Panasonic Electronic Board UB-5310 Operating Instructions

11
Operating Instructions
Making Copies
This section describes how to copy text and illustrations drawn on the screen.
1
Turn the power switch on by pressing the “ I ” side 
of the power switch.
 The unit is ready for use when “ ” is displayed on the 
multi-copy/error indicator.
 The screen will move to home position and stop.
 Confirm the ERROR Indicator “ ” is off.
(If not, refer to “Loading the copy paper”.)
 When not in use, be sure to turn the power off.
2
Press the Copy Key  .
 Text and...

Making Copies
12
■Copy types and procedures
3M® is a registered trademark of 3M Corporation.
Copy TypeProcedure
Copying the front of 
the screenPress .
Copying the back of 
the screen Press   to move the screen to be copied to the front.
Press .
Making multiple 
copies (up to 9) Select the number of copies (1 to 9) by pressing   as 
necessary.
Press .
Press  to stop copying in mid-operation.
Making 2-screen 
copies
 Copying the front and 
back of the screen on a 
single sheet of paper 
Press .
Copying...

13
Operating Instructions
Paper Jams
To release jammed paper:
1
Push the door open button and open the printer 
door.
2
Remove the jammed paper by pulling the paper roll 
to the direction A. If the jammed paper is still in the 
cutter cover, remove it using tweezers from slot B.
3
Cut the paper straight as shown in the figure.
4
Pass the paper over the paper feed roller and under 
the cutter cover, then through the output port about 
4cm (1
1/2inches). (Refer to step 4 on page 10.)
In case paper cannot...

14
Screen Height Adjustment
The screen can be adjusted at 3 levels except for the lowest level. The lowest level of the board attachment frame is 
designed for installation of the screen, so the printer cannot be attached at this level. Adjust the level of the screen 
unit as follows.
Please lock the casters when you adjust the screen height. (Refer to page 5.)
1
Loosen the height adjustment handles.
2
Hang the step frame on the reinforce pipe.
Lift the board attachment (lower) by stepping on 
the step...

Screen Height Adjustment
15
Operating Instructions
4
Tighten the height adjustment handles.
Be sure to tighten the height adjustment handles 
firmly after adjusting the level of the screen.
5
Store the step frame by hanging it on the board 
attachment (upper).
Height 
adjustment 
handles
Height 
adjustment 
handles
Step frame
Board attachment 
(upper)
UB-5310_MECA.book  15 ページ  ２００３年５月１５日　木曜日　午後５時２３分 

16
Computer Interfacing
 Panasonic Document Management System (hereafter Panasonic-DMS) uses the TWAIN driver to scan images 
drawn on the screen.
 The Panasonic-DMS has a capability of managing documents (image files).
 The printer driver allows the printer to print documents from your computer.
■System requirements
* The computer interfacing function of the UB-5310 is not available in Windows NT® 4.0.
* If you connect the electronic board to a USB hub, it is not guaranteed to work.
* Please note...

Computer Interfacing
17
Operating Instructions
■Installing the driver and software
Installing the USB and Printer driver
1Power on your computer and start 
Windows.
2Power on the electronic board, and 
connect the unit and your computer 
with a USB cable.
3When “USB Composite Device” is 
detected, click the [Next] button.
4Click on the “Search for the best 
driver for your device. 
(Recommended).” check button and 
click the [Next] button.
5Insert the CD-ROM into the CD-ROM 
drive. When the Setup window...

Computer Interfacing
18
1Power on your computer and start 
Windows.
2Power on the electronic board, and 
connect the unit and your computer 
with a USB cable.
3When “Panaboard-UB5 USB Device” 
is detected, click on the “Specify the 
location of the driver (Advanced)” 
check button and click the [Next] 
button.
4Insert the CD-ROM into the CD-ROM 
drive. When the Setup window appears, 
click the  (close button) to close it.
5Select the “Specify a location:” only, 
then specify “D (CD-ROM drive letter):...

Computer Interfacing
19
Operating Instructions
Special Note for Windows 98/Me
If your computer had Windows 98/Me pre-installed 
and the original Windows 98/Me CD-ROM or diskettes 
were not included. In this situation, please try to locate 
the necessary files by following the methods 
described below or refer to your computer’s User’s 
Guide for more details.
Method-1:
Specify the Windows 98/Me backup file location in 
the hard disk of your computer.
Generally, the Windows 98/Me backup files are 
located...

Computer Interfacing
20
1Power on your computer and start 
Windows.
 Log on as an administrator.
2Power on the electronic board, and 
connect the unit and your computer 
with a USB cable.
3When “Welcome to the Found New 
Hardware Wizard” dialog box appears, 
click the [Next] button.
4When “Panaboard-UB5 USB Device” 
is detected, click on the “Search for a 
suitable driver for my device 
(Recommended)” check button and 
click the [Next] button.
5Insert the CD-ROM into the CD-ROM 
drive. When the Setup...