Panasonic Electronic Board Ub 5838 Operating Instructions

							Assembling the unit41
Installation
■Assembly
1
Assemble the wall-mounting fixture or optional stand.
•If you are using a wall-mounting fixture, refer to “Wall-Mounting Construction” on page 48.
• If you are using a stand, refer to “Optional Stand Assembly (UE-608035)” on page 53.
2
Remove the joints and the shipping box.
•UB-5838C has 12 joints.
• UB-5338C has 8 joints.
* This is a diagram of the UB-5338C. UB-5838C has cushioning materials on the upper and lower sides of the center of the unit.
Note
• When handling the screen unit, grasp the side cover on either side of screen. Do not grasp the screen film 
surface, as this may scratch it.
• When removing the shipping box, make sure that it does not strike the screen unit. (The screen unit may 
fall over.)
• The shipping box, cushioning material, and other packing material will be necessary for repackaging this 
unit. Do not throw them away.
• Remove the screen fixing tapes from top down slowly not to damage it.
Power cord
Eraser Wall-mounting fixture
Operating Instructions
Markers
Washer, Clamp
Screen unit
Packing 
material USB cable
UB5838C-PJQXC0259ZA_mst.book  41 ページ  ２００９年５月２６日　火曜日　午後２時５９分 
						

							Assembling the unit
42
3
Collapse the carton box.
4
Remove the protective plastic bag and lay down 
the unit onto the shipping box with the screen 
film surface facing downward.
Note
• Make sure that the cushioning material and 
other packing materials do not strike the 
screen film. (Contact may damage the screen 
film.)
• When using the stand, advance to step 10.
[Wall-mounting]
5
Remove the four rivets.
Note
•To remove the rivets, turn them 
counterclockwise with a screwdriver. (The 
fixed part of the rivets will be raised.)
6
Hang the two wall-mounting shafts of the unit to 
the wall-mounting fixtures.
Note
•Ensure that the shafts fall into the groove of 
the wall-mounting fixture. 
If the shafts do not fit to the groove, adjust the 
position of the wall-mounting fixture.
Rivet
UB5838C-PJQXC0259ZA_mst.book  42 ページ  ２００９年５月２６日　火曜日　午後２時５９分 
						

							Assembling the unit43
Installation
7
After unscrew the 4 screws from the lower 
center frame cover, remove it.
8
Fasten the wall-mounting clasps of the unit 
securely to the wall with the 4 appropriate wall-
mounting hardware.
Note
•The 4 wall-mounting hardware are not 
included with the electronic board. Please 
purchase M6-size screws appropriate for your 
wall.
9
Attach the lower frame cover removed in step 7.
• Advance to “Electronic Board Operations Check” on 
page 45.
[Optional Stand]
10
Attach the optional stand to the unit.
•Each stands has four holes (A, B, C, D).
1) Attach the stand to the unit with the locking 
caster up.
2) When attaching the unit to the stand at  normal height (1,830 mm [6  
2/32 ]), tighten 
the two screws (included in the stand) with 
1 washers using the hexagonal wrench 
through holes A and C.
[Normal height]
Note
• Use the washer included with the electronic 
board. Do not use the washer included with 
the stand.
• Do not tighten the screw too much. This may 
deform the stand.
• By tightening the two screws with washers 
through holes A and B, the unit will be 
positioned 100 mm (3
15/16) higher than 
normal height (1,930 mm [6  4]).
[higher than normal height]
Wall-mounting hardware
A
B
C
1
Washer
Screw
A
B
C
UB5838C-PJQXC0259ZA_mst.book  43 ページ  ２００９年５月２６日　火曜日　午後２時５９分 
						

							Assembling the unit
44
11
Stand the unit up.
12
Attach the rivets (included in the stand) to the 
holes in the stand that are not already in use.
• normal height: 2 places
• higher than normal height: 4 places
13
Attach the clamp to the stand.
•Attach the 3 clamp for the power cord to the 
upper side of the stand, on the control box 
side.
UB5838C-PJQXC0259ZA_mst.book  44 ページ  ２００９年５月２６日　火曜日　午後２時５９分 
						

							45
Installation
Electronic Board Operations Check
■Before Operation Check
1
Wipe the screen film surface.
•Soak a soft cloth with water, wring well, and 
wipe the screen film surface.
Note
• Do not wipe the screen film surface with paint 
thinner, benzene, or cleaners that contain 
abrasives. Doing so may cause discoloration.
• Do not wipe the screen film surface with a dry 
cloth. Doing so may create static electricity.
2
Attach the power cord.
•Securely fit the supplied power cord in the AC 
inlet of the control box.
3
Remove the battery protection sheet.
■ Setting the time
Set the time as follows.
1
Turn the power switch on.
•The time set-up screen is displayed 
automatically when the power switch is turned 
on for the first time.
If the time set-up screen is not displayed even 
when the power switch is turned on, press the 
Set-up Key   to enter the setting mode, 
then press the Set-up Key ( ) repeatedly to 
select the time set-up mode, and then press 
the Advance Key ( ).
2
Set the current time.
The value can be changed by pressing the Set-
up Key ( ), and select the setting by pressing 
the Advance Key ( ).
3
Press the Mode Key ( ) to set the time.
Power cord
Battery protection sheet
UB5838C-PJQXC0259ZA_mst.book  45 ページ  ２００９年５月２６日　火曜日　午後２時５９分 
						

							Electronic Board Operations Check
46
■ Operation Check Procedure
After assembling the unit and setting the time, perform the procedures presented in the following table to make sure 
it functions properly.
StepPoints to Check
ConditionSolutions
1Turn the power switch on. The standby message is displayed 
after the initial message is 
displayed. (Normal operation)
Display does not appear. Check the power cord. (See step 2 on page 45.)
An error code appears on the 
display. Contact the store or dealer from 
which the unit was purchased.
2Press the Advance Key. Screen is fed.
(Normal operation)
The screen film surface is not fed 
smoothly. Contact the store or dealer from 
which the unit was purchased.
There are strange noises.
3Connect a USB flash memory 
device or SD memory card. The USB flash memory device or 
SD memory card installed is shown 
on the display. (Normal operation)
(If not) Contact the store or dealer from  which the unit was purchased.
4Use the accessory marker 
to draw a large   
across the entire 
scannable area of the 
screen film surface.
• For information on the 
scannable area, refer to 
“Screen Film” on page 12.
Press the Start/Stop Key. The screen film moves smoothly 
and the scanned image appears on 
the display.
(Normal operation)
(If not) Contact the store or dealer from 
which the unit was purchased.
5Zoom in on several areas of the 
scanned image.
(See page 18 and 19.) A black or white horizontal line 
appears on the scanned image, or 
the image scanned is dark or blank. Check the strong lighting.
The entire scannable area is not 
scanned. Contact the store or dealer from 
which the unit was purchased.
6Turn off the power switch, then 
turn back on after 3 minutes.The standby message is displayed 
after the initial message is 
displayed. (Normal operation)
The time is not correct. Check the battery.
(See step 3 on page 45.)
UB5838C-PJQXC0259ZA_mst.book  46 ページ  ２００９年５月２６日　火曜日　午後２時５９分 
						

							47
Installation
Repacking
Perform Assembly Steps 2 through 13 on pages 41 - 44 in reverse to repack the unit and accessories. Use the joints 
to fasten the shipping box.
Note
•When handling the screen unit, grasp the side cover on either side of screen. Do not grasp the screen film surface, 
as this may scratch it.
UB5838C-PJQXC0259ZA_mst.book  47 ページ  ２００９年５月２６日　火曜日　午後２時５９分 
						

							48
Wall-Mounting Construction
■Checking the Wall
When mounting on a wall, consult with your building’s owner, caretaker or construction manager to determine if the 
wall strength is sufficient to install this unit. For safety, install this unit only after thoroughly understanding the type of  
walls, the appropriate types of screws and the construction method (page 51).
Note
• Do not attach the electronic board to mortared walls. Accidental electric leakage from the wall-mounting 
fixture screws to metal laths or wire laths can cause heat, smoke or fire.
1. Necessary Tools and Parts (not included with the product) Drill, Screwdriver, Measuring tape, Level
8 screws (M6 size)
2. Before Starting 1. Make sure that the wall is strong enough to support the following weight.For UB-5838C: 1,373 N [140 k gf (309 lbf)]
For UB-5338C: 1,275 N [130 k gf (287 lbf)]
Note
• If necessary, reinforce the wall so that it is strong enough to support the unit.
2. Make sure that the location is large enough to accommodate the unit. For UB-5838C: 1,125 mm (H) ×  1,998 mm (W) [3 8
19/64  (H)  × 6  643/64  (W)]
For UB-5338C: 1,125 mm (H) ×  1,636 mm (W) [3 819/64  (H)  × 5  427/64  (W)]
3. Make sure that the AC outlet is within 3 m (9  10
1/8 ) of where the unit will be mounted and that it will not be 
behind the unit.
UB5838C-PJQXC0259ZA_mst.book  48 ページ  ２００９年５月２６日　火曜日　午後２時５９分 
						

							Wall-Mounting Construction49
Installation
■Installing the Wall-Mounting Fixtures
1
Ensure that the wall is strong enough to support the unit.
For UB-5838C: 1,373 N [140 k gf (309 lbf)]
For UB-5338C: 1,275 N [130 k gf (287 lbf)]
2
Using the measuring tape and level, mark the 8 locations to insert the screws.
Note
• Note the difference in the hole position for UB-5838C and UB-5338C.
• Make sure that the position of the holes are level and perpendicular to each other (i.e., the unit will not be 
crooked).
• The lateral tolerance of the hole position of the wall-mounting fixture is ± 1.5 mm (
1/16).
3
Drill 8 holes for the wall-mounting fixtures.
• Drill holes that are appropriate for the screws you are using.
UB-5838C: 1,927 mm (6  37/8 )
UB-5338C: 1,565 mm (5  15/8 )
86 mm (3
25/64 ) 86 mm (325/64)
1,009.5 mm (3  3
3/4 )
50 mm (1
31/32 )5 0mm  (131/32)
432 mm (1  5
1/64 ) 35.5 mm (1
25/64
)
35.5 mm (125/64 )
11 . 5 m m  (
29/64)
23 mm
(
29/32
)
UB5838C-PJQXC0259ZA_mst.book  49 ページ  ２００９年５月２６日　火曜日　午後２時５９分 
						

							Wall-Mounting Construction
50
4
Install the wall-mounting  fixtures using the 4 screws.
• 2 screws are used for each wall-mounting plate.
The remaining 4 screws are used after installing the unit on the wall.
Note
• Screws (8 count) are not included with the product. Please purchase screws with a size of M6, appropriate 
for your type of wall.
• Tighten the wall-mounting hardware so that it will not become loose.
• When drilling the holes and installing the wall-mounting fixtures, follow the procedure in “Wall Types and 
Installation Procedures” (page 51).
5
Mount the unit on the wall.
•Refer to “Assembling the unit” (page 40).
Wall-mounting fixture UB-5838C: 1,927 mm (6
 3
7/8 )
UB-5338C: 1,565 mm (5  15/8 )
86 mm (3
25/64)
50 mm (1
31/32)
50 mm (1
31/32) 1,009.5 mm (3
 3
3/4)
432 mm (1  5
1/64 )
UB5838C-PJQXC0259ZA_mst.book  50 ページ  ２００９年５月２６日　火曜日　午後２時５９分