Panasonic Electronic Board UB-5310 Operating Instructions

							11
Operating Instructions
Making Copies
This section describes how to copy text and illustrations drawn on the screen.
1
Turn the power switch on by pressing the “ I ” side 
of the power switch.
 The unit is ready for use when “ ” is displayed on the 
multi-copy/error indicator.
 The screen will move to home position and stop.
 Confirm the ERROR Indicator “ ” is off.
(If not, refer to “Loading the copy paper”.)
 When not in use, be sure to turn the power off.
2
Press the Copy Key  .
 Text and illustrations on the screen will be copied and 
copies emerge from the output port.
 The copied paper holder can hold up to 5 copies.
(Note that exceeding the copied paper holder’s 
capacity may result in paper jams.)
 For details on making multiple copies, 2-screen copies 
and so on, see page 12.
 While copying, do not touch the paper, otherwise the 
paper may jam.
 Text or images in shades of yellow will not copy.
PUSH OPEN
Power 
Switch
Notes
PUSH OPEN
Output paper
Notes
UB-5310_MECA.book  11 ページ  ２００３年５月１５日　木曜日　午後５時２３分 
						

							Making Copies
12
■Copy types and procedures
3M® is a registered trademark of 3M Corporation.
Copy TypeProcedure
Copying the front of 
the screenPress .
Copying the back of 
the screen Press   to move the screen to be copied to the front.
Press .
Making multiple 
copies (up to 9) Select the number of copies (1 to 9) by pressing   as 
necessary.
Press .
Press  to stop copying in mid-operation.
Making 2-screen 
copies
 Copying the front and 
back of the screen on a 
single sheet of paper 
Press .
Copying chart 
paperChart paper can be attached to the screen as shown in the figure 
and copied. (Be sure to take the chart off the screen soon after 
copying is finished.)
 Wrinkles, slackness or folds in the chart when attached to the screen will show 
up in copies as dark shadows.
 Affix it to the screen with drafting tape made by 3M
®
 or other similar tape with 
medium adhesive.
UB-5310_MECA.book  12 ページ  ２００３年５月１５日　木曜日　午後５時２３分 
						

							13
Operating Instructions
Paper Jams
To release jammed paper:
1
Push the door open button and open the printer 
door.
2
Remove the jammed paper by pulling the paper roll 
to the direction A. If the jammed paper is still in the 
cutter cover, remove it using tweezers from slot B.
3
Cut the paper straight as shown in the figure.
4
Pass the paper over the paper feed roller and under 
the cutter cover, then through the output port about 
4cm (1
1/2inches). (Refer to step 4 on page 10.)
In case paper cannot go through, just put the paper 
on the paper feed roller and insert the top of the 
paper in the cutter cover as shown in the figure.
5
Close the printer door securely, using two hands.
 Use copy paper roll with a core diameter of 25.4 mm 
(1 inch) or more. Using a copy paper roll with a smaller 
core could cause paper jams.
 Once the door is closed, paper will feed and 
automatically cut. Remove and discard the small piece 
of paper.
PUSH OPEN
Door
Open
Button
Slot B A
Cutter cover
Cut
Paper feed 
roller
Cutter cover
Notes
UB-5310_MECA.book  13 ページ  ２００３年５月１５日　木曜日　午後５時２３分 
						

							14
Screen Height Adjustment
The screen can be adjusted at 3 levels except for the lowest level. The lowest level of the board attachment frame is 
designed for installation of the screen, so the printer cannot be attached at this level. Adjust the level of the screen 
unit as follows.
Please lock the casters when you adjust the screen height. (Refer to page 5.)
1
Loosen the height adjustment handles.
2
Hang the step frame on the reinforce pipe.
Lift the board attachment (lower) by stepping on 
the step frame.
Slide along the slide groove.
Do not handle the tray.
Adjust the screen height with two persons after 
installation.
3
Hang the screen in the desired slots of the slide 
plates.
Do not use slot 4.
Slot 4 cannot be used for screen height adjustment.
Confirm both sides of the screen are hung in the 
same height slots securely. Slot Adjustment Screen Height
Slot 1 Available 2000 mm (6 6
3/4 )
Slot 2 Available 1875 mm (6 113/16 )
Slot 3 Available 1750 mm (5 87/8 )
Slot 4 Cannot be used –
Height 
adjustment 
handles
Height 
adjustment 
handles
Lift
Slide 
groove
Down
Step frame
Board attachment 
(lower)
Reinforce pipe
Slot 4
Slot 3
Slot 2
Slot 1
UB-5310_MECA.book  14 ページ  ２００３年５月１５日　木曜日　午後５時２３分 
						

							Screen Height Adjustment
15
Operating Instructions
4
Tighten the height adjustment handles.
Be sure to tighten the height adjustment handles 
firmly after adjusting the level of the screen.
5
Store the step frame by hanging it on the board 
attachment (upper).
Height 
adjustment 
handles
Height 
adjustment 
handles
Step frame
Board attachment 
(upper)
UB-5310_MECA.book  15 ページ  ２００３年５月１５日　木曜日　午後５時２３分 
						

							16
Computer Interfacing
 Panasonic Document Management System (hereafter Panasonic-DMS) uses the TWAIN driver to scan images 
drawn on the screen.
 The Panasonic-DMS has a capability of managing documents (image files).
 The printer driver allows the printer to print documents from your computer.
■System requirements
* The computer interfacing function of the UB-5310 is not available in Windows NT® 4.0.
* If you connect the electronic board to a USB hub, it is not guaranteed to work.
* Please note that if more than one Panasonic electronic boards are connected in a USB tree, only one of those electronic 
boards will perform the computer interfacing.
■Contents of CD-ROM
The provided CD-ROM includes the following items.
USB driver
 Printer driver
 Panasonic-DMS software
 TWAIN driver
 View Manuals
 Adobe
® Acrobat® Reader
■Connecting the unit to a computer
Power on the electronic board, and connect the unit and your computer with a USB cable.
Caution:
* Use a shielded USB cable that is certified as logo by USB-IF.
When you connect the unit for the first time, install the USB and Printer driver to your computer.
 Windows 98 →  Page 17
 Windows Me →  Page 18
 Windows 2000 →  Page 20
 Windows XP →  Page 21
* When using Windows 98 or Windows Me, a floppy disk or CD-ROM for installing the operating system will also 
be necessary. (See page 19.)ComputerIBM
® PC/AT or compatible machine with a CD-ROM drive
CPUPe n t iu m
® II or higher processor
InterfaceUSB 1.1 (B connector)
OSWindows
® 98 / Windows® Millennium Edition / Windows® 2000 / Windows® XP
Memory64 MB or more (Windows 98/Me)
128 MB or more (Windows 2000)
256 MB or more (Windows XP)
HDAt least 40 MB free space (except saving space for image file)
USB cable
To your computer
UB-5310_MECA.book  16 ページ  ２００３年５月１５日　木曜日　午後５時２３分 
						

							Computer Interfacing
17
Operating Instructions
■Installing the driver and software
Installing the USB and Printer driver
1Power on your computer and start 
Windows.
2Power on the electronic board, and 
connect the unit and your computer 
with a USB cable.
3When “USB Composite Device” is 
detected, click the [Next] button.
4Click on the “Search for the best 
driver for your device. 
(Recommended).” check button and 
click the [Next] button.
5Insert the CD-ROM into the CD-ROM 
drive. When the Setup window appears, 
click the  (close button) to close it.
6Select the “Specify a location:” only, 
then specify “D (CD-ROM drive letter):
\UB-5xxx\UsbDrv\Win98-Me” in the 
text box, and click the [Next] button.
 Do not select the CD-ROM drive. It may 
cause installing a wrong USB driver.
7When the driver is found, click the 
[Next] button.
8When the installation of “USB 
Composite Device” driver is 
completed, click the [Finish] button.
9When “Unknown Device”* is 
detected, click the [Next] button.
10Click on the “Search for the best driver 
for your device. (Recommended).”
 
check button and click the 
[Next] button.
11Confirm that the “Specify a location:” 
is the same as step 6, click the [Next] 
button.
12When the driver is found, click the 
[Next] button.
13When the installation of “USB Printing 
Support” is completed, click the 
[Finish] button.
14When “Unknown Device”**  is 
detected again, repeat steps 9 to 13 to 
install 
“Panaboard-UB5 USB Device 
Driver”
.
15When “PanasonicPanaboard-UB5 
USB Printer (Letter)” is detected, click 
the [Next] button.
16Click on the “Search for the best driver 
for your device. (Recommended).”
 
check button and click the 
[Next] button.
17Confirm that the “Specify a location:” 
is the same as step 6, click the [Next] 
button.
18When the driver is found, click the 
[Next] button.
19Follow the on-screen instructions when 
the “Add Printer Wizard” executes.
20When the installation of “Panaboard-
UB5 USB Printer (Letter)” driver is 
completed, click the [Finish] button.
* In the case of Windows 98 Second Edition, 
“USB Printing Support” is detected.
** In the case of Windows 98 Second Edition, 
“Panaboard-UB5 USB Device” is detected.
 A floppy disk or CD-ROM for installing the operating 
system will also be necessary. (See page 19.)
Windows 98
UB-5310_MECA.book  17 ページ  ２００３年５月１５日　木曜日　午後５時２３分 
						

							Computer Interfacing
18
1Power on your computer and start 
Windows.
2Power on the electronic board, and 
connect the unit and your computer 
with a USB cable.
3When “Panaboard-UB5 USB Device” 
is detected, click on the “Specify the 
location of the driver (Advanced)” 
check button and click the [Next] 
button.
4Insert the CD-ROM into the CD-ROM 
drive. When the Setup window appears, 
click the  (close button) to close it.
5Select the “Specify a location:” only, 
then specify “D (CD-ROM drive letter):
\UB-5xxx\UsbDrv\Win98-Me” in the 
text box, and click the [Next] button.
 Do not select the CD-ROM drive. It may 
cause installing a wrong USB driver.
6When the driver is found, click the 
[Next] button.
7When the installation of “Panaboard-
UB5 USB Device Driver” is 
completed, click the [Finish] button.
8When “Panaboard-UB5 USB Printer” 
is detected, click on the “Specify the 
location of the driver (Advanced)” 
check button and click the [Next] 
button.
9Confirm that the “Specify a location:” 
is the same as step 5, click the [Next] 
button.
10When the driver is found, click the 
[Next] button.
11When the installation of “USB Printing 
Support” is completed, click the 
[Finish] button.
12When “PanasonicPanaboard-UB5 
USB Printer (Letter)” is detected, click 
on the “Specify the location of the 
driver (Advanced)” check button and 
click the [Next] button.
13Confirm that the “Specify a location:” 
is the same as step 5, click the [Next] 
button.
14When the driver is found, click the 
[Next] button.
15Follow the on-screen instructions when 
the “Add Printer Wizard” executes.
16When the installation of “Panaboard-
UB5 USB Printer (Letter)” driver is 
completed, click the [Finish] button.
 A floppy disk or CD-ROM for installing the operating 
system will also be necessary. (See page 19.)
Windows Me
UB-5310_MECA.book  18 ページ  ２００３年５月１５日　木曜日　午後５時２３分 
						

							Computer Interfacing
19
Operating Instructions
Special Note for Windows 98/Me
If your computer had Windows 98/Me pre-installed 
and the original Windows 98/Me CD-ROM or diskettes 
were not included. In this situation, please try to locate 
the necessary files by following the methods 
described below or refer to your computer’s User’s 
Guide for more details.
Method-1:
Specify the Windows 98/Me backup file location in 
the hard disk of your computer.
Generally, the Windows 98/Me backup files are 
located in the “WINDOWS\OPTIONS\CABS” folder. 
Type “C:\WINDOWS\OPTIONS\CABS” in the [Copy 
files from:] box on the “Copying Files...” dialog box, 
where “C:” is your Windows 98/Me boot drive and 
then click the [OK] button.
If the necessary files are found, the installation will 
proceed.
Otherwise, click the [Details...] button, a dialog box 
appears as shown below including the cabinet file 
name (*.CAB listed under the Description File) that 
contains the necessary file.
In this example, the cabinet file name is 
“DRIVER20.CAB”. (Note that the cabinet file name 
may vary depending on your computer.)To search for the file in your computer
1Click the [Start] button on the Task Bar 
and then click on 
[Find]–[Files or 
Folders...]
 (Windows 98) or [Search]–
[For Files or Folders...] (Windows Me).
2A dialog box appears prompting for a 
file name to be searched, type 
“DRIVER*.CAB” in the [Named:] 
(Windows 98) or [Search for files or 
folders named:] (Windows Me) box, 
choose “C:” in the [Look in:] box and 
check the box for [Include subfolders] 
(only for Windows 98).
3Click the [Find Now] (Windows 98) or 
[Search Now] (Windows Me) button. 
When the cabinet file is found, make a 
note of the folder name where the file is 
located.
4Return to the “Copying Files...” dialog 
box and type the folder name in the 
[Copy files from:] box. For example, 
type 
“C:\WINDOWS\OPTIONS\CABS”. 
Then click the 
[OK] button.
Method-2:
Create the Windows 98/Me backup diskettes and 
then specify the diskettes.
Depending on the computer, there is usually a tool 
from the manufacturer to create the Windows 98/Me 
backup diskettes in a Windows 98/Me pre-installed 
system. Please refer to your PC’s User’s Guide for 
more details on this tool.
Create the Window 98/Me backup diskettes by using 
this tool, and then install the USB and Printer driver by 
following the procedures from Step 1.
Note
UB-5310_MECA.book  19 ページ  ２００３年５月１５日　木曜日　午後５時２３分 
						

							Computer Interfacing
20
1Power on your computer and start 
Windows.
 Log on as an administrator.
2Power on the electronic board, and 
connect the unit and your computer 
with a USB cable.
3When “Welcome to the Found New 
Hardware Wizard” dialog box appears, 
click the [Next] button.
4When “Panaboard-UB5 USB Device” 
is detected, click on the “Search for a 
suitable driver for my device 
(Recommended)” check button and 
click the [Next] button.
5Insert the CD-ROM into the CD-ROM 
drive. When the Setup window appears, 
click the  (close button) to close it.
6Select the “Specify a location” only, 
then click the [Next] button.
 Do not select the CD-ROM drive. It may 
cause installing a wrong USB driver.
7Specify “E (CD-ROM drive letter):
\UB-5xxx\UsbDrv\Win2K-XP” in the 
text box, and click the [OK] button.
8When the driver is found, click the 
[Next] button.
9Although “Digital Signature Not 
Found” dialog box appears, click the 
[Yes] button to continue the installation.
10When the installation of “Panaboard-
UB5 USB Device Driver” is 
completed, click the [Finish] button.
11When “Welcome to the Found New 
Hardware Wizard” dialog box appears 
again, click the [Next] button.
12When “Unknown” is detected, click on 
the “Search for a suitable driver for 
my device (recommended)” check 
button and click the [Next] button.
13Select the “Specify a location” only, 
then click the [Next] button.
 Do not select the CD-ROM drive. It may 
cause installing a wrong USB driver.
14Confirm that the “Copy 
manufacturer’s files from:” is the 
same as step 7, click the [OK] button.
15When the driver is found, click the 
[Next] button.
16Although “Digital Signature Not 
Found” dialog box appears, click the 
[Yes] button to continue the installation.
17When the installation of “Panaboard-
UB5 USB Printer (Letter)” driver is 
completed, click the [Finish] button.
 The standard printer name is “Panaboard-UB5 USB 
Printer (Letter)”.
Windows 2000
UB-5310_MECA.book  20 ページ  ２００３年５月１５日　木曜日　午後５時２３分