Panasonic Electronic Board UB-5310 Operating Instructions

							41
Installation Manual
Repacking
Perform Assembly Steps 2 through 24 in reverse to repack the electronic board and accessories. Use the joints to 
fasten the shipping box to the lower box.
Caution
 When handling the screen unit, grasp the side cover on either side of screen.
Do not grasp the screen film surface, as this may scratch it.
Board attachment (lower)
Board attachment (upper)
Copy paper roll
Power cord
Cover (upper)
Cover (lower)
Markers
Screen unitManuals, CD-ROM
Printer unitEraserPaper holder ï
·ïAB
Joint Screws and spacers
UB-5310_MECA.book  41 ページ  ２００３年５月１５日　木曜日　午後５時２３分 
						

							42
Assembling the Optional Stand (UE-608005)
■Accessories
The package box for the optional stand includes the parts noted below; please confirm that all parts are present 
before beginning installation
.
The accessory Wrench is required when disassembling the electronic board; please store it carefully for future use.
*1 A screw (short)   is used for the stopper screw of step 15 on page 37.
●
Before assembly, be sure to lock the casters.
No.Part nameIllustrationQ’tyNo.Part nameIllustrationQ’ty
Base pipe 2 Screw 2
Reinforce pipe 1Height 
adjustment
handle4
Extension pipe 
S1Nut 4
Extension pipe 
L 
(not use)1Cap 2
Side pipe 2 Step frame 1
Slide plate 
(Left)1Fall-preven-
tion extension 
leg4
Slide plate 
(Right)1Wrench
(for stand)1
Fixing plate 2 Rear cover 1
Screw (long) 12 Rivet 6
Screw (short)
11*
1Wa she r 8
Locking the casters
(Push this side)
Releasing the lock
UB-5310_MECA.book  42 ページ  ２００３年５月１５日　木曜日　午後５時２３分 
						

							43
Installation Manual
■Assembly
1Assembling the stand
■Assembling the fall-prevention extension legs
The fall-prevention extension legs are effective in increasing the safety of the electronic 
board.
Caution
 Install and always set the fall-prevention legs when using the stand.
 When tightening the screws  , hold the nut   with pliers. 
■Assembling the stand
 Assemble the side pipes with the slide sheets facing inside.
Fall-prevention extension legs Caster locks are attached
to the back side.
Slide sheet
Side pipe
Base pipe
Extension pipe S
Base pipeReinforce pipe
Slide sheet
UB-5310_MECA.book  43 ページ  ２００３年５月１５日　木曜日　午後５時２３分 
						

							44
2Assembling the board attachment frame
 The board attachments (upper and lower) are supplied with the electronic board.
 Place the board attachments and the slide plates with their stamps facing up and assemble them matching 
their same stamps.
3Attach the board attachment frame to the stand.
Details of the procedures are as follows.
Step A Attach the fixing plate   to the board attachment frame.
Stamp “UL”
Stamp “LL”Stamp “UR”
Stamp “LR”Board attachment (upper)
Slide plate
(right)
Board attachment (lower) Slide plate
(left)
Step E
Step D
Step A Step B
Step CStep D
Step C Step A
Slide 
plateFixing 
plate
Cap
Height 
adjustment
handle Screw Height 
adjustment
handle
Fixing plateSide pipe
Side pipe
The caster locks 
are attached to 
the back side.
The wider side is front.
UB-5310_MECA.book  44 ページ  ２００３年５月１５日　木曜日　午後５時２３分 
						

							45
Installation Manual
Step B Place the screws with the board attachment frame in the grooves of the side 
pipes.
Step C Insert the screws   into the side pipes from the inside.
Step D Install and secure the height adjustment handles  .
Step E Fix the caps   to the side pipes.
4Assemble and install the electronic board.
Refer to pages 33 to 39.
5Insert and keep the wrench in the holder on the cover lower.
Board attachment frame
Side pipe
Side pipe Fixing plate
Screw
Wrench (for stand)
Cover (lower)
UB-5310_MECA.book  45 ページ  ２００３年５月１５日　木曜日　午後５時２３分 
						

							46
Wall-mounting
■Wall-mounting fixture
The wall-mounting fixture includes the board attachment (upper and lower) supplied with the unit.
Before attempting installation of this wall-mounting fixture, we strongly recommend consulting with the building 
manager, engineer, or architect. The installer needs to know the type of construction used for the wall intended for 
this installation and the location of wall studs. Selection of hardware is critical for safe wall-mounting, and 
depends on the nature of wall construction. Installation should not occur until this consultation takes place.
Caution
 Do not attach the electronic board to mortared walls. Accidental electric leakage from the wall-mounting 
fixture bolts to metal laths or wire laths can cause heat, smoke or a fire.
I. Tools required:
A minimum of four (4) pieces of appropriate wall-support hardware (molley, toggle, etc.)
NOTE: THIS HARDWARE MUST BE LOCALLY PROCURED, IT IS NOT INCLUDED IN THE PRODUCT.
Drill (and drill bit of correct size) for hardware installation
Screw driver (Both phillips (+) and slotted (–) will be required.)
Tape measure
Tape or thumb-tacks (2 pcs)
Bubble type level
II. Pre-requisites
1. Before installation, make sure that the wall intended for installation is capable of supporting flush-
mounted.
80 kgf (176 lbs.).
2. The position of the intended installation is of adequate size for the selected Panaboard.
1,440 mm (H) × 1,372 mm (W) [56.7 (H) × 54.0 (W)].
3. An outlet is within 3 m (118.1 ), and not located behind the Panaboard.
UB-5310_MECA.book  46 ページ  ２００３年５月１５日　木曜日　午後５時２３分 
						

							47
Installation Manual
■Wall-mounting procedure
1Confirm that the wall is strong enough to  support the weight of the electronic board.
Caution
The wall must be capable of suppor ting at least  784N [80 k gf (176 lbs.)]. 
21) Assemble the wall-mounting template by  taping the Wall-mounting template 1
(TOP) to Wall-mounting template 2 (BOTTOM).
2) Tape the wall-mounting  template on the wall.
• When taping the template on the wall, make sure it is level.
31) Drill holes in the wall at the 4 spots  indicated by  and , or  and  for the
wall-mounting fixtures.
 Holes on the wall-mounting fixture are 1/4   in diameter.
2) After removing the wall-mounting templa te, attach the wall-mounting fixtures 
with the appropriate wall-mounting hardware.
 Refer to the section “Attaching the wall-mounting fixtures” (page 48) for drilling in the wall and attaching the 
mounting fixtures.
 Refer to steps 2 to 23 on pages 33 to 39 for attaching the printer and the screen.
ACBC
AB
C
A B
C
AB
C
AB
C
Wall-mounting 
template
Wall-mounting hardware
Board attachment (upper)
(Wall-mounting fixture upper)
Board attachment (lower)
(Wall-mounting fixture lower)
Wall-mounting hardware
900
 m
m (
2 
 
1 17/1
6 )
940 mm
(3
 11  )
Remove the 
edge cover.
Remove the 
edge cover.
8
12
 m
m
 (
2 
 
8  
)
Installation_MECA.fm  47 ページ  ２００３年５月１５日　木曜日　午後８時２６分 
						

							48
■Attaching the wall-mounting fixtures
The electronic board must be mounted with the method most suited to the material of the wall.
Three methods are presented here.
(Other options may be available in your area.)
●
Attaching to metal or concrete walls
Stud plugs (sold in stores) are needed.
●
Attaching to plasterboard walls
Split-wing toggles (sold in stores) are needed.
Drill four holes in the wall.
For the correct hole size, refer 
to the instructions for the 
particular stud plugs used.
Insert each bolt through a hole 
in the wall-mounting fixture and 
tighten until the wall-mounting 
fixture is securely fixed to the 
wall. Drill bit
Metal or concrete
wall
Stud plug
Insert a stud plug in each hole.
Wall-mounting
fixture
Bolt
Inser t each bolt through a hole 
in the wall-mounting fixture and 
into the hole in the wall beneath 
so that the arms of the split-
wing toggle are horizontal. For 
the correct hole size, refer to the 
instructions for the particular 
split-wing toggles used.
After the arms expand, pull the 
wall-mounting fixture out until 
the arms of the split-wing toggle 
grip firmly into the wall.
Tighten each bolt until the wall-
mounting fixture is securely 
fixed to the wall. PlasterboardSplit-wing toggle
Wall-mounting
fixture
Bolt
ArmsArms
UB-5310_MECA.book  48 ページ  ２００３年５月１５日　木曜日　午後５時２３分 
						

							49
Installation Manual
●Attaching to wooden walls
Use wood screws (sold in stores).
For the correct hole size, refer 
to the instructions for the 
particular wood screws used. Wall-mounting fixture
Wood screw
Wooden wall
UB-5310_MECA.book  49 ページ  ２００３年５月１５日　木曜日　午後５時２３分 
						

							Panasonic Digital Document Company
A Unit of Matsushita Electric Corporation of America
Two Panasonic Way, Secaucus, New Jersey 07094
© 2002-2003 Panasonic Communications Co., Ltd.
Printed in Japan
PJQXB0050ZA  K0503M0
UB-5310_MECA.book  50 ページ  ２００３年５月１５日　木曜日　午後５時２３分