3:2 PULLDOWN: When ON, the display attempts to reproduce a more natural interpretation of sources such as movie 
pictures, which are recorded at 24 frames per second.
  If the picture is not stable, turn the setting to OFF.
Notes:
When ON, this setting only affects the following signal input:
•  NTSC / PAL signal input during “VIDEO (S VIDEO)” input signal.
•  525i(480i), 625i(575i), 1125(1080)/60i signal input during “COMPONENT” input signal.
1
2
Press ACTION  (  ) button
Mode Function
COLOR SYSTEM
Set the color system to match the input signal. When selecting “AUTO”, the color system is automatically 
selected from NTSC/PAL/SECAM, however, M.NTSC signal is not displayed properly depending on 
the attached terminal board. To display M.NTSC signal, select “M.NTSC” in COLOR SYSTEM.
AUTO SECAM M.NTSC NTSCPA L
Panasonic AUTO
(4 : 3 )Set to “NORMAL” to view 4:3 images in an unchanged format when Panasonic AUTO is selected. 
If you would like to view 4:3 images in Just format, set to “JUST”.
1/2
PC
OFF
STANDBY SAVE
OFF
POWER MANAGEMENTOFF
AUTO POWER OFF
OFF
OSD LANGUAGEENGLISH (
US) COMPONENT/RGB-IN SELECT
RGB
INPUT LABELSIGNAL
POWER SAVE
SET UP
3D Y/C FILTER (NTSC)
COLOR SYSTEM
SIGNAL
ON
AUTO
3 : 2 PULLDOWN
Panasonic AUTO (4 : 3)OFF
NORMAL
[ 
VIDEO ]
VIDEO NR
OFF
1/2
PC
OFF
STANDBY SAVE
OFF
POWER MANAGEMENTOFF
AUTO POWER OFF
OFF
OSD LANGUAGEENGLISH (
US) COMPONENT/RGB-IN SELECT
RGB
INPUT LABELSIGNAL
POWER SAVE
SET UP
3D Y/C FILTER (NTSC) 
COLOR SYSTEM 
SIGNAL 
ON 
AUTO 
3 : 2 PULLDOWN 
Panasonic AUTO (4 : 3) OFF 
NORMAL 
[ 
VIDEO ] 
VIDEO NR 
OFF 
SYNC 
VIDEO NR 
SIGNAL 
AUTO 
[ 
RGB ] 
3 : 2 PULLDOWN OFF 
OFF 
3 : 2 PULLDOWN
VIDEO NR
SIGNAL [ 
COMPONENT ]
OFF
OFF3 : 2 PULLDOWN
VIDEO NR
SIGNAL[ 
Digital ]
OFF
OFF
Press ACTION  (  ) button
Note: 
Panasonic AUTO does not function when BNC Dual Video Terminal Board (TY-FB9BD) is used. 
						

							45
SET UP for Input Signals
Select SIGNAL from the “SET UP” menu during RGB input signal.
Press to adjust.
Press to exit from adjust mode.
SYNC
Setting RGB sync signal
Confi rm that the input is set to RGB INPUT (this setting is valid only for RGB INPUT 
signal).
AUTO:  The H and V sync or synchronized signal are automatically selected. 
If both input, it is selected the H and V sync.
ON G:  Uses a synchronized signal on the Video G signal, which is input from 
the G connector.
VBS:  Uses a synchronized signal of Composite Sync input, which is input 
from the HD connector.
Displays the H (Horizontal) / V (Vertical) frequencies.
This display is valid only for RGB/PC and Digital input signal. 
Display range:
Horizontal  15 - 110 kHz
Vertical  48 - 120 Hz
H-FREQ. (kHz) / V-FREQ. (Hz)
1/2
PC
OFF
STANDBY SAVE
OFF
POWER MANAGEMENTOFF
AUTO POWER OFF
OFF
OSD LANGUAGEENGLISH (
US) COMPONENT/RGB-IN SELECT
RGB
INPUT LABELSIGNAL
POWER SAVE
SET UP
SYNC
VIDEO NR
SIGNAL
AUTO
[ 
RGB ]
3 : 2 PULLDOWNOFF
OFF
SYNC
AUTO
SYNC
ON G
SYNC
VBS
H-FREQ.
V-FREQ.kHz
Hz33.8
60.0
1
2
Press ACTION  (  ) button 
						

							46
1
2
3
5Press to display the Setup menu.
4
6
Item Effect Adjustments
Weekly 
Command 
TimerSets Weekly Command Timer. (see page 50)
Onscreen 
display
On Off
On:  Displays all the following on screen.
• Power on display
• Input signal switch display
• No signal display
• Mute and the remaining time of off-timer after 
 was pressed.
Off:  Hides all the items above from view.
Initial INPUTOff  PC  INPUT1  INPUT2  INPUT3 
Adjusts the input signal when the unit is turned on.
Notes:
• Only the adjusted signal is displayed. (see page 20)
• Signal can be displayed when the Terminal board is installed.
• This menu is available only when “INPUT lock” is “Off”.
• When a dual input terminal board is attached, A or B is displayed depending on the selected input 
signal. (Ex. INPUT1A, INPUT1B) 
Press to select “OSD Language”.
Press and hold until the Options menu is displayed.
Press to select your preferred menu.
Press to adjust the menu.
Press to exit from 
Options menu.
Options 
Weekly Command Timer 
Initial VOL level 
1/3 
 
Off  Off 
0  0 Maximum VOL level Off INPUT lock Off Button lock Off Remocon User level Off Advanced PIP 
Initial INPUT  Onscreen display On 
O f f 
Options Adjustments 
						

							47
Item Effect Adjustments
Initial VOL 
level
Off On
Press  button to adjust the volume when the unit is turned on.
Off  On
Off:  Sets normal volume.
On:  Sets your preferred volume.
Notes:
• 
When “Maximum VOL level” is “On”, the volume can only be adjusted between 0 and your maximum range.•  You can hear the changed volume regardless of your volume setting before opening the options menu 
if you adjust the volume when “Initial VOL level” is “On” and cursor is on the menu.
Maximum VOL 
level
Off On
Press  button to adjust the maximum volume.
Off  On
Off:  Sets auto maximum volume.
On:  Sets your preferred maximum volume.
Notes:
•  If the “Maximum VOL level” is set lower than the “Initial VOL level”, the “Initial VOL level” automatically 
becomes the same as the “Maximum VOL level”.
• The volume display can go up to 63 regardless of the settings.
• 
You can hear the changed volume regardless of your volume setting before opening the options menu if you 
adjust the volume when “Maximum VOL level” is “On” and cursor is on the menu.
INPUT lockOff  PC  INPUT1  INPUT2  INPUT3
Locks the input switch operation.
Notes:
• Only the adjusted signal is displayed (see page 20).
• Signal can be displayed when the Terminal board is installed.
• Input switch can be used when this is set to “Off”.
•  In two screen display mode, if anything other than “Off” is set, the value will be fi xed as the value input 
in the single screen display mode.
• When a dual input terminal board is attached, A or B is displayed depending on the selected input 
signal. (Ex. INPUT1A, INPUT1B) 
Button lockOff  MENU&ENTER  On 
Off:  All the buttons at the bottom of the main unit can be used.
MENU&ENTER: Locks 
MENU and ENTER/ buttons on bottom face of main unit.
On:  Locks all the button on bottom face of main unit.
Sets Button lock with the unit buttons in the following procedure.
Off:  Press 
 four times→Press INPUT four times→Press  four times→Press ENTER/MENU&ENTER: Press ENTER/ four times→Press  four times→Press INPUT four times→Press ENTER/On:  Press  four times→Press ENTER/ four times→Press  four times→Press ENTER/
Remocon 
User levelOff   User1   User2   User3 
Off:  You can use all of the buttons on the remote control.
User1: You can only use , , , , , , ,  buttons on the remote control.
User2:
 You can only use , , buttons on the remote control.
User3: Locks all the buttons on remote control.
Advanced PIP
Off On
Off:  Sets normal two screen display mode (see page 24).
On:  Sets Advanced PIP mode (see page 25).
Notes:
• When “INPUT lock” is “On”, you cannot use all the two screen display functions.
• 
,  buttons are unavailable during Advanced PIP mode operation.
Options 
On Weekly Command Timer Onscreen display Off Initial INPUT 
1/3 
 
Maximum VOL level  Initial VOL level 
Button lock 
INPUT lock 
Advanced PIP 
Remocon User level 
Off  Off 
0  0 
Off 
Off 
Off 
Off 
Options Adjustments 
						

							48
Item Effect Adjustments
Off-timer 
function
EnableDisable
Enable:  Enables the “Off-timer function”.
Disable:  Disables the “Off-timer function”.
Note:    When “Disable” is set, the Off-timer is cancelled.
Initial Power 
ModeNormal  Standby  On
Sets the power mode of the unit for when the power recovers from failure or after plugging off and in again.Normal:  Power returns in as the same state as before the power interruption.
Standby:  Power returns in standby mode. (Power Indicator : red/orange)
On:    Power returns in power On. (Power Indicator : green)
Note:  
When using multiple displays, “Standby” is preferred to be set in order to reduce a power load.
ID selectSets panel ID number when panel is used in “Remote ID” or “Serial ID”.
Set value range: 0 - 100
(Standard value: 0)
Remote ID
Off On
Off:  Disables ID remote control functions. You can use normal remote control operations.
On:  Enable ID remote control functions.
Serial ID
Off On
Sets the panel ID Control.
Off:  Disables external control by the ID.
On:  Enables the external control by the ID.
Display size
Off On
Adjusts the image display size on screen.
Off:  Sets the normal image display size on screen.
On:  Sets the image display size approximately 95 % of the normal image display.
    Off       On
  
Notes:
• This setting is valid only when the input signals are as follows; 
  NTSC, PAL, SECAM, M.NTSC, PAL60, PAL-M, PAL-N (BNC Dual Video Terminal Board (TY-FB9BD)) 
525i, 525p, 625i, 625p, 750/60p, 750/50p, 1125/60i, 1125/50i, 1125/24sF, 1125/25p, 1125/24p, 
1125/30p, 1125/60p·50p, 1250/50i (Component Video, RGB, DVI, SDI, HDMI)
• This setting is invalid when two screen display, digital zoom, Multi display or Portrait display is 
selected.
• When “Display size” is set to “On”, “H-POS” and “V-POS” in “POS. /SIZE” can be adjusted.
• Refer to each board’s operating instruction for DVI, SDI, HDMI’s corresponding signals.
Studio W/B
Off On
Off:  Nullify all the settings adjusted.
On:  Sets the color temperature for TV studio.
Note:  Valid only when the low is set as color temperature on screen adjustment.
Studio Gain
Off On
Sharpens the contrast for a better view when a part of the image is too light to see.
Off:  Disables “Studio Gain”.
On:  Enables “Studio Gain”.
Note:  This setting is valid only when the input signals are as follows:
    Component Video, RGB (analog), SDI, HDMI
Options
EnableOff-timer function
NormalInitial Power Mode0ID selectOffRemote IDOffSerial IDOffDisplay sizeOffStudio W/BOffStudio Gain
2/3
Options Adjustments 
						

							49
Item Effect Adjustments
Slot PowerOff  Auto  On 
Off:  Power is not transmitted to the slot power.
Auto:  Power is transmitted to the slot power only when main power is on.
On:  Power is transmitted to the slot power when main power is on or in the standby state.
Note:  In some cases, power is transmitted to the slot power when main power is on or in the standby 
state regardless of the slot power setting.
Power On 
Screen DelayOff   1   2   3....   30 
You can set the power-on delay time of the displays to reduce the power load, when you press 
 to 
turn on the multiple displays that are set together, for example, on MULTI DISPLAY system. 
Set each display’s setting individually.
Off:      The display will be turned on at the same time as 
 is pressed.1 to 30 (sec.):  Set the power-on delay time (second).
     After pressing , the display will be powered on with time delay depending on this setting.Notes:
• During this function is working, the power indicator is blinking green.
• This function also works when the power recovers from failure or after plugging off and in again the 
power cord.
  After you unplug and plug the power cord in while the unit is in standby mode and also the power is 
being supplied to a terminal board, the unit will start supplying the power to the board with time delay 
according to the setting.
  The power indicator lights up red fi rst and it turns orange when the power starts being supplied to the 
board.
V.Installation
Off On
Off:  Sets fan to the horizontal installation mode.
On:  Sets fan to the vertical installation mode.
Notes:
• This functions when display is turned on.
• Turn up the power switch for the upward direction when you set Display vertically.
Rotate
Off On
Off:  Does not rotate the image.
On:  Rotates the image 180 degrees.
Serial Slot 
SelectSlot1  Slot2   Slot3
Selects the slot which communicates serial.
Note: 
The setting of an external command can be set only from the fi xed serial terminal. (see page 12)
Normalization
When both main unit buttons and remote control are disabled due to the “Button lock”, “Remocon User level” or “Remote 
ID” adjustments, set all the values “Off” so that all the buttons are enabled again.
Press the 
 button on main unit together with  button on the remote control and hold for more than 5 seconds. The 
“SHIPPING” menu is displayed and the lock is released when it disappears.
3/3 Options 
O f f 
Off
Off V. lnstallation
Rotate
Slot1 Serial Slot Select Slot power Off
Power On Screen Delay
Options Adjustments 
						

							50
Options 
On Weekly Command TimerOnscreen display 
1/3 
 
Weekly Command Timer 
On Program1Function Monday 
Program3Tuesday --- Wednesday Program3Thursday --- Friday Program6Saturday Program4Sunday Program Edit 
Weekly Command Timer 
Program1On Monday Function 
Program3Tuesday 
--- Wednesday Program3Thursday --- Friday Program6Saturday Program4Sunday Program Edit 
Program3Thursday --- Friday Program6Saturday Program4Sunday Program Edit 
Weekly Command Timer 
8:00 
10:30 01
02
1/8
--:-- 03--:-- 04--:-- 
--:-- 0512:00 069:12 PON
IMS:SL1 
--- 
--- 
--- 
---  DAM:ZOOM 
AVL:10 0708
1Program
Program number
Options Adjustments
Weekly Command Timer
You can set 7-day timer programming by setting time and command.
Note: 
Before setting Weekly Command Timer, set PRESENT TIME SETUP.  (see page 31)
Press to select Function.
Press to select “On”.
Note:
•  When Function is set to On, SET UP TIMER 
(see page 32) is unavailable and INTERVAL 
/ TIME OF DAY in MODE of SCREENSAVER 
(see page 33) cannot be selected.
1
Press to select a day.
Press to select a program number.
Note:
• You can set the program from 1 to 7.
--- indicates unset.
2
Press to select Program Edit.
Press to show the Program Edit screen.
Press to select Program.
Press to change the program numbers (1-7).
4 3
Press ACTION  (  ) button
Program Edit screen