Panasonic Hd Plasma Display Th 50pf10 Operating Instructions

11
Connections
PC Input Terminals connection
Notes:
•  Due to space limitations, occasionally you may have trouble connecting Mini D-sub 15P cable with ferrite core to PC 
input Terminal.
•  Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical scanning 
frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.)
•  The display resolution is a maximum of 1,440 × 1,080 dots when the aspect mode...

12
Connections
SERIAL Terminals connection
Notes:
•  Use the RS-232C cable to connect the computer to the Plasma Display.
•  The computer shown is for example purposes only.
•  Additional equipment and cables shown are not supplied with this set.
The SERIAL terminal conforms to the RS-232C interface specifi cation, so that the Plasma Display can be controlled by a 
computer which is connected to this terminal.
The computer will require software which allows the sending and receiving of control data which...

13
SLOT3 
P R /C R /R P B /C B /B Y/G AUDIO R L COMPONENT/RGB IN 
AUDIO 
OUT  Y ,  P 
B ,    P R , 
OUT P
R 
P B 
Y 
L 
R 
COMPONEN T VIDEO OUT 
Connections
COMPONENT / RGB connection
Notes:
•  Change the “COMPONENT/RGB-IN SELECT” setting in the “SET UP” menu to “COMPONENT” 
  (when COMPONENT signal connection) or “RGB” (when RGB signal connection). (see page 42)
•  Additional equipment, cables and adapter plugs shown are not supplied with this set.
•  SYNC ON G signal is needed. (see page 45)RCA-BNC...

14
Power ON / OFF 
When the POWER is turned on for the fi rst 
time, the LANGUAGE selection screen is 
displayed.
From the second time on, language selection can 
be done from the setup menu. (see page 20)
Select the desired language using the   
or   
button and press the ACTION (  ) 
button.
Note: 
Set with the remote control. Buttons on the main 
unit are unavailable for this setting.From the second time on, the 
screen shown below is displayed 
for a while (setting condition is an 
example).
English...

15
Press the  button on the remote control to turn the Plasma Display off.
Power Indicator: Red (standby) 
Press the 
 button on the remote control to turn the Plasma Display on.
Power Indicator: Green
Turn the power to the Plasma Display off by pressing the 
   switch on the unit, 
when the Plasma Display is on or in standby mode.
Note: 
During operation of the power management function, the power indicator turns 
orange in the power off state.
Power ON / OFF 

INPUT MENU ENTER/+/ VOL-/
16
Basic Controls
MENU Screen ON / OFF
Each time the MENU button is pressed, the menu screen 
will switch. (see page 18)
INPUT button
(INPUT1, INPUT2, INPUT3 and PC selection)
(see page 20) Main Power On / Off Switch
Power Indicator
The Power Indicator will light.
• Power-OFF .... Indicator not illuminated (The unit will still 
consume some power as long as the power 
cord is still inserted into the wall outlet.)
• Standby  ......... Red
• Power-ON ...... Green
• DPMS...

17
Basic Controls
OFF  TIMER 90
1
2
3 PCNORMAL
Standby (ON / OFF) button
The Plasma Display must fi rst be plugged into 
the wall outlet and turned on at the power switch 
(see page 14).
Press ON to turn the Plasma Display On, from 
Standby mode. Press OFF to turn the Plasma 
Display Off to Standby mode.
SET UP button (see page 18, 19)
SOUND button (see page 28)
DIRECT INPUT buttons
Press the INPUT “1”, “2”, “3” or “PC” 
input mode selection button to select 
the INPUT mode. (see page 20)
This button is...

18
Normal Viewing PICTURE SETUP
SOUNDPOS. /SIZE
On-Screen Menu Displays
The MENU button on the unit can also be 
pressed.
Each time the MENU button is pressed, the 
menu screen will switch. To PICTURE adjust menu
(see page 26)
To ADVANCED  SETTINGS
(see page 26, 27)Press to select 
“ON”.
Press to enter 
ADVANCED 
SETTINGS.
1/2
PC
OFF
STANDBY SAVE
OFF
POWER MANAGEMENTOFF
AUTO POWER OFF
OFF
OSD LANGUAGEENGLISH (
US) COMPONENT/RGB-IN SELECT
RGB
INPUT LABELSIGNAL
POWER SAVE
SET UP
2/2 SET UP 
SCREENSAVER...

19
2  Press to access 
each adjust 
screen.
Press the R button to return 
to previous menu.
Press the R button to return to 
“SET UP” menu. Press to select 
POWER ON TIME / 
POWER OFF TIME.
Press to set up 
POWER ON TIME / 
POWER OFF TIME.
To PRESENT TIME SETUP.
(see page 31)
SYNC
VIDEO NR
SIGNAL
H-FREQ.
V-FREQ.kHz
Hz33.8
60.0
[ 
RGB ]
3 : 2 PULLDOWN
OFF
Block NR
Mosquito NROFFOFFREFRESH RATE100 HzOFF AUTO
3 : 2 PULLDOWN
VIDEO NR
SIGNAL [ 
COMPONENT ]
Block NR
Mosquito NROFFOFFREFRESH RATE
OFF
OFF
100...

20
Initial selections
Selecting the On-Screen Menu Language Selecting the input signal
Press to display the SET UP menu.
Press to select OSD LANGUAGE.
Press to select your preferred language.
   Selectable languages
1/2
PC
OFF
STANDBY SAVE
OFF
POWER MANAGEMENTOFF
AUTO POWER OFF
OFF
OSD LANGUAGEENGLISH (
US) COMPONENT/RGB-IN SELECT
RGB
INPUT LABELSIGNAL
POWER SAVE
SET UP
Select the input signals to be connected by installing the optional Terminal Boards.
Press to select the input signal to be played back...