Panasonic Cz Rtc3 Operating Instructions Manual

							31(EN)
Outing Function
This function prevents the room temperature from rising too high 
(or dropping too low) when no one is in the room due to outing, etc.
  
  
  
  
•  
  
•  
• •  
 
• 
 
  
 
 
     
						

							32(EN)
Outing Function
1
Display the menu screen.
  To return to the previous screenPress .
  To return to the top screenPress  2 times.
2
Select [Outing function]
▲ ▼ → 
3
Select [Select enable/disable] 
and set to [
].
▲ ▼ → ◄ ► → 
4
Select [Set lower/upper limit temp.].
▲ ▼ → 
5
Set the temperature range.
▲ ▼ → ► → ▲ ▼ → 
 →  
(Press 2 times to fi nish.) 
						

							33(EN)
Initial Settings  Clock     Clock type     Operation lock
1
Display the menu screen.
  To return to the previous screenPress .
  To return to the top screenPress  2 times.
2
Select [Initial settings].
▲ ▼ → 
3
Select the item to set.
▲ ▼ → 
Clock
4
Set the date and time.
▲ ▼ → ► → 
 →      (Repeat)
Clock type
4
Select the type to display.
▲ ▼ → 
 →   
(Press 2 times to fi nish.)
AM/PM
24 h
Operation lock
4
Select the type of lock and set to 
[
].
▲ ▼ → ◄ ► →  
 
(Press 2 times to 
fi nish.)
  To cancel lock
Select [-] in step 4.
  Only for [Lock all keys]
Select [YES].
◄ ► → 
(Press 2 times 
to fi nish.) 
						

							34(EN)
Initial Settings
The room to which the remote controller belongs can 
be easily identifi ed.
1
Display the menu screen.
  To return to the previous screenPress .
  To return to the top screenPress  2 times.
2
Select [Initial settings].
▲ ▼ → 
3
Select [Controller name].
▲ ▼ → 
4
Enter the name. (Repeat the same 
procedure for all characters.)
▲ ▼ → ◄ ► → •  Up to 16 characters.
(Space is included in the number of 
characters.)
  To change the character type
Select the character type with ▲ ▼ 
◄ ► and press 
.
Character 
type
  To enter space
Select [Space] with ▲ ▼ ◄ ► and 
press 
.
  To delete 1 character
Select [BS] with ▲ ▼ ◄ ► and 
press 
.
5
Select [Conf].
▲ ▼ ◄ ► → 
 →  (Press 2 times to 
fi nish.)
 Controller name 
						

							35(EN)
Initial Settings  Touch sound     Contrast
 Backlight     Language 
1
Display the menu screen.
  To return to the previous screenPress .
  To return to the top screenPress  2 times.
2
Select [Initial settings].
▲ ▼ → 
3
Select the item to set.
▲ ▼ → 
Touch sound
4▲ ▼ →  →   
(Press 2 times to fi nish.)ON
OFF
Contrast
4◄ ► →  →   
(Press 2 times to fi nish.)
Backlight
4◄ ► →  →   
(Press 2 times to fi nish.)
Language 
4▲ ▼ →  →   
(Press 2 times to fi nish.) 
						

							36(EN)
Initial Settings  Password change    Temp sensor
 Main/sub    Vent output   
 Contact address
1
Display the menu screen.
  To return to the previous screenPress .
  To return to the top screenPress  2 times.
2
Select [Initial settings].
▲ ▼ → 
3
Select the item to set.
▲ ▼ → 
4
Enter the password as necessary.
▲  ▼ → ► → 
(Repeat)
•  Select the number with ▲▼ and move to 
the next fi eld with /£.
Password change
5
Enter a new password.
▲  ▼ → ► → 
(Repeat)
6
Enter the password again to 
confi rm.
▲ ▼ → ► → 
 →  (Press 2 times to 
fi nish.) 
						

							37(EN)
Temp sensor
•  Select the temperature sensor to 
control the room temperature.
Temp 
sensorRemote 
controllerIndoor unit
Main/sub
•  When 2 remote controllers are 
connected to the same indoor unit, 
this registers one remote controller 
as [Main] and the other as [Sub]. 
(There is no difference in function 
between Main and Sub, however, 
when the remote controller sensor is 
selected for the temperature sensor 
setting, the [Main] sensor controls 
the operation.)
Vent output
•  [Set]: When the air conditioner is 
turned ON/OFF, the connected 
ventilation fan is turned ON/OFF, 
too.
•  To interlock the air conditioner and 
the fan, another installation work is 
required.
Contact address
•  If you need to contact for servicing, 
check the back cover of the 
operating instructions for indoor units 
or outdoor units.
*To display each item, see steps 1 to 4  on the previous page. 
						

							38(EN)
Ventilation Setting
1
Display the menu screen.
  To return to the previous screenPress .
  To return to the top screenPress  2 times.
2
Select [Ventilation].
▲ ▼ → 
3
Select [Ventilation ON/OFF].
4
Select [ON] or [OFF]
▲ ▼ → 
 →  (Press 2 times to fi nish.) 
						

							39(EN)
Setting List
This provides the meanings of setting information icons.
1
Display the menu screen.
  To return to the previous screenPress .
  To return to the top screenPress  2 times.
2
Select [Setting list].
▲ ▼ → 
3
Select the item.
▲ ▼ ◄ ► → 
•  Only icons currently being displayed on 
the screen are displayed here.
4
Confi rm.
Confirm, then 
 →  (Press 2 times to 
fi nish.) 
						

							40(EN)
  Setting information icon list
Icon Description Page
[Lock indiv. fl ap] is set. P.13
Switching between Heat and Cool/Dry mode is prohibited (Switching to Auto 
mode is also prohibited.). –
Remote control operation is restricted by a central control device. –
The indoor unit fi lter needs to be cleaned. P.20
The engine oil needs to be replaced (only when the gas heat pump air 
conditioner is used).–
[ON/OFF timer] is set. P.14
[Weekly timer] is set. P.15
Energy saving operation is in process. P.8
The operation capacity of the outdoor unit is restricted. –
[Schedule peak cut] is set. P.28
[Temp auto return] is set. P.24
[Temp range] is set. P.25
[Auto shutoff] is set. P.26
[Repeat off timer] is set. P.30
[Quiet operation] is set. P.22
The temperature sensor of the remote controller is detecting the room 
temperature.P.37
[Operation lock] is set. P.33
Fresh air is used for ventilation.
(Only when connecting a heat exchange ventilation unit or connecting a 
commercially sold fan)P.38
[Outing function] is set. P.31