Panasonic DLP Based Projector PT-D7700U PT-DW7000U Operating Instructions

							DLPTMBased Projector  Commercial Use
Operating Instructions
Read these instructions completely before operating this unit.
TQBJ 0146-1
POWERON OFFRGB1RGB2AUX
MENU
STD
LENSOSD1
4
72
5
83
6
9
0
NEXTUSERLIGHTID ALLASPECTID SETProjectorComputerNumetric
BRIGHTCONTRAST ON SCREENSYSTEMSELFUNC1D.ZOOM
ENTERPA G E  UP
PA G E  DOWN
VIDEOSHUTS-VIDEOFREEZESHUTTER
AUTO
SETUP
LASER ON/OFF
Model No. PT-D7700U
PT-DW7000U 
						

							2
Dear Panasonic Customer:
This instruction booklet provides all the necessary operating information that you might require. We hope it will help
you to get the most performance out of your new product, and that you will be pleased with your Panasonic DLPTM
based projector.
The serial number of your product may be found on its back. You should note it in the space provided below and
retain this booklet in case service is required.
Model number: PT-D7700U / PT-DW7000U
Serial number:
IMPORTANT SAFETY NOTICE
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS PRODUCT TO RAIN OR MOISTURE.
WARNING
RISK OF ELECTRIC
SHOCK. DO NOT OPEN
MISE EN GARDE-
WARNUNG-
RISQUE DE CHOC ÉLECTRIQUE.
NE PAS OUVRIR.
ZUR VERMEIDUNG EINES ELEKTRISCHEN
SCHLAGES GERÄT NICHT ÖFFNEN.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert
the user to the presence of uninsulated “dangerous voltage” within the Products enclosure
that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the product.
CAUTION: This equipment is equipped with a three-pin
grounding-type power plug. Do not remove the
grounding pin on the power plug. This plug will
only fit a grounding-type power outlet. This is a
safety feature. If you are unable to insert the plug
into the outlet, contact an electrician. Do not
defeat the purpose of the grounding plug.
Do not remove 
						

							3
WARNING: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
–   Reorient or relocate the receiving antenna.
–   Increase the separation between the equipment and receiver.
–   Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
–   
Consult the dealer or an experienced radio/TV technician for help.
FCC CAUTION: To assure continued compliance, use only shielded interface cables when
connecting to computer or peripheral devices. Any unauthorized changes or
modifications to this equipment could void the user’s authority to operate.
WARNING: 
Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer/Data
Processing Equipment, ANSI/NFPA 75.
NOTICE: This product has a High Intensity Discharge (HID) lamp that contains a small amount
of mercury. It also contains lead in some components. Disposal of these materials
may be regulated in your community due to environmental considerations.  For
disposal or recycling information please contact your local authorities, or the
Electronics Industries Alliance: 
Declaration of Conformity
Model Number: PT-D7700U / PT-DW7000U
Trade Name: Panasonic
Responsible Party: Matsushita Electric Corporation of America
One Panasonic Way, Secaucus, NJ 07094
Telephone Number: 1-800-524-1448 or 1-800-526-6610
Email: [email protected]
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference receiver, including interference that may
cause undesired operation. 
						

							4
IMPORTANT SAFETY NOTICE ..................................2
Precautions with regard to safety ............................5
Accessories ................................................................7
Precautions on handling ...........................................8
Examples of system expansion ................................9
Name and function of parts.....................................10
Remote control ................................................................10
Front and side of the projector ........................................12
Rear view of the main unit ...............................................13
Controls on rear panel .....................................................13
Side-mounted connection terminals ................................14
Using the remote control unit .................................15Loading dry cells .............................................................15
Effective range of remote control operation ....................15
Setting projector ID number to remote control ................16
Using the remote control as a PC mouse........................17
Using a wired remote control...........................................17
Installation ................................................................18Adjusting the leveling feet ...............................................18
Projection scheme ...........................................................18
Installation geometry .......................................................18
Projection distances by the type of projection lenses (optional)..19
Connection ...............................................................24Before starting connection...............................................24
Example of connecting with VIDEO devices ...................25
Example of connecting with personal computers ............26
Example of connecting with the signal selector...............27
Installation of input module (optional) ...................28Installing the input module...............................................28
Connecting signals to the input module ..........................30
Connecting the signal to the analog RGB signal input module..31
Connecting the signal to the video signal input module ..32
Connecting the signal to the serial digital signal input module..34
Connecting signals to the DVI signal input module .........37
How to install and remove the projection lens (optional)..........38How to install the projection lens .....................................38
How to remove the projection lens ..................................38
Projection..................................................................39Powering up the projector ...............................................39
Making adjustment and selection ....................................39
Powering off the projector ...............................................40
How to adjust the lens .............................................41How to adjust the lens focus, lens zoom and lens shift (optical shift)..41
Adjustment range after lens position (optical shift)..........41
How to adjust the lens for addressing unevenness of focusing..42
Automatic adjustment (AUTO SETUP) ...................43
Registration of input signal data ............................44
Registration of new data..................................................44
Renaming the registered signals .....................................44
Clearing the data of registered signals
...............................45
Sub memory ....................................................................46
Using the FREEZE function ....................................48
Using the SHUTTER function..................................48
Using the digital zoom (– D.ZOOM +) function ...............48
On-screen menus .....................................................49
Structure of menu screens ..............................................49
Basic operations on menu screen ...................................50
Returning to the previous screen ....................................50
Menu items shown in gray characters .............................50
Menu items setting ..........................................................50
Resetting to the factory default........................................50
Adjusting the picture ...............................................51Switching the picture mode .............................................51
Adjusting Contrast / Bright / Color / Tint ..........................52
Registering the picture mode settings as presettings......53
DYNAMIC IRIS setting ....................................................54
Adjusting the color temperature ......................................55
Sharpness / Gamma / Noise reduction ...........................56
To display pictures complying with the sRGB standard ..56
Adjusting the position .............................................57Shift adjustment...............................................................57
Size adjustment ...............................................................58
Clock phase adjustment ..................................................59
Keystone distortion correction .........................................60
How to use ADVANCED MENU ...............................61DIGITAL CINEMA REALITY ...........................................61
FORMAT (To input BETACAM with YCbCr 480i) ...........61
Blanking adjustment ........................................................62
Adjusting the input resolution ..........................................63
Adjusting the clamp position............................................64
Edge blending adjustment ...............................................65
How to switch the input impedance (signal level) 
of the synchronization signal ...........................................66
Raster position ................................................................67
Changing the display language ..............................68
How to change the system format..........................69
How to use RGB REALITY mode ............................70
Option settings .........................................................71
ID number setting ............................................................71
Installation Setting ...........................................................72
Lamp select .....................................................................73
Lamp power.....................................................................73
RS232C SETTING (Procedure of setting communication conditions)..74
Position of on-screen indications.....................................74
System information..........................................................74
Adjusting color matching .................................................75
Adjusting the color matching using a colorimeter ............76
Video setting....................................................................77
Automatic adjustment ......................................................77
Output resolution (D7700U only) .....................................78
Auto signal.......................................................................78
Fan control ......................................................................78
P IN P ..............................................................................79
Setting FUNC1 ................................................................80
Password.........................................................................80
How to change the signal for the 
ET-MD95VM2 (optional) ...........................................81
Using the serial terminals .......................................82
Examples of connection  .................................................82
Pin assignments and signal names .................................82
Communication conditions (Factory setting) ...................82
Basic format ....................................................................82
Control commands ..........................................................83
Cable specifications ........................................................83
Using the REMOTE 2 terminal ................................84
Displaying the internal test pattern ........................85
Cycle of displayed internal test patterns..........................85
RS-422 control functions.........................................85
Setting the security ..................................................86
Setting the password .......................................................86
Changing the password...................................................87
Setting the text ................................................................87
Changing the text ............................................................87
How to use CP OPTION ...........................................88Setting the on-screen indication function ........................88
Setting the system format................................................89
How to use network module (optional) ..................90Initial setting of network module ......................................91
Accessing from the Web browser....................................92
Returning the network module setting back to the factory setting..97
Indication of monitor lamp ......................................98
Cleaning and replacement of air filter ....................99
Procedure of cleaning .....................................................99
Replacement of lamp unit .....................................100Timing of lamp unit replacement ...................................100
Procedure of lamp unit replacement .............................101
Before asking for service ......................................103
Specifications .........................................................104
Appendix .................................................................106
Outside dimensions ...............................................107
Français Information..............................................108
Contents 
						

							5
Precautions with regard to safety
WARNING
If a problem occurs (such as no image) or if you notice smoke or a strange smell coming
from the projector, turn off the power and disconnect the power cord from the wall outlet.
• Do not continue to use the projector in such cases, otherwise fire or electric shocks could result.
• Check that no more smoke is coming out, and then contact an Authorized  Service Center for repairs.
• Do not attempt to repair the projector yourself, as this can be dangerous.
Do not install this projector in a place which is not strong enough to take the full weight
of the projector.
• If the installation location is not strong enough, it may fall down or tip over,  and severe injury or damage could
result.
• Installation work (such as ceiling suspension) should only be carried out  by a qualified technician.
• If installation is not carried out correctly, there is the danger that injury or  electric shocks may occur.
If foreign objects or water get inside the projector, or if the projector is dropped or the
cabinet is broken, turn off the power and disconnect the power cord from the wall outlet.
• Continued use of the projector in this condition may result in fire or electric shocks.
• Contact an Authorized Service Center for repairs.
Do not cover the air filter, the air inlet and exhaust vents.
• Doing so may cause the projector to overheat, which can cause fire or damage to the projector.
Do not overload the wall outlet.
• If the power supply is overloaded (for example, by using too many adapters), overheating may occur and fire
may result.
Do not remove the cover or modify it in any way.
• High voltages which can cause fire or electric shocks are present inside the projector.
• For any inspection, adjustment and repair work, please contact an Authorized Service Center.
Clean the power cord plug regularly to prevent it from becoming covered in dust.
• If dust builds up on the power cord plug, the resulting humidity can damage the insulation, which could result in
fire. Pull the power cord out from the wall outlet and wipe it with a dry cloth.
• If not using the projector for an extended period of time, pull the power cord plug out from the wall outlet.
Do not do anything that might damage the power cord or the power cord plug.
• Do not damage the power cord, make any modifications to it, place it near any hot objects, bend it excessively,
twist it, pull it, place heavy objects on top of it or wrap it into a bundle.
• If the power cord is used while damaged, electric Shocks, short-circuits or fire may result.
• Ask an Authorized Service Center to carry out any repairs to the power cord that might be necessary.
Do not handle the power cord plug with wet hands.
• Failure to observe this may result in electric shocks.
Insert the power cord plug securely into the wall outlet.
• If the plug is not inserted correctly, electric shocks or overheating could result.
• Do not use plugs which are damaged or wall outlets which are coming loose from the wall. 
Do not place the projector on top of surfaces which are unstable.
• If the projector is placed on top of a surface which is sloped or unstable, it may fall down or tip over, and injury or
damage could result.
Do not place the projector into water or let it become wet.
• Failure to observe this may result in fire or electric shocks.
Do not disassemble the lamp unit.
• If the lamp section breaks, it may cause injury. 
						

							6
Precautions with regard to safety
Do not place liquid containers on top of the projector.
• If water spills onto the projector or gets inside it, fire or electric shocks could result.
• If any water gets inside the projector, contact an Authorized Service Center. 
Do not insert any foreign objects into the projector.
• Do not insert any metal objects or flammable objects into the projector or drop them onto the projector, as doing
so can result in fire or electric shocks.
After removing the battery from remote control unit, keep it away from the reach of children.
• The battery can cause death by suffocation if swallowed.
• If the battery is swallowed, seek medical advice immediately.
Do not allow the + and - terminals of the battery to come into contact with metallic
objects such as necklaces or hairpins.
• Failure to observe this may cause the battery to leak, overheat, explode or catch fire.
• Store the battery in a plastic bag and keep it away from metallic objects.
Insulate the battery using tape or similar before disposal.
• If the battery comes into contact with metallic objects or other batteries, it may catch fire or explode.
Replacement of the lamp unit should only be carried out by a qualified technician.
• The lamp unit has high internal pressure. If improperly handled, explosion might result.
• The lamp unit can easily become damaged if struck against hard objects or dropped, and injury or malfunctions
may result.
Do not set up the projector in humid or dusty places or in places where the projector may
come into contact with smoke or steam.
• Using the projector under such conditions may result in fire or electric shocks.
When disconnecting the power cord, hold the plug, not the cord.
• If the power cord itself is pulled, the cord will become damaged, and fire, short-circuits or serious electric shocks
may result.
Always disconnect all cables before moving the projector.
• Moving the projector with cables still attached can damage the cables, which could cause fire or electric shocks
to occur.
Do not place any heavy objects on top of the projector.
• Failure to observe this may cause the projector to become unbalanced and fall, which could result in damage or injury.
Do not short-circuit, heat or disassemble the battery or place it into water or fire.
• Failure to observe this may cause the battery to overheat, leak, explode or catch fire, and burns or other injury
may result.
When inserting the battery, make sure the polarities (+ and -) are correct.
• If the battery is inserted incorrectly, it may explode or leak, and fire, injury or contamination of the battery
compartment and surrounding area may result.
Use only the Specified battery.
• If an incorrect battery is used, it may explode or leak, and fire, injury or contamination of the battery
compartment and surrounding area may result close to this port, otherwise burns or damage could result.
Caution 
						

							7
Accessories
Check that all of the accessories shown below have been included with your projector.
Remote control unit
[N2QAGB000024 x 1]
POWERON OFF
RGB1RGB2AUX
MENU
STD
LENSOSD1
4
72
5
83
6
9
0
NEXTUSERLIGHTID ALLASPECTID SETProjectorComputerNumetric
BRIGHTCONTRAST ON SCREEN
SYSTEMSELFUNC1D.ZOOM
ENTER
PAGE UP
PAGE DOWN
VIDEOSHUTS-VIDEOFREEZE
SHUTTER
AUTO
SETUP
LASER ON/OFF
Power cord
[K2CF3EH00001 x 1]Wired cable for remote control
[15m (493),
K1EA03NA0001 x 1]
Battery for remote control
unit (AA)
[R03NPA/2ST x 1]
Do not look into the lens while the projector is being used.
• Strong light is emitted from the projector’s lens. If you look directly into this light, it can hurt and damage your eyes.
Do not bring your hands or other objects close to the air outlet port.
• Heated air comes out of the air outlet port. Do not bring your hands or face, or objects which cannot withstand heat.
Do not use the old lamp unit.
• The lamp section may break.
Replacement of the lamp unit should only be carried out after it has completely cooled
off, otherwise burns may result.
Disconnect the power cord plug from the wall outlet as a safety precaution before
carrying out any cleaning.
• Electric shocks can result if this is not done.
Ask an Authorized Service Center to clean inside the projector at least once a year.
• If dust is left to build up inside the projector without being cleaned out, it can result in fire or problems with
operation.
• It is a good idea to clean the inside of the projector before the season for humid weather arrives. Ask your
nearest Authorized Service Center to clean the projector when required. Please discuss with the Authorized
Service Center regarding cleaning costs.
Do not reach for the openings beside the optical lens, during horizontal or vertical
movements of the lens there is a injury hazard.
An effort to keep our environment clean, Please bring the non repairable unit your Dealer
or a Recycling Company. 
						

							8
Precautions on handling
Precautions on transport
The projection lens is susceptible to vibrations and
impacts. Be sure to always remove the lens during
transport.
Precautions on installation
Be sure to observe the following precautions when
installing the product.
Avoid installing the product in a place
exposed to vibrations or impacts
.
If the projector is installed in a place where
vibrations are transmitted from a source of
driving power and others or mounted in a car or
a vessel, vibrations or impacts may be
transmitted to the product to damage the internal
parts, causing failure.  Install the product in a
place free from vibrations and impacts.
Do not install the projector near high-
voltage power lines or power sources.
The product may be exposed to interference if it
is installed in the vicinity of high-voltage electrical
power lines or power sources.
Do not place the projector on a vinyl
sheet or carpet.
If a vinyl sheet sucked up and blocks the air filter
intake port, the internal temperature of the
projector may increase, which triggers the
protection circuit, turning off the power.
Be sure to ask a specialized
technician when to install the
product to a ceiling.
If the product is to be installed hanging from the
ceiling, purchase an optional hanging attachment
(for high ceiling: Model No. ET-PKD75) (for low
ceiling: Model No. ET-PKD75S) and call a
specialized technician for installation.
Do not place the projector over 2 700 m
(8881.5) above sea level. When using it
over 1 400 m (4605.3) above sea level, set
the “Fan Control”, described on page 78,
to “HIGHLAND”.
Otherwise the life of the product may be shortened.
Precautions on use
To view clear images:
• The audience cannot enjoy high-contrast and
clear images if outside light or the illumination
interferes the screen surface.Draw window
curtains or blinds, turn off the lightings near the
screen or take other proper measures.
• In rare cases, wafture can occur on the screen
affected by the warm air from the exhaust port
depending on the environment.
Do not touch the surface of the
projection lens with bare hand.
If fingerprints or stains are left on the projection
lens surface, they are magnified and projected
on the screen. Keep your hands away from the
lens. Cover the lens with the supplied lens cap
when the projector is not used.
Screen
If the screen has stains, flaws or discoloration,
clear images cannot be viewed.  When handling
the screen, be careful not to apply volatile
substances or leave flaws or stains on the screen.
Lamp
A mercury lamp with high internal pressure is used
for the light source of this product.  A high-pressure
mercury lamp has the following characteristics:
• It may burst with a loud sound or end its life
cycle by not illuminating because of given
impacts, flaws, or deterioration due to used
hours.
• The life cycle of a mercury lamp varies according
to the individual difference or conditions of use.
In particular, turning the power on and off
frequently and/or repeatedly will greatly affect
the life cycle.
• In rare cases, it may burst shortly after the first
lighting.
• The possibility of burst increases when the lamp
is used beyond the replacement time.
Disposal
To discard the product, call the dealer or a specialized
dealer.
Cleaning and maintenance
Be sure to remove the power cord plug from the receptacle before cleaning.
Use soft and dry cloth to clean the cabinet
If stains are hard to remove, use a cloth dampened with a kitchen detergent solution (neutral) and squeezed
to wipe the cabinet and finish with a dry cloth.  If a chemical wipe is used, follow its instructions.
Do not clean the lens surface with fuzzy or dusty cloth.
If dust adheres to the lens, it will be magnified and projected on the screen.
Use a soft and clean cloth to wipe off dust. 
						

							9
The projector is provided with a number of terminals and optional accessories to enable various system expansions.
Both input and output are provided to all terminals on the main unit.
The following are some examples of system expansion:
Examples of system expansion
System 1
Stacking two projectors with the
stacking brackets can double the
picture brightness.
System 3
PC equipped with a DVI-D input module (an
optional item) can be attached to the
projector for computer image viewing
(Realization of high-resolution picture.)
System 2
The optional high- or low-ceiling mount
bracket flexibly fits the projector in
individual site conditions.
System 4
Connection of a signal selector enables to
feed a variety of video sources to the
projector.
OFFOFFPOWERONINPUT  SE
LECT1
2
3
456VP
ON/OFFSignal Selector TW-SWS
Digital broadcasting tuner 
or DVD playerControl PC
Signal selector
(Option)Video deck 
						

							10
Name and function of parts 
< When the operation mode selector  is
set to Projector >
Remote control operation indicator lamp
The lamp flashes when any remote control button
is pressed.
POWER ON button (page 39)
Turns on the power if the MAIN POWER has been
put to the “l” position.
POWER OFF button (page 40)
Turns off the power if the MAIN POWER has been
put to the “l” position.
AUTO SET UP button (page 43)
Pressing this button while projecting an image
automatically corrects the picture positioning on the
screen.  While the auto setup feature is active, a
message “PROGRESS...” appears on the screen.
Input selector (RGB1, RGB2, AUX, VIDEO, 
S-VIDEO) button 
Use to toggle through the RGB1, RGB2, AUX
(module input), VIDEO and S-VIDEO input ports.
SHUTTER button (page 48)
Press this button to black out the image
temporarily.
MENU button (page 50)
Displays and clears the Main Menu.  It can also
return to the previous screen when the menu is
displayed.
FREEZE button (page 48)
Press this button to freeze the image temporarily.
Arrow  buttons (page 50)
Use these buttons to select an item on the menu
screen, change setting and adjust the level.
Also use them to enter the “SECURITY” password.
ENTER button (page 50)
Press this button to enter your menu selection or to
run function.
ON SCREEN button
This button turns on and off the on-screen
indication function.
Standard (STD) button (page 50)
Press this button to restore the default factory setting.
SYSTEM SELECTOR button (page 69)
System switching can be done.
Function 1 (FUNC1) button (page 80)
This button can control the functions set in
“FUNC1” of the “Option” screen from Main Menu.
Digital Zoom (- D.ZOOM +) buttons (page 48)
Any portion of the picture can be zoomed in.
LENS button (page 41)
Switches to the mode of projection lens
adjustment.
CONTRAST button (page 52)
Switches to the mode of image contrast
adjustment.
BRIGHT button (page 52)
Switches to the mode of black level adjustment.
NEXT button
When multiple signal selectors are connected to
the main unit in the system, this button specifies
the second signal selector or beyond. With the ID
set button pressed, every press on the button will
change the value in the ten’s place.
ASPECT button
Switches the image aspect ratio to 4:3, 16:9.
Remote control
POWERON OFF
RGB1RGB2AUX
MENU
STD
LENSOSD1
4
72
5
83
6
9
0
NEXTUSERLIGHTID ALLASPECTID SETProjectorComputerNumetric
BRIGHTCONTRAST ON SCREEN
SYSTEMSELFUNC1D.ZOOM
ENTER
PA G E  UP
PAGE DOWN
VIDEOSHUTS-VIDEOFREEZE
SHUTTER
AUTO
SETUP
LASER ON/OFF