Panasonic Hd Convertible Camera Aw He870n Operating Instructions

- 81 -
 Color Correction Set
B_Mg Gain [–127 to +127]
Increases or decreases the intermediate color between 
blue and magenta.
B_Mg Phase [–127 to +127]
Varies the hue of the intermediate color between blue 
and magenta.
Mg Gain [–127 to +127]
Increases or decreases the magenta.
Mg Phase [–127 to +127]
Varies the hue of the magenta.
Mg_R Gain [–127 to +127]
Increases or decreases the intermediate color between 
magenta and red.
Mg_R Phase [–127 to +127]
Varies the hue of the intermediate color between...

- 82 -
 G/L  Set
  Horizontal phase adjustment
[H Phase: –206 to +49]
Horizontal phase can be adjusted when a genlock signal 
is supplied.
  Subcarrier phase coarse adjustment
[SC Coarse: 0deg, 45deg, 90deg, 135deg, 
180deg, 225deg, 270deg, 315deg]
Coarse adjustment of subcarrier phase can be made 
when a genlock signal is supplied.
Valid for the composite and Y/C signals of the SD format.
  Subcarrier phase fine adjustment
[SC Fine: –127 to +127]
Fine adjustment of subcarrier phase can be made when...

- 83 -
  Flare correction level setting
[Flare R/G/B: 0
 to 100]
Flare correction level can be adjusted.
 Black stretch setting [Black Stretch: Off, On]
Black stretch to correct the suppression of black portions 
at low luminance can be set to OFF or ON.
 SD (480i) 2D LPF [SD 2D LPF: Off, Low, High]
This enables the cross color of the composite and Y/C 
signal output to be reduced by two levels.
The setting of this item has no effect on the HD (1080i or 
720p) format, RGB, Y/Pb/Pr or SDI signals.
...

- 84 -
  Component output setting
[Component:  RGB, Y/Pb/Pr, Y/C]
This enables RGB, Y/Pb/Pr or Y/C to be selected as 
the component signals which are to be output from the 
I/F REMOTE connector.
Y/C cannot be selected when “1080i” or “720p” has been 
selected as the “Video output format (Format)” setting.
If “1080i” or “720p” has been selected using the video 
output format selection function while Y/C is selected, the 
component output will be changed to Y/Pb/Pr.
(Refer to “Changing the component...

- 85 -
Menu item setting/changing (User Mode)
  Character output selection
[ Character Mix
Component: Off, On / Composite: Off, On / 
Option: Off, On]
This is used to select how the camera menu, status and 
other characters are to be output (Off or On).
Component:   How the characters to the component 
signals (RGB, Y/Pb/Pr) are output is 
selected.
Composite:   Character output method for composite 
signals and Y/C signals is selected.
Option:   How the characters to the optional card are 
output is...

- 86 -
Changing the settings
Changing the format settings
A confirmation screen appears when the format setting is to 
be changed on the Other Set screen.
1.  When the Format setting is changed on the Other Set 
screen and the ENTER/AWB switch is pressed, the 
“Format” sub menu screen such as the one shown below 
is displayed for about 10 seconds.
   Format
 Do you want to
 Set Format(1080i)?
  O.K.
  CANCEL
2.  If O.K. is selected and the ENTER/AWB switch is 
pressed within about 10 seconds after the...

- 87 -
Changing the component setting
A confirmation screen appears when the component setting 
is to be changed on the Other Set screen.
1.  When the Component setting is changed on the 
Other Set screen and the ENTER/AWB switch is 
pressed, the “Component” sub menu screen such as the 
one shown below is displayed for about 10 seconds.
   Component
 Do you want to
 Set Component(Y/Pb/Pr)?
  O.K.
  CANCEL
2.  If O.K. is selected and the ENTER/AWB switch is 
pressed within about 10 seconds after the...

- 88 -
Setting the EBU matrix
A confirmation screen appears when the EBU matrix is to be 
set on the Other Set screen.
1.  When the EBU matrix setting is changed on the 
Other Set screen and the ENTER/AWB switch is 
pressed, the “EBU Matrix” sub menu screen such as the 
one shown below is displayed for about 10 seconds.
   EBU Matrix
 Do you want to
 Set EBU Matrix(On)?
  O.K.
  CANCEL
2.  If O.K. is selected and the ENTER/AWB switch is 
pressed within about 10 seconds after the “EBU Matrix” 
sub menu...

- 89 -
Setting to initial set (Factory presets)
Setting to initial set
In case of the wrong setting in any use mode, take the 
following steps to return to the initial settings.
When initialization is performed, all of the camera menu’s 
setting values except for Format and Component will return 
to factory presets.
1.  Select “Initialize Data” on the main menu screen of each 
Use Mode.
Press the ENTER/AWB switch, then “Initialize Data” 
screen below is displayed for about 10 seconds.
   Initialize...

- 90 -
Setting to initial set (Factory presets)
Initial settings of the setting items (Factory preset values)
 Halogen, Fluorescent, Outdoor Mode
ItemHalogen Fluorescent Outdoor
Brightness Set Picture Level 000
Light PEAK/AVG 000
Light Area Top Cut Top Cut Top Cut
Shutter Mode StepStep ELC
  Step/Synchro OffOff ---
Gain 0dB0dBAuto
  AGC Max Gain ------18dB
Pedestal 00–40
Color Set Chroma Level 000
Flesh Tone 000
White Bal AWB A AWB A ATW
  ATW Speed ------Mid
Sharpness(DTL) Set DTL Select Sharpness...