Panasonic Digital Imaging System For Copy Functions Dp 6530 Operating Instructions

1
2
3
4
5
6
7
8
9
10
11
12
5-3
Single-feed Mode
3
Press the  SADF  key.
 Select other copy modes as required.
4
Place an original.  Page 2-9
- The original is automatically pulled in and the screen changes
as shown on the right.
- If there are more originals, set them in the same way. (The
same operation is carried out whether or not you press the
YES  key.)
5
After all originals have been fed through the
reversing automatic document feeder, press the
FINISHED  key.
- Copying begins.
1
Place paper in the...

1
2
3
4
5
6
7
8
9
10
11
12
5-4USING THE SPECIAL FUNCTIONS
3
Press the  PROGRAM  key to enter the program
menu, and press the  MIXED ORIGINAL SIZES
key.
2. MIXED-SIZED ORIGINALS
 Select other copy modes as required.
6
Press the  START  key.
2
Adjust the slide to the widest paper size, and align
the originals against the left front side.
- Place the originals face up.
When placing the different-sized originals in the reversing automatic document feeder, you can make
copies by setting MIXED-SIZED...

1
2
3
4
5
6
7
8
9
10
11
12
5-5
2
Press the  PROGRAM  key to enter the program
menu, and press the  JOB MEMORY  key.
3. JOB MEMORY
Storing a Combination of Copy Job Settings
You can store and recall a combination of frequently used copy jobs at anytime.
Up to four such combinations of jobs can be stored.
* You cannot delete the copy modes that have already been stored in the memory, but you can rewrite
new jobs on the memory key in which some copy modes have already been stored.
3
Press the  MEMORY  key....

1
2
3
4
5
6
7
8
9
10
11
12
5-6USING THE SPECIAL FUNCTIONS
4
Press the  RECALL  key.
3. JOB MEMORY (Cont.)
2
Place the original(s).  Page 2-9
5
Press the Memory Number key where the desired
combination of copy job settings are stored.
- Memory Number keys where copy jobs have been already
stored are shown in a half-tone shaded pattern.
3
Press the  PROGRAM  key to enter the program
menu, and press the  JOB MEMORY  key.
6
Press the  START  key.
- Copies will be made in the recalled copy jobs.
Recalling a...

1
2
3
4
5
6
7
8
9
10
11
12
5-7
To confirm the copy modes stored in the Memory Number key,
perform steps 3 to 5 on the previous page, then press the
SETTINGS  key.
Confirming Stored Copy Jobs
- The screen on the right is an example of jobs that have been
stored in “MEMORY 2”. 

1
2
3
4
5
6
7
8
9
10
11
12
5-8USING THE SPECIAL FUNCTIONS
MAX
4. BYPASS COPYING
When you want to make copies on thick paper, OHP film, tab paper, tracing paper, sticker labels, use the
sheet bypass. (Only thick and tab papers can be set in the drawer. 
 Page 2-7)
If the desired size of paper (standard size) is not set in any of the drawers, or if you want to make copies
on non-standard size, make bypass copies.
The modes below are available even in bypass copying if the paper size is specified:
-...

1
2
3
4
5
6
7
8
9
10
11
12
5-9
4
After selecting the paper type corresponding to the
type of the paper that has been set, press the SET
key.
- When selecting OHP film, the hole punch mode and the
staple mode cannot be used.
If you select the paper type not corresponding to the type of
the paper that has been set, it may cause a problem such as
a paper jam, significant image deterioration, etc.
 Select other copy modes as required.
5
Press the  START  key.
3
If the paper other than standard type has been...

1
2
3
4
5
6
7
8
9
10
11
12
5-10USING THE SPECIAL FUNCTIONS
4. BYPASS COPYING (cont.)
Bypass Copying on Standard Size Paper
1
perform steps 1 to 2 on pages 5-8, 5-9.
-Set the OTHER size key as necessary.  Page 5-14
2
Press the key of the same type as the paper that
has been set.
-Non-standard size paper  Page 5-11
If the paper that has been set is a standard size other than LD,
LG, LT or ST, you will select the  OTHER  key in step 2. In this
case, you need to make the  OTHER  key recognize the same
size...

12
3
4
5
6
78
9
10
11
12
5-11
2
Press the  NON-STANDARD  key.
1
Perform steps 1 to 3 on page 5-10.
The size of non-standard paper is within the following ranges:
  Length: 100 - 297mm (3.94” - 11.69”)   Width: 148 - 432mm (5.83” - 17.01”)
3
Key in each dimension (length and width), or recall
the data stored in the MEMORY. Then press the
lower  SET  key.
- When using the digital keys to key in the size: Key in the length and press the upper  SET  key. Similarly,set the value for the width.
- Press the...

1
2
3
4
5
6
7
8
9
10
11
12
5-12USING THE SPECIAL FUNCTIONS
3
Press the desired Memory Number key.
- When the paper size is ‘0mm’, the selected Memory
Number key is vacant.
- When the paper size is displayed, a non-standard size is
already stored in the selected Memory Number key. To
delete the settings, perform step 4. New settings will be
rewritten and stored on that Memory Number key.
Storing a Non-Standard Size in the MEMORY
4
Key in each dimension, then press the  MEMORY
key.
- Key in the length and...