Panasonic DLP Based Projector PT-D5600U PT-D5600UL PT-DW5000U PT-DW5000UL Operating Instructions

41
Indication of lamp monitor
This projector is equipped with 3 indicators to show when a lamp needs replacement or there is an abnormal
internal temperature. These lamps flash or light up to indicate a problem.
Turn the power off and follow the steps below.
Temperature monitor 
(TEMP) indicator Lamp 1 monitor (LAMP 1) Lamp 2 monitor (LAMP 2) Power indicator
• To solve any problems that the TEMP and LAMP monitor show, first turn the power off by
following the steps on pages 23, 24.
• If the power...

42
Cleaning and replacement of air filter
If too much dust accumulates on the air filter, [AIR FILTER] appears at the lower left of the screen, and the
temperature monitor (TEMP) will blink once. If even more dust is allowed to accumulate, the temperature inside the
main unit will rise, the temperature monitor (TEMP) will blink twice, and the power is turned off.
Clean the air filter section once every 100 hours or so as a guideline depending on the location of projector
operation.
It appears only for 30...

43
Replacing the lamp unit
Precautions on lamp unit replacement
Remove the power plug and confirm that the surroundings of the lamp unit have cooled off.
Be careful when handling a light source lamp. The lamp unit has high internal pressure. If improperly handled,
explosion might result.
A used lamp unit may burst if it is handled violently.
For disposition of used lamps, request an industrial waste disposal contractor.
Do not reset the cumulative time, except when the lamp unit has been replaced with a...

44
Replacing the lamp unit
Lamp unit replacement steps
• After 1 500 hours (4 000 hours when long life lamp units are used) of operating the same lamp, it
is only possible to operate the unit for approximately 10 minutes. Steps  to  must be
completed within 10 minutes.Attention
Turn the power off by following the steps on page 24, remove the power plug and
confirm that the surroundings of the lamp unit have cooled off.
Check that the fan has stopped running.
Have a Phillips screwdriver ready ahead of...

45
Insert the power cord plug into the wall outlet and then
press the MAIN POWER switch.
Press the “ I ” button so that a picture is projected onto
the screen.
Press the “MENU” button to display the MAIN MENU
screen, and then press the  and  buttons to move
the cursor to select “OPTION2”.
Press the “ENTER” button to display the “OPTION2”
screen, and select “SYSTEM INFORMATION” with the 
and buttons.
Press the “ENTER” button.
The SYSTEM INFORMATION screen will be displayed.
Press and hold the “ENTER”...

46
Using Web Browser Control 
Accessing from the Web browser
Start the web browser on your PC, then
enter the IP address which was set in
the projector.
Enter “user1” in the user name field,
then enter the password in the
password field.
The default setting is “panasonic” (all lower case). If
you have changed the password, enter the new
password here. 
The host name set in the projector is displayed in
the “Realm” field.
Click [OK]. 
The Basic Control page is displayed.
Password change page
Click [Change...

47
Basic control page
This page is the first page displayed when the projector is accessed through a web browser.
To move from another page, click [Projector control], then [Basic control]. 
E-mail set up button
Click this item, and an E-mail setting page appears.
Monitor information button
Click this item, and the status of the projector is displayed.
Detail control page
Click [Projector control], then [Detail control] to display the Detail control page.
Pressing these buttons controls the projector and...

48
Using Web Browser Control 
Error information page
When  is displayed on the status information screen, click it to display the error details.
• Depending on the nature of the error, the projector may be placed in the standby mode for its own
protection.Note
OK: Normal operation
FAILED: Occurrence of trouble
Monitor information page
Click [Projector control], then [Status information] to display the Status information page.
This page displays the projector statuses established for the items shown...

49
When [FAILED] has appeared for an item
Parameter
MAIN CPU BUS
FAN
OPTICS MODULE
TEMPERATURE
INPUT AIR TEMPERATURE
AROUND LAMP
TEMPERATURE
LAMP REMAIN TIME
LAMP STATUS
SHUTTER
AIR FILTER
OPTICS MODULE TEMP.SENSOR
INPUT AIR TEMP.SENSOR
AROUND LAMP 
TEMP. SENSOR
BATTERY
AIRFLOW SENSOR
COLOR WHEEL
Description
Trouble has occurred in the microcomputer circuitry. Consult your dealer.
Trouble has occurred in the fan or its drive circuit. Consult your dealer.
The temperature inside the projector is high. It...

50
Using Web Browser Control 
Enter the E-mail address to which the E-
mail is to be sent when two E-mail
addresses are going to be used. Do not
enter it when the second E-mail address
is not going to be used.
Check these boxes when E-mail is to be
sent periodically to two E-mail
addresses. E-mail will be sent at the
times and on the days checked.
E-mail setup page (Continuing)
Select the conditions for sending E-mail.
ERROR:
an error is detected by self-diagnosis.
LAMP RUNTIME:remaining lamp
service...