Panasonic Electronic Board UB-5310 Operating Instructions

							31
Table of Contents
Before installing this set, please read this manual completely.
CLASS 1 LED PRODUCT
WA R N I N G
DO NOT INSTALL THIS OPTION EXCEPT 
QUALIFIED SERVICE PERSONNEL.
CAUTION
SAFETY CHECK MUST BE DONE BY 
QUALIFIED SERVICE PERSONNEL AFTER 
INSTALLING THIS OPTION.
Installation Manual
page
Assembling the Electronic Board . . . . . . . . . . . . . . . . . . . . . .   32
● Accessories for assembling  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  32
● Assembly  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  33
Electronic Board Operations Check . . . . . . . . . . . . . . . . . . . .   40
Repacking  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   41
Assembling the Optional Stand (UE-608005)  . . . . . . . . . . . .   42
● Accessories  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  42
● Assembly  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  43
Wall-mounting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   46
● Wall-mounting fixture  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  46
● Wall-mounting procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  47
● Attaching the wall-mounting fixtures . . . . . . . . . . . . . . . . . . . . . . .  48
UB-5310_MECA.book  31 ページ  ２００３年５月１５日　木曜日　午後５時２３分 
						

							32
Assembling the Electronic Board
■Accessories for assembling
The package includes the parts for setting up the electronic board shown below. Make sure that all of these parts 
are included in the package before proceeding.
* These names [Wall-mounting fixture (upper)/Wall-mounting fixture (lower)] are used for installing on the wall.
Part NameIllustration/QuantityRemarks
Board attachment (upper)
[*Wall-mounting  fixture (upper)]
Board attachment (lower)
[*Wall-mounting  fixture (lower)]
Cover (upper)
Cover (lower)
Screws and spacers For screenFor printer 
and screen For cover For screen For screen Screen
Page 35, Step 11
Printer Page 37, Step 17
Cover (lower) Page 39, Step 22
Paper holder 
Paper holder  Wrench
Power cord
Wall-mounting  template Use the Wall-mounting 
template1 and 2 by 
pasting them together.
(Long)(Short)
A
B
1
1
1
1
6616
1
1
1
Q’ty
6
1
1
Installation_MECA.fm  32 ページ  ２００３年５月１５日　木曜日　午後７時１６分 
						

							33
Installation Manual
■Assembly
1Assemble the optional stand or wall-mounting fixture.
■If you are using a stand, refer to page 42.
■If you are using a wall-mounting fixture, refer to page 46.
2Remove the electronic board from the shipping box.
Remove the joints, then remove the electronic board from the shipping box.
Caution
 When removing the screen unit, grasp the side cover on either side of screen.
Do not grasp the screen film surface, as this may scratch it.
 The shipping box, cushioning material, and other packing material will be necessary if you ever need to 
repackage the electronic board, so do not throw them away.
Board attachment (lower)
Board attachment (upper)
Copy paper roll
Powe r c o r d
Cover (upper)
Cover (lower)
Markers
Screen unit
Printer unitEraserPaper holder ï
·ïAB
Manuals, CD-ROM
Joint Screws and spacers
UB-5310_MECA.book  33 ページ  ２００３年５月１５日　木曜日　午後５時２３分 
						

							34
3Collapse the carton box.
Remove the tape and the staples on 
the unopened side of the carton box, 
then collapse the box.
4Remove the protective plastic bags.
Remove the protective plastic bag 
from the screen unit and printer unit. 
Set those units on the top of collapsed 
shipping box and remove the 
cushions.
Caution
 Touch the screen film surface gently to avoid 
any damage.
5Attach the screen unit to the 
optional stand or wall mounting 
fixture.
■If you are using the stand, refer to 
page 42.
■If you are using the wall mounting 
fixture, refer to page 46.
6Hang the screen unit to the board 
attachment (upper).
Hold the side covers of the screen unit 
and hang two hooks of the screen unit 
on the left side of the board 
attachment (upper).
Shift the screen unit to the left until it 
stops. Confirm the left hook is inserted 
into the groove of the board 
attachment (upper).
 When hanging the screen unit, set the board 
attachment frame at the lowest level.
 Be careful not to catch the screen film on the 
board attachment frame.
7Remove the shipping screws.
Remove the lower and upper  shipping 
screws on the folded screen.
Caution
 Remove the lower shipping screw first.
Carton Remove the tape and the staples.
To p
Bottom
Protective 
plastic bag
Screen unit
Cushions Cushions
Cover (left)Board attachment
(upper)
Cover (right)Board 
attachment
Frame
UB-5310_MECA.book  34 ページ  ２００３年５月１５日　木曜日　午後５時２３分 
						

							35
Installation Manual
8Extend the screen unit.
Open the center and right panels of 
the screen unit as shown below and 
remove the cushion.
Caution
 Touch the screen film surface gently when 
opening the screen unit. 
9Unlock the hook.
Unlock the hook connected to the 
center and right panels. Extend the 
screen unit and remove the cushion 
behind the screen.
 
Caution
 Touch the screen film surface gently when 
opening the screen unit. 
10Extend the screen unit.
Hang the right hook of the screen unit 
on the board attachment (upper).
Caution
 Touch the screen film surface gently when 
opening the screen unit. 
11Fix the screen unit.
Fix the left, center and right panels 
with the screws and spacers supplied. 
To tighten the screws, use the 
supplied wrench.
Cushion
Lift the right 
panel slightly 
and extend it.Hook
Cushion
Right hook
SpacersScrews (short)
Screws 
(long)
Washe r Wa she r
UB-5310_MECA.book  35 ページ  ２００３年５月１５日　木曜日　午後５時２３分 
						

							36
■Adjusting the level of the screen 
unit (Step 12–15: only for use of 
the optional stand)
At the lowest level of the board attachment frame, 
the printer cannot be installed. Raise the level of 
the screen unit as follows.
 Please lock the casters when you adjustment the 
screen height. Refer to Operating Instructions 
page 5.
12Loosen the height adjustment 
handles on the board attachment 
frame.
13Hang the step frame on the center 
of the reinforce pipe.
Hold the center of the board attachment 
(lower) of the board attachment frame from 
the back of the screen unit and lift the board 
attachment frame by stepping on the step 
frame to lift the board attachment frame 
smoothly.
When lifting the board attachment frame, be 
sure to hold the handle in the center of the 
frame.
14Hang the screen in the desired slots 
of the slide plates and tighten the 
handles.
Caution
The screen can be adjusted at 4 levels.
 The lowest level of the board attachment frame 
is designed for the installation of the screen, so 
the printer cannot be attached at that level. Use 
the electronic board at upper 3 levels.
 Make sure to tighten the height adjustment 
handles firmly after adjusting the level of the 
screen.
 Confirm both of the screws are hung in the same 
height slots.
 Store the step frame by hanging it on the board 
attachment (upper).
Height 
adjustment 
handlesHeight 
adjustment
handles
Board 
attachment 
(lower)
Reinforce pipe
Step frame
Slot for installing 
the screen
(The printer cannot
be attached at this 
position.) Slots for 
height 
adjustment
Step frame
UB-5310_MECA.book  36 ページ  ２００３年５月１５日　木曜日　午後５時２３分 
						

							37
Installation Manual
15After hanging the screen, fix the 
stopper screw (left side only).
This prevents the user from adjusting 
the screen height at the lowest level by 
mistake.
16Attach the printer unit.
Hang the hooks of the printer unit on 
the square holes of the board 
attachment (lower).
Caution
• When attaching the printer unit, make sure the  cable is not caught between the metallic frame 
and the printer unit.
17Tighten the screws for the printer 
unit.
Use four screws for the optional stand 
and two screws for the wall mounting.
■ Optional stand
■ Wall-mounting
Stopper screw
[Screw (short)
See page 42.]
Board attachment 
(lower)
Printer unit
Installation_MECA.fm  37 ページ  ２００３年５月１６日　金曜日　午前１０時２４分 
						

							38
18Connect the cables (2) to the screen 
panel connectors.
19Remove the folding support screw 
on the front side of the screen unit, 
then store the folding support on 
the back side.
20Attach the cover (upper).
Hook the cover with the projections on 
both sides, then cover the top of the 
board attachment (upper).
21Store the shipping screws for fixing 
the screen panels, the screw for the 
folding frame and the wrench in the 
tool box on the top of the printer 
unit.
Folding support screw
Folding support
Board attachment (upper)
Cover (upper)
Tool box
Shipping screwsWrench
Folding support screw
UB-5310_MECA.book  38 ページ  ２００３年５月１５日　木曜日　午後５時２３分 
						

							39
Installation Manual
22Attach the cover (lower).
(1) Push the cover in the direction of the arrow until it clicks.
(2) Fix the cover with the wing bolt.
23Attach the power cord.
Securely fit the supplied power cord 
into the AC inlet on the printer unit.
24Attach the paper holders.
Attach the paper holders to the printer 
section in numerical order of the 
arrows (1), (2), (3) and (4).
25Attach the rear cover. (only for use 
of the optional stand)
• After peeling off the cover sheets of the  adhesive tapes, attach the rear cover to the 
board attachments (upper/lower) while 
matching the top edges of them. Then install 
the rivets.
 The rear cover and rivets are supplied with  the optional stand.
26Wipe the screen film surface.
Soak a soft cloth with water, wring 
well, and wipe the screen film surface.
Caution
• Do not wipe the screen film surface with paint  thinner, benzene, or cleaners that contain 
abrasives. Doing so may cause discoloration.
 Do not wipe the screen film surface with a dry  cloth. Doing so may create static electricity.
27Check the operations.
Refer to “Electronic Board Operations 
Check” on page 40.
AC inlet Power cord
Paper holder   
Install first.A
Hole for B
Hole for B
Hole for A
Paper holder 
Install second on top of first.B
Adhesive 
tape
Rivets
Installation_MECA.fm  39 ページ  ２００３年５月１５日　木曜日　午後７時１８分 
						

							40
Electronic Board Operations Check
After assembling the electronic board, perform the procedures presented in the following table to make sure it 
functions properly.
Step
Points to Check
SymptomSolutions
1Turn on the power switch.
“ ” flashes after “ ” lights up.(Normal operation)
(If not) Check power cord and  
cables.
(See step 23 on page 39 
and step 18 on page 38.)
2Open the printer door and load the 
copy paper, then close the printer door.
 loading the copy paper procedure 
(refer to the Operating Instructions 
page 10)“ ” lights up after the copy paper 
is fed and automatically cut. (Normal operation)
(If not) Check the condition of 
printer door or copy 
paper roll.
3Press .Screen is fed. (Normal operation)
The screen film surface is not fed 
smoothly.Contact the store or 
dealer from which the 
unit was purchased.
There are strange noises.
4Use the accessory marker to draw 
a large   filling the entire 
copyable area of the screen film 
surface.
 Copying area (refer to the 
Operating Instructions page 7)
Press  twice.
Press .“ ” lights up and three copies 
are made.(Normal operation)
Three copies are not made. Contact the store or 
dealer from which the 
unit was purchased. The entire readable area is not 
printed.
There are strange noises or 
paper jams during the copying 
process.
5Press   to move the screen film 
surface.
Write letters, etc. with the marker.
Press  once.
Press .The Contrast indicator light is 
turned on and copy is made.(Normal operation)
The Contrast indicator light is 
not turned on.Contact the store or 
dealer from which the 
unit was purchased.
The image is not copied properly.
There are strange markings on 
the copy sheet (e.g., stripes or 
lines).
6Press  once.The Contrast indicator light is 
not turned off.Contact the store or 
dealer from which the 
unit was purchased.
7Press .Two screens are not copied 
properly.Contact the store or 
dealer from which the 
unit was purchased.
UB-5310_MECA.book  40 ページ  ２００３年５月１５日　木曜日　午後５時２３分