Panasonic Electronic Board UB-5310 Operating Instructions

Computer Interfacing
21
Operating Instructions
1Power on your computer and start 
Windows.
 Log on as an administrator.
2Power on the electronic board, and 
connect the unit and your computer 
with a USB cable.
3When “Panaboard-UB5 USB Device” 
is detected, click on the “Install from a 
list or specific location (Advanced)” 
check button and click the [Next] 
button.
4Insert the CD-ROM into the CD-ROM 
drive. When the Setup window appears, 
click the  (close button) to close it.
5Select the “Include...

Computer Interfacing
22
Installing Panasonic-DMS software and 
TWAIN driver
When an old version of Panasonic-DMS is already 
installed, remove it and install the new version of 
the software in the same folder.
1Power on your computer and start 
Windows.
 Log on as an administrator for Windows 
2000 or Windows XP.
2Insert the CD-ROM into the CD-ROM 
drive. The Setup window will appear 
automatically.
 Depending on the operating system or the 
settings that you are using, the Setup 
window may not...

Computer Interfacing
23
Operating Instructions
■Removing the driver and software
Removing Panasonic-DMS software 
and TWAIN driver
If you need to remove the Panasonic-DMS 
software and TWAIN driver, perform the following 
steps.
1Power on your computer and start 
Windows.
 Log on as an administrator for Windows 
2000 or Windows XP.
2Click [Start], move the pointer to 
[Programs]–[Panasonic]–[Panasonic 
Document Management System]–
[Uninstall].
(For Windows XP, [All Programs] 
instead of [Programs].)...

Computer Interfacing
24
■Panaboard Operation Panel
It is possible to perform the same operations as with the electronic board control panel (page 9) from the following 
Panaboard Operation buttons.
Note: While the Panaboard Operation Panel is displayed, the Copy Key and 2-Screen Copy Key on the electronic 
board control panel are used for scanning images into the computer.
Panel NameDescription
Contrast 
IndicatorThis lamp indicator displays the contrast used during scanning or 
copying.
Indicator off:...

Computer Interfacing
25
Operating Instructions
Status Box
The status box displays the status of the TWAIN driver 
and the electronic board.
Stand by: The electronic board is stand by.
Both of the Panaboard Operation Panel 
and the electronic board control panel are 
operational.
Rotating: The electronic board is rotating the 
screen.
Copying: The electronic board is copying the 
screen.
Scanning: The electronic board is now scanning the 
images on the screen.
Converting: Indicates that the image data is...

26
Daily Care and Maintenance
Always turn off the power switch and unplug the power plug when cleaning outside and inside the unit.
■Cleaning the screen and the unit
Gently wipe the screen film and unit with a water-
dampened cloth that has been thoroughly wrung.
 Use a kitchen cleaner diluted with water for hard-to-
clean stains.
 If you accidentally write on the board with an oil-based 
marker, wipe with a small amount of ethyl alcohol.
 Use a neutral kitchen cleaner diluted with water for...

Daily Care and Maintenance
27
Operating Instructions
2
Dampen the tip of a cotton swab in ethyl alcohol 
and gently wipe the printer head.
 Never touch the printer head or the surrounding area 
with your hands as this may disable copying.
3
Wipe any dirt or stains off the paper feed roller.
 Dampen a soft cloth with neutral kitchen cleaner 
diluted in water, wring the cloth thoroughly, and wipe 
the entire surface of the roller while rotating it. If this 
does not remove all dirt, wipe with a cloth...

28
Troubleshooting
Treat problems according to the information given in the table below. If problems still persist, call your dealer for 
service.
SymptomCare and RemedySee
Page
Power switch is on but the 
indicator is off.Check that the power plug is securely plugged in.
(If the indicator still does not light, turn the power off and on again.)–
Copied copy paper will not 
come out.The unit is out of copy paper. (The Error Indicator flashes “ ”.)
Load new paper.10
The printer door is open. (The Error...

Troubleshooting
29
Operating Instructions
■Meanings of error codes
The following table describes the meaning of each of the symbols which may flash in the Multi-Copy/Error 
Indicator.
If other indications such as “ ” appear, call your dealer.
IndicationCauseRemedySee
Page
(Error)Data transfer error Connect the USB cable securely. 16
(Screen)The screen will not move.Remove any chart paper attached to 
the screen and slowly move the screen 
by hand.–
(Paper)No paper Load the copy paper roll. 10
The printer...

30
Specifications
■Option and Separately available
* Using a copy paper roll with a smaller core could cause paper jam.
Model No.UB-5310
General
Power supply AC 100 –120 V, 50/60 Hz
Power consumption 
(Operational/Standby) 1.4 A
External dimensions 
(Height  × Width  × Depth, 
without stand) 1440 mm 
× 1372 mm  × 233 mm
(4  8
11/16  ×  4  6  ×  93/16 )
Mass (without stand/
with board attachment) 23 k
g (50.7 lbs.)
Ambient operating conditions Temperature: 10–35 °C (50–95
°F)
Humidity: 30–80% RH
Writing...