Panasonic Hc X920 Owners Manual

							- 141 -
≥Please refer to the operating instruction of the device in use for details about the setting  of the 
wireless access point or smartphone.
If the Wi-Fi connection cannot be established
ProblemCheck points
It cannot connect to the 
wireless access point.
The wireless access point 
is not detected.
(General)
≥ Turn ON the wireless access point.
≥ Approach the wireless access point and reconnect.
≥ If it takes time to complete the connection, the Wi-Fi 
connection will be aborted.
Reset the connection settings.
≥ Check how to connect to the wireless access point and how 
to set the security settings.
≥ Make sure the wireless access point is registered in this unit. 
(l 155 )
≥ The device may be unable to locate the wireless access point 
due to problems with the signal. Use [Manual Connection]. 
(l 136 )
(Easy Connection)
≥ Make sure the wireless access point is in the correct WPS 
standby mode.
≥ Make sure the PIN code has been correctly input.
(Manual Connection)
≥ Make sure the SSID and Password have been correctly input.
≥ Check the Authentication method, Encryption type, and 
Encryption key (Password).
Radio waves of the 
wireless access point get 
disconnected.
≥ The condition may improved by moving the location or 
changing the angle of the wireless access point.
≥ If you use another 2.4 GHz band device such as a microwave 
oven or cordless telephone nearby, you may interrupt the 
signal. Keep a sufficient distance from these types of devices.
The Wi-Fi connection is 
not possible between this 
unit and a smartphone.
(Wireless Access Point Connection)
≥ Make sure the smartphone is properly connected to the 
wireless access point by checking the Wi-Fi settings of the 
smartphone.
≥ Make sure this unit and the smartphone are connected to the 
same wireless access point.
≥ Make sure the wireless access point is registered in this unit. 
(l 155 )
(Direct Connection)
≥ Make sure the smartphone is properly connected to this unit 
by checking the Wi-Fi settings of the smartphone.
≥ Make sure the SSID and Password have been correctly input.
≥ Make sure the smartphone is not connected to the wireless 
access point. If it is connected to the wireless access point, 
change the Wi-Fi access point using the smartphones Wi-Fi 
set up. 
						

							- 142 -
It takes long time every 
time to connect to a 
smartphone.≥It may take longer time to connect depending on the Wi-Fi 
connection setting of the smartphone, but it is not a 
malfunction.
This unit is not displayed 
in the Wi-Fi setting screen 
of the smartphone.
≥ Try switching the ON/OFF of the Wi-Fi function in the Wi-Fi 
settings of the smartphone.
The Wi-Fi connection is 
disconnected immediately.
≥ If there is a setting for avoiding poor connections in the Wi-Fi 
setting menu of the Android device 4.0 or later version, turn it 
OFF.
ProblemCheck points 
						

							- 143 -
Using a smartphone, you can perform record/playback operations from a remote location or upload 
motion pictures and still pictures recorded in this unit on SNS (Social Networking Service).
AWhen connecting to a smartphone
B When connecting to a wireless access point
≥Refer to [Help] in the “Image App” menu for further details on how to operate.
Proceed to Step 2 when your Wi-Fi connection has been made via [Direct Connection] in [Wi-Fi 
Setup]  ( l139 ).
1Press Wi-Fi button and touch [Link to Cell]. ≥It will go into connection standby for remote operation.
≥ Even if the Wi-Fi button is pressed continuously for approximately 2 seconds while Wi-Fi is not in 
use, it will go into connection standby for remote operation.
(This will operate even when the power of this unit is turned off excluding when the power of this 
unit is turned off by pressing the power button)
2Start up the smartphone application “Image App”.≥When the connection is complete, images of this unit is displayed on the smartphone screen.
To exit remote operations:Touch [EXIT] or press Wi-Fi button.
≥The message is displayed. Touch [YES] to close the indication.
Wi-Fi [HC-X920]/[HC-X920M]
Recording/playing back with Link to 
Cell operations
≥Before using, perform the preparations for using the Wi-Fi function. ( l129 )
≥ You need to turn on the Wi-Fi function of your smartphone and install “Image App”. 
(l 132 ) 
≥ Do not remove the SD card during remote operations.
Using with a direct connection
Image AppImage App
Image App

 
						

							- 144 -
1Connect the smartphone and the wireless access point.
2Press Wi-Fi button and touch [Link to Cell]. ≥It will go into connection standby for remote operation.
≥ Even if the Wi-Fi button is pressed continuously for approximately 2 seconds while Wi-Fi is not in 
use, it will go into connection standby for remote operation.
(This will operate even when the power of this unit is turned off excluding when the power of this 
unit is turned off by pressing the power button)
3Start up the smartphone application “Image App”.≥When the connection is complete, images of this unit is displayed on the smartphone screen.
To exit remote operations:Touch [EXIT] or press Wi-Fi button.
≥The message is displayed. Touch [YES] to close the indication.
Using with a wireless access point connection 
						

							- 145 -
Smartphone screen shots are example displayed in Motion Picture Recording Mode and Playback 
Mode.
* The screen differs depending on the operating system.
Screen display during remote operations
Recording screen1 Remaining battery power of this unit
2 Zoom
3 Photoshot button
4 Menu display
5 Playback mode button
6 Recording mode button
7 Recording start/stop button
8 Motion Picture Recording Mode/Still Picture 
Recording Mode toggle button
9 Name of the connected device
Playback screen
1 Number of scenes
2 Camera function button
3 Menu display
4 Playback mode button
5 Recording mode button
6 Scene information display
7 Name of the connected device
XXXXXXXXX



\b


XXXXXXXXX
1/16
AVCHD_0001 2013/12/15 15:30:50



\b 
						

							- 146 -
∫
When Recording Mode
≥Turning the unit off
≥ Selecting a mode
≥ Recording motion pictures/still pictures
≥ Selecting a media to record
≥ Using the zoom (Available in the medium or fast speed)
≥ Selecting a iA/MNL mode
≥ White Balance
≥ Recording format
≥ Backlight Compensation
≥ Picture Size
≥ Aspect Ratio
≥ Self-timer
∫ When Playback Mode
≥Playback
jScenes recorded in iFrame cannot be played back. 
j 3D still pictures are played back in 2D.
≥ Selecting a media to playback (SD card/Built-in memory)
≥ Switching the media (AVCHD/MP4/still picture)
≥ Delete
≥ Save (Copy)
jScenes recorded in AVCHD cannot be copied. 
j Scenes recorded in iFrame can only be copied with iOS devices.
j 3D still pictures (MPO format) will be copied as 2D still pictures (JPEG).
≥ Smart Home Network
jIt is possible to post to SNS service or perform playback operation when this unit is connected 
to the DLNA-compatible TV via wireless access point using a smartphone.
≥ Creating and saving scenes with Highlight Playback 
(Highlight Playback cannot be used for iFrame or MP4 scenes)
≥If you close the LCD monitor face down while recording, the LCD monitor of this unit will not 
display.
≥ Be sure to pay special attention to the privacy, the likeness rights, etc. of the subject when 
you use this function. Use at your own risk.
Functions available for remote operations
HC-X920M
HC-X920M 
						

							- 147 -
Connecting this unit to a DLNA-compatible device via Wi-Fi, you can play back scenes and still 
pictures on the device.
ADLNA-compatible TV
1Press Wi-Fi button. 
2To u c h  [DLNA Play].≥If you touch [Change AP], you can switch the wireless access point to another one that has been 
registered to this unit.
≥ If you touch [CANCEL], the Wi-Fi connection is canceled.
≥ When the connection is complete, the screen of this unit turns off. To display it again, touch the 
screen.
3Select this unit (SSID) by the TV side.≥Select the media (SD/MEM) and select the motion picture (AVCHD) or still picture (JPEG) to 
playback.
4Perform playback operations with the TV 
remote control.
≥Playback operations may differ depending on the TV in use.
≥ The following operations can be performed if a color button is 
pushed.
Blue/Red: Skip playback
≥ Fast forward/Fast rewind playback cannot be performed.
≥ You cannot perform playback operations with this unit.
To exit the playback on the TV:Touch [EXIT] or press Wi-Fi button.
A message is displayed. Touch [YES] to exit.
≥The images recorded in 3D are played back as 2D.
≥ Scenes recorded in iFrame/MP4 cannot be played back.
≥ Depending on the TV used, it may not playback in AVCHD picture quality even when the scene 
recorded in AVCHD is played back.
Wi-Fi [HC-X920]/[HC-X920M]
DLNA Play
≥Before using, perform the preparations for using the Wi-Fi function. ( l130 )
≥ Please read the operating instructions for the TV about connecting TV to the wireless 
access point.
≥ Do not remove the SD card while playing back on a TV.

(Examples of operations during 
motion picture playback)
A Skip playback
B Sto p
C Playback/Pause

 
						

							- 148 -
You can broadcast motion pictures of this unit live by setting up a link between the “LUMIX CLUB” 
and USTREAM.
1Press Wi-Fi button. 
2Touch [Live Cast].≥If a “LUMIX CLUB” Login ID and Password has not been registered to this unit yet, enter them 
according to the screen.
≥ If you touch [Change AP], you can switch the wireless access point to another one that has been 
registered to this unit.
≥ When the connection is made correctly, the screen of this unit switches to the Live Cast Mode.
∫ To send e-mails
You can send e-mails containing such information as the USTREAM channel name or the 
scheduled broadcast date.
≥This unit can only set the scheduled broadcast date. ( l150 ) For other settings, set them on the 
“LUMIX CLUB”.
≥ On the “LUMIX CLUB”, register the destination addresses of the e-mail in advance.
Wi-Fi [HC-X920]/[HC-X920M]
Live Cast
≥Before using, perform the preparations for using the Wi-Fi function. ( l130 )
≥ Check your contract details carefully, as smartphone and internet contract details may 
result in high communication charges being incurred, or a limit placed on 
communication traffic.
USTREAM
LUMIX CLUB
XXXXXXXXX 
						

							- 149 -
Touch .≥/ /  will disappear when no touch function is 
performed for a specific period of time. To display them again, 
touch the screen.
∫ To start the live broadcast
Touch .≥If you press the start recording button, you can simultaneously 
record the broadcast to this unit.
≥ / /  will disappear when no touch function is 
performed for a specific period of time. To display them again, 
touch the screen.
∫ To stop the live broadcast
Touch .
≥When   (gray) is displayed, unsent data is present. 
Wait until the unsent data is sent and   is displayed.
To exit the Live Cast Mode:Touch [EXIT] or press Wi-Fi button.
≥A message is displayed. Touch [YES] to exit.
∫ About the screen indications in the Live Cast Mode
≥Recording is performed in Intelligent Auto Mode.
≥ If you close the LCD monitor face down while recording, the LCD monitor of this unit will not 
display.
≥ Image content may be leaked to third parties depending on the USTREAM image publication 
method settings. Set the publication range and Password using USTREAM if required.
≥ Be sure to pay special attention to the privacy, the likeness rights, etc. of the subject when 
you use this function. Use at your own risk.
R 1h20m R 1h20m
R 1h20m
A [EXIT]
/ Live Broadcast indication
Image quality (l 150)
1h23m Elapsed time of the live broadcast
12fps Frame rate ( l150 )
Number of people watching the live 
broadcast
≥ Up to 9999 viewers can be 
indicated. The indication does not 
appear when the number is 0.
E-mail delivery setting

R 1h20mR 1h20mR 1h20m
A [EXIT] 
						

							- 150 -
Touch   to display the live broadcast setting 
screen.
≥/ /  will disappear when no touch function is 
performed for a specific period of time. To display them again, 
touch the screen.
∫ To configure the e-mail delivery settings
You can make the delivery setting of a broadcast notification e-mail and the setting for the 
scheduled time and date of the broadcast indicated in the e-mail.
1 Touch [E-MAIL SETUP].
2 Touch [ON] or [OFF].
3 (When [ON] is selected)
To set the scheduled broadcast date.
∫To set the image quality
1 Touch [IMAGE QUALITY].
2 Touch the desired image quality.
≥If the selected image quality has an image quality higher than the one you are using, images will 
appear as if the frame rate is low.
Configuring the live broadcast settings
R 1h20m R 1h20m
R 1h20m
A [EXIT]
[ON]:Enables e-mailing.
[OFF]:Disables e-mailing.
[AUTO]:Allows you to set to the time and date you have touched  .
[MANUAL]:Allows you to set the desired time and date.
≥The setting method is the same as [CLOCK SET]. ( l19)
Image qualityPicture sizeFrame rateScreen indications
[High] 1280k720 5 to 30 fps
[Medium] 640k360 5 to 30 fps
[Low] 320k176 5 to 30 fps
[AUTO] Use this option to check the image quality and automatically set the 
item.