Panasonic Digital Hd Video Cassette Recorder Ajhd1800 Operating Instructions

51
Function menus(continued)

The basic input/output settings for the audio signals are set on these menu screens.
1. Audio signal input selection (CH1 - CH4)
2. 
Audio signal input selection (CH5 - CH8)
3. Audio volume control switching, CUE audio 
recording signal selection, and audio monitor mix 
switching
*When the VIDEO input switch is set to 1394, all buttons from A1 IN to A8 IN become 1394 input.
The underlining (__) denotes the factory setting mode.
F1SHIFTF2F3F4F5F6
F1SHIFTF2F3F4F5F6...

52
Function menus (continued)
 (continued)
The underlining (__) denotes the factory setting mode.
Function button/
item Switching 
method SettingCorresponding setup menu 
itemDescription of setting
F1(SHIFT2)
VOLUMEToggle
REC
PB
AU TONo. 141
VO L U M ERefer to the setup menu.
For switching what is to be controlled by the 
audio volume controls. (The levels of all the 
CH1jCH8 channels are controlled.)
F2(SHIFT2)
______
______ ___
F3 (SHIFT2)
RECCUEToggle
CUECH1
CH2
CH3
CH4
CH5
CH6
CH7
CH8
CH1+2
CH3+4...

53
Function menus(continued)

The TC-related settings are performed on these menu screens. Whether the TC is to be superimposed onto the display can
also be set on this screen.
The underlining (__) denotes the factory setting mode.
F1SHIFTF2F3F4F5F6F1SHIFTF2F3F4F5F6
Function button/
item Switching 
method SettingCorresponding setup menu 
itemDescription of setting
F1
TC SRCToggleWhen HD SDI, INT 
SG or 1394 is 
selected:
INT
EXT_L
SLTC
SVITC
No. 507
TC SOURCERefer to the setup menu.
When SD SDI is...

54
Function menus (continued)

A maximum of 60 cue points can be set on these menu
screens.  When “AUTO” has been selected as the 
(PAGE) setting on the AUTO PAGE mode 
menu, up to 10 pages of cue points with 6 cue points on
each page can be managed on a page-by-page basis.  The
60 cue points are indicated using the page number display
and registered point display areas.
  
Cue points cannot be registered, prerolled, etc. if a setting
other than “ENA” has been selected as the setup menu item
No.001...

55
Function menus(continued)
 (continued)
Cue point registration
Turn the ADJUST dial to highlight the point which is to be
registered.  When the  button is pressed, the current
tape position is registered as the cue point. The following
applies depending on the setting for  (PAGE) on the
 menu.
When “MANU” is set:
Operations are performed on the selected page.  Press 
the   button to register the points in succession 
(CUE¢1 > CUE¢2 > ... > CUE¢6) on the selected 
page.  (Any points already registered...

56
Function menus (continued)
 (continued)
Search operations
Turn the ADJUST dial to highlight the desired registered
point.
When the PREROLL button is pressed, the preroll operation
is initiated.  The tape will not be prerolled if no cue points
have been registered.Since the tape is not prerolled even if the PREROLL button
is pressed when the cue point registration mode is
established, be absolutely sure to check that the search
mode is established.
[The time selected by the  menu [ (CU-
ROL) setting,...

57
Function menus(continued)

This enables confirmation of information such as the
warning/hour-meter/UMID.
Verification, deletion of the error log file, retention/call to the
SD memory card can do with the SHIFT picture.
Warning display
When a warning occurs in this VTR, the warning mark (W)
blinks at the top left of the screen.  If   (WARN) is now
pressed, the details of the warning can be checked out on
the LCD monitor.
When more than one warning has occurred, turn the ADJ
dial to scroll through the...

58
Function menus (continued)
 (continued)
The underlining (__) denotes the factory setting mode.
Concerning the setup menu item No.015 (AUTO 
STEP) setting (factory setting: OFF)
Up to 99 warning messages can be saved by the error log
function, and this setup menu item determines what kind of
save processing is to be conducted when this storage
capacity is exceeded.
OFF: 99 messages are set as the upper limit, and no 
further messages of warnings that occur will be 
saved.
ON: 99 messages are saved, and...

59
Function menus(continued)

These enable movement to the menu screens for operations (adjustments, saving data onto or loading it from the internal
memory or SD memory cards) relating to the SYSTEM and SETUP menus.
*The underlining (__) denotes the factory setting mode.
F1SHIFTF2F3F4F5F6F1SHIFTF2F3F4F5F6
Function button/
item Switching 
method SettingCorresponding setup menu 
itemDescription of setting
F1
FILEFiPress
______ For calling the operation menu for saving the 
SYSTEM and SETUP adjustment...

60
Function menus (continued)

The ASSEMBLE editing mode is selected on this menu
screen.
Automatic editing and manual editing
zWhen the editing mode has been selected (the 
button is lighted), automatic editing or manual editing can
be performed even after the ASSEMBLE screen has been
exited.
zAfter the edit IN and OUT points have been registered (the
 and   buttons are lighted), the tape can be
prerolled to an IN point or cued up to an IN or OUT point
even after the ASSEMBLE screen has been exited.
The...