Panasonic Electronic Board UB-5310 Operating Instructions

31
Table of Contents
Before installing this set, please read this manual completely.
CLASS 1 LED PRODUCT
WA R N I N G
DO NOT INSTALL THIS OPTION EXCEPT 
QUALIFIED SERVICE PERSONNEL.
CAUTION
SAFETY CHECK MUST BE DONE BY 
QUALIFIED SERVICE PERSONNEL AFTER 
INSTALLING THIS OPTION.
Installation Manual
page
Assembling the Electronic Board . . . . . . . . . . . . . . . . . . . . . .   32
● Accessories for assembling  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  32
● Assembly  . . . . . . . . . ....

32
Assembling the Electronic Board
■Accessories for assembling
The package includes the parts for setting up the electronic board shown below. Make sure that all of these parts 
are included in the package before proceeding.
* These names [Wall-mounting fixture (upper)/Wall-mounting fixture (lower)] are used for installing on the wall.
Part NameIllustration/QuantityRemarks
Board attachment (upper)
[*Wall-mounting  fixture (upper)]
Board attachment (lower)
[*Wall-mounting  fixture (lower)]
Cover (upper)...

33
Installation Manual
■Assembly
1Assemble the optional stand or wall-mounting fixture.
■If you are using a stand, refer to page 42.
■If you are using a wall-mounting fixture, refer to page 46.
2Remove the electronic board from the shipping box.
Remove the joints, then remove the electronic board from the shipping box.
Caution
 When removing the screen unit, grasp the side cover on either side of screen.
Do not grasp the screen film surface, as this may scratch it.
 The shipping box, cushioning...

34
3Collapse the carton box.
Remove the tape and the staples on 
the unopened side of the carton box, 
then collapse the box.
4Remove the protective plastic bags.
Remove the protective plastic bag 
from the screen unit and printer unit. 
Set those units on the top of collapsed 
shipping box and remove the 
cushions.
Caution
 Touch the screen film surface gently to avoid 
any damage.
5Attach the screen unit to the 
optional stand or wall mounting 
fixture.
■If you are using the stand, refer to 
page 42....

35
Installation Manual
8Extend the screen unit.
Open the center and right panels of 
the screen unit as shown below and 
remove the cushion.
Caution
 Touch the screen film surface gently when 
opening the screen unit. 
9Unlock the hook.
Unlock the hook connected to the 
center and right panels. Extend the 
screen unit and remove the cushion 
behind the screen.
 
Caution
 Touch the screen film surface gently when 
opening the screen unit. 
10Extend the screen unit.
Hang the right hook of the screen unit...

36
■Adjusting the level of the screen 
unit (Step 12–15: only for use of 
the optional stand)
At the lowest level of the board attachment frame, 
the printer cannot be installed. Raise the level of 
the screen unit as follows.
 Please lock the casters when you adjustment the 
screen height. Refer to Operating Instructions 
page 5.
12Loosen the height adjustment 
handles on the board attachment 
frame.
13Hang the step frame on the center 
of the reinforce pipe.
Hold the center of the board attachment...

37
Installation Manual
15After hanging the screen, fix the 
stopper screw (left side only).
This prevents the user from adjusting 
the screen height at the lowest level by 
mistake.
16Attach the printer unit.
Hang the hooks of the printer unit on 
the square holes of the board 
attachment (lower).
Caution
• When attaching the printer unit, make sure the  cable is not caught between the metallic frame 
and the printer unit.
17Tighten the screws for the printer 
unit.
Use four screws for the optional stand...

38
18Connect the cables (2) to the screen 
panel connectors.
19Remove the folding support screw 
on the front side of the screen unit, 
then store the folding support on 
the back side.
20Attach the cover (upper).
Hook the cover with the projections on 
both sides, then cover the top of the 
board attachment (upper).
21Store the shipping screws for fixing 
the screen panels, the screw for the 
folding frame and the wrench in the 
tool box on the top of the printer 
unit.
Folding support screw
Folding...

39
Installation Manual
22Attach the cover (lower).
(1) Push the cover in the direction of the arrow until it clicks.
(2) Fix the cover with the wing bolt.
23Attach the power cord.
Securely fit the supplied power cord 
into the AC inlet on the printer unit.
24Attach the paper holders.
Attach the paper holders to the printer 
section in numerical order of the 
arrows (1), (2), (3) and (4).
25Attach the rear cover. (only for use 
of the optional stand)
• After peeling off the cover sheets of the  adhesive...

40
Electronic Board Operations Check
After assembling the electronic board, perform the procedures presented in the following table to make sure it 
functions properly.
Step
Points to Check
SymptomSolutions
1Turn on the power switch.
“ ” flashes after “ ” lights up.(Normal operation)
(If not) Check power cord and  
cables.
(See step 23 on page 39 
and step 18 on page 38.)
2Open the printer door and load the 
copy paper, then close the printer door.
 loading the copy paper procedure 
(refer to the...