Panasonic Dbs 824 Instructions Manual

Maximum Dialed Digits For TRS Types 3-6FF7
Maximum Dialed Digits For TRS Types 3-6
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress FF7 
l# 3# (l-15)#
DescriptionThe maximum number of dialed digits on trunks assigned TRS types 3-6 can
be set from 15 to 29, or it can be unlimited
Programming
IFF7 
1# 3## (l-15)#
tMaximum Number of Digits That Can Be Dialed
Note: The default setting is 
** (unlimited)To change
the setting to a limited number of digits, enter 1-15
(see the following table for...

FF73-Digit Toll Restriction For TRS Types 2-6
3-Digit Toll Restriction For TRS Types 2-6
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress FF7 
l# (4-lO)# (0 or l)#
DescriptionUse this program to restrict dialing of special 3-digit numbers (211-811) on
trunks assigned TRS types 2-6(“911” is permitted in all cases 
)
Programming
FF7 l#(/O)# (0 jr l)#
Special NumbersO=Permit
4=211l=Restrict
5=311
6==411
7=511
8=611
9=711
lo=811
Issued 3/l /95DBS 824-l O-4007-9 

7-Digit Toll Restriction For TRS Types 2-6FF7
7-Digit Toll Restriction For TRS Types 2-6
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress 
FR l# (li-15)# (0 or l)#
DescriptionUse this program to restrict dialing of specified 7-digit numbers on trunks
assigned 
TRS types 2-6If this feature is enabled (default setting), the system
checks the number dialed against a table of restricted 
7-digit numbers (see
“Special 
7-Digit Table For TRS Types 2-6” on page 7-21)
Programming
FF7715)# (0 jr...

FF7Dialing Plan Switch
Dialing Plan Switch
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress 
FR l# 16# (0 or l)#
DescriptionThis address allows you to choose between the new North American
Numbering Plan 
(NANP) and the old dialing plan
Selecting the new NANP dialing plan provides greater flexibility for
“exceptions to the rule”, by applying/removing toll restriction to/from
individual extensions, and to dialed area codes, 
offke codes and country
codesSpecific differences between the...

Operator AccessFF7
Operator Access
Software VersionCPC-S and CPC-M, Version 1 0 and higher
AddressFF7 l# 17# (ExtPort)# (0 or l)#
DescriptionThis Operator Access switch works only if the system is programmed to use
the new NANP dialing plan (FF7 
l# 16# l#)Also, this switch applies only
to TRS types 2-6 (TRS types 0 and 1 do not allow outbound dialing, TRS
type 7 allows all dialing)
Use this address to block extension(s) from being able to access a trunk and
dialing “O”, “OO”, “1OXXXO” or “1OlXXXXO” to...

FF7International Calling on Extensions
International Calling on Extensions
Software Version
CPC-S and CPC-M, Version 1 0 and higher
AddressFF7 l# 18## (ExtPort)# (0 or l)#
DescriptionThis address applies only to systems programmed to use the new NANP
dialing plan 
(FF7 l# 16#)It also applies only to TRS types 3-6 (TRS types
O-2 do not allow international dialing, TRS type 7 allows all dialing)
Use this address to allow or restrict international calling on individual
extension(s) that are “exceptions to...

Country Code TableFF7
Country Code Table
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress 
FR I# 19# (Table)# (Code)#
DescriptionThis address applies only to systems programmed to use the new NANP
dialing plan (FF7 
I# 16#)It also applies only to TRS types 3-6 (TRS types
O-2 do not allow international dialing TRS type 7 allows all dialing)
In this address, the DBS 824 system provides a Country Code Table of up to
10 allowable country codes for placing international calls
Each defined...

FF7Equal Access Code Format
Equal Access Code Format
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress FF7 
l# 20# (0 or l)#
DescriptionThis program address determines the dialing format that will be recognized
by the DBS 824 for accessing a preferred interexchange carrier
This address
applies only to outgoing calls that are subject to toll restriction, and to DBS
824 systems that are programmed to use the new NANP dialing plan (see
program address FF7 
l# 16#)Under the old dialing plan,...

Office Code Restriction Table For TRS Types 2-6FF7
Office Code Restriction Table For TRS Types 2-6
Sofhtvare Version
CPC-S and CPC-M, Version 1 0 and higherAddress 
FR 1# 21# (l-lO)# (000-999)#
DescriptionThis address applies only to systems programmed to use the new NANP
dialing plan 
(FM l# 16#)This Office Code Restriction Table allows up to 10 
office codes to be
restricted system-wide for all trunks assigned TRS types 2-6
The system willcheck this table before checking the individual office code(s)...

FF7Area Code Table For TRS Types 3-6
Area Code Table For TRS Types 3-6
Sofhnrare VersionCPC-S and CPC-M, Version 1 0 and higherAddress 
IT7 2# (3-6)# (000-999)# (0 or l)#
DescriptionUse this program to set area code dialing restrictions based on the TRS type
assigned to a trunk
Callers accessing a trunk assigned to TRS types 3-6 are
allowed or denied access to specific area codes according to the settings in
this program
Programming
IFF7 
2# (3-6)# (000-999)# (0 or l)#
i’ t t
TRS Type (3-6)Area...