Panasonic Full HD LCD Display TH 70LF50 Operating Instructions

3D Y/C FILTER
ON
1/2
SIGNAL
INPUT LABEL
ECO MODE SETTINGS
WOBBLING
SET UP
OFF
COMPONENT/RGB-IN SELECT
RGB SCREENSAVER
NO ACTIVITY POWER OFF
DISABLE
OSD LANGUAGEENGLISH (
US)
3D Y/C FILTER
COLOR SYSTEM
SIGNAL
ON
AUTO
3 : 2 PULLDOWN
OFF
[ 
VIDEO ]
NOISE REDUCTION
OFF
3 : 2 PULLDOWN
SIGNAL
OFF
[ 
Digital ]
NOISE REDUCTION
OFFHDMI RANGE
AUTOH-FREQ.
V- F R E Q .kHz
Hz 63.98
60.02
SIGNAL FORMAT 1280×1024/60
DOT CLOCK FREQ.MHz 108.0
SIGNAL [ 
COMPONENT ]
XGA MODENOISE REDUCTION
OFFH-FREQ.
V- F R E Q .kHz
Hz...

3D Y/C FILTER
COLOR SYSTEM 
SIGNAL 
ON 
AUTO 
3 : 2 PULLDOWN OFF 
[ 
VIDEO ] 
3 : 2 PULLDOWN OFF 
XGA MODE
1024×768
42
3:2 PULLDOWN
COLOR SYSTEM
Select SIGNAL from the “SET UP” menu during Video input signal mode. 
(“SIGNAL [VIDEO]” menu is displayed.)
SET UP for Input Signals
Press to select the “COLOR SYSTEM” .
Press to select each function.
If the image becomes unstable:
With the system set on Auto, under conditions of low level or noisy 
input signals the image may in rare cases become unstable....

()NOISE REDUCTION
OFF 
3 : 2 PULLDOWN
SIGNAL
OFF
[ 
Digital ]
NOISE REDUCTION
OFFHDMI RANGE
AUTO
43
Note: 
NOISE REDUCTION can be adjusted while a Video or Component signal is being applied.
SET UP for Input Signals
NOISE REDUCTION
Press to select “NOISE REDUCTION”.
Press to select “OFF”, “AUTO”, “MIN”, “MID”, “MAX”.
AUTO:  NOISE REDUCTION will be automatically 
selected from “MIN”, “MID” or “MAX”.
SYNC
SIGNAL[ 
RGB ]
3 : 2 PULLDOWN
XGA MODEAUTO
OFF
1024
×768
This function operates only during input from...

H-FREQ.
V- F R E Q .kHz
Hz 63.98
60.02
SIGNAL FORMAT 1280×1024/60
H-FREQ.
V-FREQ.kHz
Hz 63.98
60.02
DOT CLOCK FREQ.MHz 108.0
SIGNAL FORMAT 1280×1024/60
44
SET UP for Input Signals
Displays the frequency and the type of the current input signal.
This display is valid only for COMPONENT/RGB/PC and Digital input signal. 
Display range:
Horizontal  30 - 110 kHz
Vertical  48 - 120 Hz
The dot clock frequency is displayed during digital signal input.
Note:
The automatically detected signal format may be...

2/2SET UP
MULTI DISPLAY SETUP
SET UP TIMER
PRESENT TIME SETUPNETWORK SETUPMENU DISPLAY DURATION15 SMENU TRANSPARENCY20
--:--:--:--:--:--
DHCP
NETWORK SETUP
SAVE
0
192.168.    0.    8
255.255.255.    0
192.168.    0.    1
1024
AUTO
RS-232COFF
SUBNET MASK
LAN SPEED GATEWAY IP ADDRESS
PORT
CONTROL I/F SELECT NETWORK ID
MAC ADDRESS
Network Setup
Make the various settings to use the network function.
  
DHCP, IP ADDRESS, SUBNET MASK, and GATEWAY settings
1 Set DHCP.
     When “OFF” is selected, IP ADDRESS and...

Options
1/3
Initial input On screen display
Input SearchOn
Off
Off Off
0 0Maximum VOL level Initial VOL levelOffInput lockOffButton lockOffRemocon User level
Options 
Enable Off-timer function Normal Initial Power Mode 0 ID select Off Remote ID Off Serial ID ---Serial Daisy ChainOff Studio W/B 
2/3 
 
3/3Options
Off
Off
Clock DisplaySlot powerOff
Power ON Screen Delay
Function button assign 1
Power On Message (No activity power off)On
Signal
Function button assign 2ScreensaverPower Switch LockOff
46
Item...

47
Item Adjustments
Button lockOff 
 On  MENU&ENTER 
Off:  All the buttons on main unit can be used.
MENU&ENTER: Locks 
MENU and  buttons on main unit.
On:  Locks all the button on main unit except the Power switch.
Sets Button lock with the unit buttons in the following procedure.
Off:  Press 
+/ four times
Press INPUT four times
Press -/ four times
Press MENU&ENTER: Press  four times
Press +/ four times
Press INPUT four times
Press On:  Press -/ four times
Press  four times
Press +/ four times
Press...

48
Normalization
When both main unit buttons and remote control are disabled due to the “Button lock”, “Remocon User level” or “Remote 
ID” adjustments, set all the values “Off” so that all the buttons are enabled again.
Press the 
-/ button on main unit together with  button on the remote control and hold for more than 5 seconds. 
The “Shipping” menu is displayed and the lock is released when it disappears.
Options Adjustments
Item Adjustments
Power On Message 
(No activity power 
off)Whether to...

49
Using Network Function
This unit has a network function to control the network connected display with your computer.
Note:
To use the network function, set each “NETWORK SETUP” setting and make sure to set the “CONTROL I/F SELECT” 
to “LAN”. (see page 45)
When “LAN” is set, power indicator lights orange under the condition of power off with remote control (stand-by state).
Example of Network Connection
Command Control
Display (main unit, rear)
Hub or broadband routerLAN cable
(not supplied)
Notes:
•...

50
Using Network Function
PJLink™ Protocol
The network function of the unit conforms with PJLink™ class 1 and you can operate the following actions from your 
computer using PJLink™ protocol. 
• Display setup
•  Display status query
Supported commands
Commands to control the unit with PJLink™ protocol are shown in the table below.
PJLink™ security authentication
Set “Panasonic” for the PJLink™ password.
•  PJLink™ is a pending trademark in Japan, the United States, and other countries or areas. 
Command...