Panasonic Digital Disk Recorders Wj Hd309 Operating Instructions

111
[Screenshot 4]
The cursor moves to the PRESET in STEP 1.
bRotate the jog dial to select a preset position number
for which image is displayed in STEP 1 from the follow-
ing.
1 - 64:Moves to the selected preset number.
--:Does not move to the preset position.
nSelect DWELL in STEP 1 using the arrows button.
[Screenshot 5]
The cursor moves toDWELL in STEP 1.
mRotate the jog dial to select an interval time to go to the
next sequential step from 1 - 30 seconds (in 1 second
intervals).
The sequence step...

112
[Monitor 2] Switcher function of monitor 2
Perform the settings for the switcher function of monitor 2.
8Live Sequence
The settings for Live Sequence are the same as for
Monitor1. Refer to page 110for further information.
8Sequence Timing
The settings for Sequence Timing are the same as for
Monitor1. Refer to page 111for further information.
Notes:
•Select EXT when an external device that can transmit
a sequence signal is connected.
•The sequence changeover I/O (pin no.21) of the
ALARM/CONTROL...

113
Perform the display settings for monitors 1 and 2 connected
to the unit.
OSD Setup
Perform the On Screen Display settings for monitor 1 and
monitor 2 such as the settings of camera titles or the set-
tings of the time display position.
8Camera Title
Perform the settings for the camera title. It is possible to
display a camera title on the monitor 1/monitor 2, and
record it as a part of the recorded image (page 98). Do the
following to set the camera title.
[Screenshot 1]
Start operation from the OSD...

114
3. Move the cursor to OK using the arrows button
and press the SET button. The camera title will
be copied.
•The following characters can be entered for a cam-
era title:
0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P
Q R S T U V W X Y Z a b c d e f g h i j k l m n o p q r
s t u v w x y z À Ä Â Æ Ç É Ì Ñ Ò Ö Ù Ü Ø ß à á â ä
å æ ç è é ê ë ì í î ï ñ ò ó ô ö ù ú ü ø < > = ? ” # & ( )
* + , - . / : ; SP
[Screenshot 4]
The camera title is entered.
bPress the arrows button to move the cursor to OK...

115
8Camera Title Display
Select ON and OFF whether or not to display the camera
title.
ON:Displays the camera title.
OFF:Does not function.
8Alarm Display
Select ON and OFF whether or not to activate the alarm dis-
play at an event occurrence.
ON:Displays the alarm display at an event occurrence.
OFF:Does not function.
[Monitor2] Settings on monitor 2 display
Perform the display settings for monitor 2 such as the dis-
play mode (task bar style), time display position on/off,
camera title display...

116
It is necessary to adjust the communication speed and use
the same communication protocol with external devices
such as a controller when connecting those external
devices to the DATA port or the SERIAL connector
(RS232C).
It is also necessary to perform the settings for the network
such as the IP address and the gateway address when
operating this unit a PC via a network such as a LAN.
These are the descriptions of how to perform the required
settings for communication with external devices....

117
8Baud Rate
Select the communication speed for data transmission with
a connected device from the following.
2 400/4 800/9 600/19 200/38 400 bps
8Data Bit
It is impossible to change the value for this setting.
8 bit
8Parity
Select a method to check a transmission error at communi-
cation from the following.
NONE:No parity check
EVEN:Even parity
ODD:Odd parity
8Stop Bit
Select a stop bit from the following.
1 bit/2 bit
8Retry Timing
Select a retransmission interval for when data reception is
not...

118
8Baud Rate
Select the communication speed for data transmission with
a connected device from the following.
4 800/9 600/19 200 bps
8Control Camera CH
It is possible to assign camera channels to the RS485 ports
1 and 2 as shown below.
[Screenshot 1]
Start operation from the RS485 Setup menu.
zMove the cursor to Control Camera CH using the
arrows button (CD) and press the SET button.
[Screenshot 2]
The Control Camera CH pop-up window will be displayed.
xMove the cursor to a desired cell in the TERM...

119
8Data Bit
Select a data length for communication from the following.
7/8 bit
8Parity
Select a method to check a transmission error at communi-
cation from the following.
NONE:No parity check
EVEN:Even parity
ODD:Odd parity
8Stop Bit
Select a stop bit from the following.
1/2 bit
8Retry Timing
Select a retransmission interval for when data reception is
not confirmed from the following.
OFF/100 ms/200 ms/400 ms/1 000 ms
[NW Setup 1] Basic network settings
Perform the following basic network settings to...

120
8DNS
Select MANUAL or AUTO to enable searching for an IP
address by its host name using DNS. When OFF is select-
ed for DHCP (no use of the DHCP server), select MANU-
AL and enter the domain name and the DNS server
address. If ON is selected for DHCP (use of the DHCP
server), select AUTO. When DNS is not used, select OFF.
When MANUAL is selected for DNS, enter the DNS server
address for Primary and Secondary.
8DDNS
Select ON and OFF whether or not to use the DDNS
(Dynamic Domain Name Server)....