Panasonic Dbs 824 Instructions Manual

FF8Time Priority Route Tables
Time Priority Route Tables
Software Version - CPCS and CPC-M, Version 1 0 and higherAddress FF8 
5# (l-6)## (l-24)# (114)#Description
When LCR is used, outbound calls are automatically placed on different trunk
groups depending on the time of day
The Time Priority Route Tables
determine which trunks are used during certain times of dayCharacteristics
of Time priority Route Tables are
lTable Number Time priority Route Tables are identified by numbers l-6
In DBS 824...

Time Priority Route TablesFF8day (a “position”), the table determines the time that the LCR trunk group
is used The cost-effectiveness of a trunk group and the time of day it is to
be used determine the position of the Time Priority Route Table
Programming
To create Time Priority Route Tables
FF-)$,,, (T‘W (xyk Group 1-4Time Priority Route
PositionTable (l-6)
To reset a position in a Time Priority Route Table to defaultFF8 
5# (l-6)# (1-24)# CONF ON/OFF
t 2Time Priority Route
Table ( l-6)
Position...

FF8LCR Trunk Groups
LCR Trunk Groups
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress FF8 
W (TrunkGrp)# (Position)# (Trunk)#
DescriptionUse this program to set up LCR trunk groupsSet up LCR trunk groups
before setting up Time Priority Route Tables
LCR uses 4 trunk groups, each consisting of 4 trunks
The trunks in eachgroup are prioritized according to their cost-effectiveness, so that LCR tries
the highest priority trunk in the group first, then the next highest, etc
Different LCR trunk...

LCR Trunk GroupsFF8
ProgrammingFF8 
6# (114)# (l-4)# (1-6 or l-8)#
ft +iLCR Trunk Group
PositionTrunk Number
CPC-S l-6
CPC-M 1-8
8-14
DBS 824-l O-400
Issued 3/l /95 

FF8LCR Delete Tables
LCR Delete Tables
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress FF8 
7# (l-4)# (NNNNNNNNNNNNNNNN)#
DescriptionUse this program to assign deletion digits to a trunk group
When LCR uses
the trunk group, it checks the beginning digits of the dialed number against
the deletion digitsIf the beginning digits match the deletion digits, they are
automatically deleted from the dialed number
The deleted digits are never
OUtpUlSed
Programming
To create an LCR Delete TableFF8...

LCR Add TablesFF8
LCR Add Tables
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress FF8 
8# (l-4)# (NNNNNNNNNNNNNNNN)#
DescriptionDigits to be added to dialed numbers, such as access codes, can be assigned to
trunk groupsWhen LCR uses a trunk in the group, it automatically adds the
digits to the beginning of the dialed numberAfter the digits are added, the
numbers are outpulsed
Programming
To create an LCR Add Table
1~~ ~~~FF8 8# (1-4)# (NNNNNNNNNNNNNNNN)#
LCRTrunk GroupAddition Digits
(up to...

9. Copy Program Settings (FF9)Use the FF9 program addresses in this chapter to copy settings among trunks
extensions and FF keys
This chapter covers the following topics
Trunk Copy
Topic
Page
9-3
1 Extension CopyI 9-4 IFF Key Copy
9-5
issued 3/l/95DBS 824-10-400 

9-2DBS 824-10-400
Issued 3/l/95 

FF9Trunk Copy
Trunk Copy
Software VersionCPCS and CPC-M, Version 1 0 and higherAddress 
FF9 l# (SourceTrunk)## (TargetTrunk)###I
DescriptionUse this program to copy all the attributes of one trunk to anotherCopying
must be done on a trunk-by-trunk basisThe fE.st trunk number in this
address is the 
trunk being copiedfrom (the source), and the second trunk
number is the trunk being copied to (the target)
Programming
Note: You must enter two pound-signs (#I#) at the end of this address
FF9 l# (l-6 or l-8)#...

Extension CopyFF9
Extension Copy
Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress 
FF9 2# (SourceExtPort)# (TargetExtPort)##DescriptionUse this program to copy all the attributes of one extension to another
Copying must be done on an extension-by-extension basisThe first
extension port number of this address is the extension being 
copiedfrom (the
source) the second extension port number is the extension being copied to
(the target)
ProgrammingNote: You must enter two pound-signs 
(##) at...