Panasonic Electronic Board UB-5838C, UB-5338C Operating Instructions

For Your Safety11
Before You Start
This appliance is supplied with a moulded three pin 
mains plug for your safety and convenience.
A 5 amp. fuse is fitted in this plug. Should the fuse need 
to be replaced please ensure that the replacement fuse 
has a rating of 5 amps. and that it is approved by ASTA 
or BSI to BS1362. Check for the ASTA mark   or the 
BSI mark   on the body of the fuse. If the plug 
contains a removable fuse cover, you must ensure that 
it is refitted when the fuse is replaced. If you...

12
Precautions
Installation•Do not install the unit where it may be exposed to direct sunlight, near heating equipment, 
or near air-conditioning vents as this may cause discoloration of the screen.
• Do not install the unit in strong sunlight or strong lighting. Proper copying may become 
impossible.
• Do not install the unit in locations where the temperature may drop below 10°C (50°F) or 
may change suddenly as this may disable the unit’s ability to make copies.
Screen Film •Make thick and dark lines...

Precautions13
Before You StartBattery If a battery is used improperly, the battery may leak, causing corrosion of the unit, or it may 
burst. To prevent this, always follow the precautions given below.
•Always insert battery with its polarity properly oriented.
• If the battery has run out, remove it immediately and dispose of it according to local 
regulations.
Leaving drained battery may result in leakage.
• Do not disassemble battery or place it in a fire.
• Do not short battery.
Please take the...

14
Part Names and Functions
OFF
ON
Screen Film
Frame
Tr ay
Stand
Caster
Caster
with Lock
Scanner
Control Box Stand
Control Panel
Power Cord Battery Holder
AC Inlet Power Switch
SD Memory Card CoverSD Memory 
Card Slot USB Connector-A 
for USB Flash 
Memory Device
Caster with Lock
Caster
USB Connector-B 
for Computer
USB Connector-A 
for Printer
Fall-prevention
Extension Leg
Fall-prevention 
Extension Leg
UB5838C-PJQXC0259ZA_mst.book  14 ページ  ２００９年５月２６日　火曜日　午後２時５９分 

Part Names and Functions15
Before You Start
Control Panel
NameDescription
Display
When in standby mode, the display shows the current status of the unit as follows:
•The time is shown on the top left corner of the display.
• The scanning mode is shown on the icons on the left side of the display.
• The destination for scanned images is shown in the center of the display.
Mode Key
Press repeatedly to select the scanning mode. The selected mode will be indicated 
next to the icons on the left side of the...

16
Before Using
This unit has the following functions concerning 
information security. Please use them properly.
■Operation Password function
It is possible to set a password in order to prevent a 
third party from operating the electronic board when the 
power turns on or after a certain period of time has 
passed.
For information on setting the password, refer to page 
27.
The following display appears in the password input 
display. Press the Mode Key ( ), the Set-up Key 
( ) or the Advance Key ( )...

17
Using
Scanning
It is possible to output scanned images to a USB flash 
memory device, SD memory card, external printer, or 
computer.
If multiple output devices are connected to this unit at 
the same time, the output destination will be selected in 
the following priority:1. Computer
2. USB flash memory device
3. SD memory card
4. External printer
The current destination is shown on the display.
Note
• Do not install the unit in places subject to direct 
sunlight or strong lighting. Scanned images...

Scanning
18
1
Set the power switch to on (  I ).
2
Connect the USB flash memory device to “USB 
Connector-A for USB Flash Memory Device”.
• When the USB flash memory device is 
connected, a USB flash memory icon will blink 
on the display. Once the unit recognizes the 
device, the icon will stop blinking.
The display below is an example of the unit in 
standby mode.
Note
• You cannot use a USB flash memory device 
that is equipped with certain features such as 
a security feature.
3
Press the Mode Key...

Scanning19
Using
1
Set the power switch to on (  I ).
2
Open the SD memory card cover and insert the 
SD memory card into the SD memory card slot 
until it is locked. Then close the SD memory 
card cover.
• The SD memory card icon is shown on the 
display.
The display below is an example of the unit in 
standby mode.
Note
• SDHC memory card is not supported.
• If an SD memory card has been formatted 
(ex. by the general formatting software of a 
computer), it oftentimes cannot be recognized 
by this...

Scanning
20
6
Press the Mode Key ( ).
• The Screen Erase Announce is shown on the 
display.
7
After erasing the written text/diagrams on the 
screen, press the Mode Key ( ) to return to 
standby mode.
•Only remove the SD memory card once you 
have returned to standby mode.
• To remove the SD memory card, open the SD 
memory card cover and unlock the SD 
memory card by pressing it once. Once it is 
unlocked you may remove it.
• For information on saving files on an SD 
memory card, refer to page 17.
1
Set...