Panasonic Electronic Board Ub 5838 Operating Instructions

							Wall-Mounting Construction51
Installation
■Wall Types and Installation Procedures
The method for attaching the wall-mounting fixtures to the wall will vary depending on the nature of the wall’s 
structure.
Three available options are listed below.
Other methods may be necessary depending on the wall.
● Metal or Concrete walls
Stud plugs (sold in stores) are needed.
Drill eight holes in the wall.
For the correct hole size, refer to the instructions for 
the particular stud plugs used.
Insert the bolt through a hole in the wall-mounting 
fixture and tighten until the wall-mounting fixture is 
securely fixed to the wall.
Drill bit
Metal or concrete wall
Stud plug Insert a stud plug in each hole.
Wall-mounting fixture Bolt
UB5838C-PJQXC0259ZA_mst.book  51 ページ  ２００９年５月２６日　火曜日　午後２時５９分 
						

							Wall-Mounting Construction
52
● Plasterboard walls
Split-wing toggles (sold in stores) are needed.
●Wooden walls
Wood screws (sold in stores) are needed.
Insert the bolt through the hole in the wall-mounting 
fixture and attach the split-wing toggle. Then insert 
the split-wing toggle into the hole while the arms are 
horizontal.
For the correct hole size, refer to the instructions for 
the particular split-wing toggles used.
After the arms expand, pull the wall-mounting fixture 
out until the arms of the split-wing toggle grip firmly 
into the wall.
Tighten the bolt until the wall-mounting fixture is 
securely fixed to the wall.
Plasterboard
Split-wing toggle
Wall-mounting 
fixture
Bolt
Arms Arms
Insert the wood screw through the hole in the wall-
mounting fixture and tighten until the wall-mounting 
fixture is securely fixed to the wall.
For the correct hole size, refer to the instructions for 
the particular wood screws used.
Wall-mounting fixture
Wood screw
Wooden wall
UB5838C-PJQXC0259ZA_mst.book  52 ページ  ２００９年５月２６日　火曜日　午後２時５９分 
						

							53
Installation
Optional Stand Assembly (UE-608035)
■Included Parts
Check that the following parts are included with the optional stand (UE-608035).
*1Use four screws and rivets when installing the electronic board.*2The included wrench is necessary for tightening and loosening the screws, so keep it in a safe location.
Note
•Before assembly, be sure to lock the casters.
No.Part nameIllustrationQ’ty
Stand Base 2
Support Beam 2
Fall-prevention Extension Leg 4
Flat Head Screw (M6  × 60 mm [2
3/8]) 4
Nut 4
Wrench (4 mm [
5/32 ])*21
Support Bracket 2
Spring Washer 4
Screw (M6 ×  45 mm [1
25/32]) 4
Washer Not use with this electronic board
(This is used for other models.) 4
Screw (M6 ×  60 mm [2
3/8])*14
Rivet*
14
Wrench (5 mm [
13/64 ])*21
Locking the casters
(Push this side)
UB5838C-PJQXC0259ZA_mst.book  53 ページ  ２００９年５月２６日　火曜日　午後２時５９分 
						

							Optional Stand Assembly (UE-608035)
54
■ Assembly Instructions
1
Assemble the fall-prevention extension legs.
2
Assembling the stand
Locking casters side (rear)
UB5838C-PJQXC0259ZA_mst.book  54 ページ  ２００９年５月２６日　火曜日　午後２時５９分 
						

							Optional Stand Assembly (UE-608035)55
Installation
3
Pull the fall-prevention extension legs down.
Note
•When folding back the fall-prevention extension legs, release the lock as follows ( 1, 2).
4
Mount the unit.
•Refer to “Assembling the unit” (page 40).
2
1
1
1
2
UB5838C-PJQXC0259ZA_mst.book  55 ページ  ２００９年５月２６日　火曜日　午後２時５９分 
						

							Information for Users on Collection and Disposal of Old Equipment and used Batteries
These symbols on the products, packaging, and/or accompanying documents mean that used electrical and 
electronic products and batteries should not be mixed with general household waste.
For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable 
collection points, in accordance with your national legislation and the Directives 2002/96/EC and 2006/66/EC.
By disposing of these products and batteries correctly, you will help to save valuable resources and prevent any 
potential negative effects on human health and the environment which could otherwise arise from inappropriate 
waste handling.
For more information about collection and recycling of old products and batteries, please contact your local 
municipality, your waste disposal service or the point of sale where you purchased the items.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.
For business users in the European Union
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further 
information.
Information on Disposal in other Countries outside the European Union
These symbols are only valid in the European Union. If you wish to discard these items, please contact your 
local authorities or dealer and ask for the correct method of disposal.
Note for the battery symbol (bottom two symbol examples):
This symbol might be used in combination with a chemical symbol. In this case it complies with the requirement 
set by the Directive for the chemical involved.
Panasonic Communications Company of North America
Unit of Panasonic Corporation of North America
One Panasonic Way, Secaucus, New Jersey 07094
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario, L4W 2T3
Panasonic Business Systems U.K.
A Division of Panasonic U.K. Ltd.
Willoughby Road, Bracknell, Berkshire, RG12 8FP
Panasonic Marketing Europe GmbH
Hagenauer Strasse 43
65203 Wiesbaden, Germany For information of Compliance with EU relevant Regulatory
Directives, Contact to Authorised Representative:
Panasonic Testing Centre
Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, Germany
Web Site:   http://panasonic.net/
© Panasonic Communications Co., Ltd. 2009
PJQXC0259ZA  F0509E0
(For EU only)
UB5838C-PJQXC0259ZA_mst.book  56 ページ  ２００９年５月２６日　火曜日　午後２時５９分